A multigrid accelerated hybrid unstructured mesh method for 3D compressible turbulent flow

 A cell vertex finite volume method for the solution of steady compressible turbulent flow problems on unstructured hybrid meshes of tetrahedra, prisms, pyramids and hexahedra is described. These hybrid meshes are constructed by firstly discretising the computational domain using tetrahedral elements and then by merging certain tetrahedra. A one equation turbulence model is employed and the solution of the steady flow equations is obtained by explicit relaxation. The solution process is accelerated by the addition of a multigrid method, in which the coarse meshes are generated by agglomeration, and by parallelisation. The approach is shown to be effective for the simulation of a number of 3D flows of current practical interest. Sponsored by The Research Council of Norway, project number 125676/410 Dedicated to the memory of Prof. Mike Crisfield, a respected colleague     

Experimental evidence of a relationship between monomer plasma residence time and carboxyl group retention in acrylic acid plasma polymers

Decreasing carboxyl retention in deposits from the glow region of an acrylic acid plasma was measured by X-ray photoelectron spectroscopy and chemical derivatisation as the collection distance from the monomer vapour inlet was increased. Volatilisation of plasma polymerised acrylic acid was detected after trifluoroethanol derivatisation; this is correlated with evaporation of low molecular weight components observed previously.     

Efficient random subcloning of DNA sheared in a recirculating point-sink flow system

Based on a high-performance liquid chromatographic pump, we have built a device that allows recirculation of DNA through a 63-microm orifice with ensuing fractionation to a minimum fragment size of approximately 300 base pairs. Residence time of the DNA fragments in the converging flow created by a sudden contraction was found to be sufficiently long to allow extension of the DNA molecules into a highly extended conformation and, hence, breakage to occur at midpoint. In most instances, 30 passages sufficed to obtain a narrow size distribution, with >90% of the fragments lying within a 2-fold size distribution. The shear rate required to achieve breakage was found to be inversely proportional to the 1.0 power of the molecular weight. Compared with a restriction digest, up to 40% of all fragments could be cloned directly, with only marginal improvements in cloning efficiency having been observed upon prior end repair with Klenow, T4 polymerase or T4 polynucleotide kinase. Sequencing revealed a fairly random distribution of the fragments.     

The band areas of proteins determined by fluorescent scanning in the commercial automated gel electrophoresis apparatus

An automated gel electrophoresis apparatus, recently available commercially, allows one to follow the band during electrophoresis in real time, and lends itself therefore to an evaluation of bandwidth as a function of migration time (the dispersion coefficient), resolution and band shape. These determinations assume the constancy of band area with migration time and at various gel concentrations. The purpose of the present study was to verify these assumptions. Representative proteins and sodium dodecyl sulfate (SDS)-proteins, either natively fluorescent or fluorescein carboxylate labeled, were found to exhibit band areas which approach constancy as a function of migration time in both agarose and polyacrylamide gel electrophoresis, provided that (i) the protein concentration under the band was low enough to obviate self-quenching of fluorescence; (ii) the separation of the protein of interest from contaminants had progressed sufficiently during the time at which band areas were measured; (iii) the baseline under the peak was sufficiently well defined. However, band areas decrease with increasing gel concentration. Protein peaks exhibited leading and trailing tails. The ratio of the combined tail area to total area appeared to be near-constant at varying migration times. However, that ratio increases with increasing gel concentration. The tail area does not appear to be an artifact of fluorometric detection since it is reproduced upon fluorimetric analysis of the protein eluted from gel slices after electrophoresis. However, it may be due to photochemical destruction under the conditions of repetitive fluorometric peak detection.     

Solving ML equations for 2-parameter Poisson-process models forungrouped software-failure data

Existence conditions are given for maximum likelihood (ML) parameter estimates for several families of 2-parameter software-reliability Poisson-process models. For each such model, the ML equations can be expressed in terms of one equation in one unknown. Bounds are given on solutions to these one equation problems to serve as initial intervals for search algorithms like bisection. Uniqueness of the solutions is established in some cases. Solutions are also tabulated for certain simple cases. Results are given for ungrouped failure data (exact times are available for all failures). ML estimation problems for such a situation are treated as limiting cases of problems based on failure times grouped into intervals of decreasing mesh     

Phase Studies Concerning Sintering in Aluminas Doped with Ti4+

Previous solid state analyses of sintering in Ti⁴⁺-doped-commercial alumina are shown to be in error because a liquid phase exists in the appropriate region of the Al₂O₃−TiO₃−Na₂Ophase diagram at least by 1350^°C, a temperature lower than that at which "solid state" studies were conducted. It is suggested that liquid-phase sintering is a much more common occurrence than was realized formerly.     

The function of bleaching earths in the processing of palm,palm kernel and coconut oils

The results presented in the literature, which attempt to elucidate the mechanisms by which triglyceride oils are bleached by earths, are reviewed. The impact of this work and how the mechanistic proposals affect changes in oil properties are considered, with particular emphasis on the needs of the palm oil processor. Important properties include color, metals and phosphorus content and oxidative stability of the oil. Investigations made in our own laboratories have been aimed at elucidating the effect of varying physical and chemical properties of the bleaching earth on the quality of bleached and deodorized oils. Techniques used in this work are pore-size distribution, surface area, scanning and transmission electron microscopy and a variety of chemical and X-ray analysis methods. The ability to vary such parameters in montmorillonite clays by alteration of process conditions to give materials with specific performance characteristics is demonstrated. Comparisons are made between acid-activated montmorillonites and other clay types.