A Vision-Based Intelligent System for Packing 2-D Irregular Shapes

Packing two-dimensional shapes on a surface such that no shapes overlap and the uncovered surface area is minimized is an important problem that arises in a variety of industrial applications. This paper introduces an intelligent system which tackles the most difficult instance of this problem, where two-dimensional irregular shapes have to be packed on a regularly or irregularly shaped surface. The proposed system utilizes techniques not previously applied to packing, drawn from computer vision and artificial intelligence, and achieves high-quality solutions with short computational times. In addition, the system deals with complex shapes and constraints that occur in industrial applications, such as defective regions and irregularly shaped sheets. We evaluate the effectiveness and efficiency of the proposed method using 14 established benchmark problems that are available from the EURO Special Interest Group on Cutting and Packing.     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.     

Multipopulation model of membrane-aerated biofilms

Biofilms cultivated on oxygen-filled gas-permeable membranes grow differently than conventional biofilms, as the chemical species required for growth diffuse from different sides of the biofilm. Oxygen is delivered directly to the base of the biofilm by the membrane, while organic substrates and other soluble nutrients are provided to the upper surface of the biofilm via the water in which the membranes are immersed. This counterdiffusion of nutrients results in a growth environment very different from that of conventional biofilms that receive both oxygen and other nutrients from the water. In recent years, membrane-supported biofilms have been shown to simultaneously remove chemical oxygen demand (COD) and inorganic nitrogen from wastewater in laboratory studies. Several investigators have developed computer models of these biofilms, but they have all focused on a single population of aerobic bacteria. While these models are useful in characterizing the behavior of these biofilms in pure cultures, they are not useful in modeling the behavior of the biofilms in mixed cultures such as those found in wastewater treatment. In this study, a multipopulation biofilm model was developed that includes aerobic heterotrophs, nitrifiers, denitrifiers, and acetoclastic methanogens. The model was constructed with Aquasim software and can predict the COD and inorganic nitrogen removal behavior observed previously in experimental studies. In this paper we present examples of predicted biofilm behavior and compare the results of this multiple-population model with the single-population models published previously. In addition, the behavior of the biofilm is discussed in terms of application to wastewater treatment.     

Graphitic mesoporous carbon as a durable fuel cell catalyst support

Highly stable graphitic mesoporous carbons (GMPCs) are synthesized by heat-treating polymer-templated mesoporous carbon (MPC) at 2600 °C. The electrochemical durability of GMPC as Pt catalyst support (Pt/GMPC) is compared with that of carbon black (Pt/XC-72). Comparisons are made using potentiostatic and cyclic voltammetric techniques on the respective specimens under conditions simulating the cathode environment of PEMFC (proton exchange membrane fuel cell). The results indicate that the Pt/GMPC is much more stable than Pt/XC-72, with 96% lower corrosion current. The Pt/GMPC also exhibits a greatly reduced loss of catalytic surface area: 14% for Pt/GMPC vs. 39% for Pt/XC-72.     

Enteropathogenic E. coli: intimacy redefined

A 42 yr old male presented with left facial weakness. MRI showed lesions affecting the distal seventh nerve and third division of the trigeminal nerve. The seventh nerve was biopsied and showed a malignant epithelioid schwannoma. The patient underwent extensive resection followed by irradiation. This is one of very few examples of intracranial malignant peripheral nerve sheath tumors and the first reported example of an intracranial malignant epithelioid schwannoma. The literature is reviewed and completeness of resection appears to be the most pertinent prognostic factor.     

Inflammasome Signaling Regulates the Microbial–Neuroimmune Axis and Visceral Pain in Mice

Interactions between the intestinal microbiota, immune system and nervous system are essential for homeostasis in the gut. Inflammasomes contribute to innate immunity and brain–gut interactions, but their role in microbiota–neuro–immune interactions is not clear. Therefore, we investigated the effect of the inflammasome on visceral pain and local and systemic neuroimmune responses after antibiotic-induced changes to the microbiota. Wild-type (WT) and caspase-1/11 deficient (Casp1 KO) mice were orally treated for 2 weeks with an antibiotic cocktail (Abx, Bacitracin A and Neomycin), followed by quantification of representative fecal commensals (by qPCR), cecal short chain fatty acids (by HPLC), pathways implicated in the gut–neuro-immune axis (by RT-qPCR, immunofluorescence staining, and flow cytometry) in addition to capsaicin-induced visceral pain responses. Abx-treatment in WT-mice resulted in an increase in colonic macrophages, central neuro-immune interactions, colonic inflammasome and nociceptive receptor gene expression and a reduction in capsaicin-induced visceral pain. In contrast, these responses were attenuated in Abx-treated Casp1 KO mice. Collectively, the data indicate an important role for the inflammasome pathway in functional and inflammatory gastrointestinal conditions where pain and alterations in microbiota composition are prominent.     

A Novel Test for the Appraisal of Solid/Solid Interfacial Interactions

The Johnson, Kendall and Roberts (JKR) technique has been used with considerable success for assessing solid/solid interfacial interactions over the past 25 years or so. Nevertheless, the contact zone between the two spherical solids is often small and the energy of adhesion scales with the cube of the contact radius (at low load), thus potentially magnifying errors in adhesion assessment. The theoretical aspects of a novel technique are presented here, in which a hollow, slightly inflated, spherical membrane replaces a full sphere, and is placed in contact with a flat rigid solid. A judicious choice of experimental conditions should lead to increased contact radius and the energy of adhesion scales with its square (at low load), thus reducing possible errors. An added advantage is that the effective elasticity of the sphere depends on internal gas pressure. Thus surface and bulk effects are decoupled.     

23—A THEORETICAL ANALYSIS OF THE TENSILE PROPERTIES OF PLAIN-KNITTED FABRICS. PART I: THE LOAD-EXTENSION CURVE FOR FABRIC EXTENSION PARALLEL TO THE COURSES

An investigation is described in which, by means of a two-dimensional model of the plain-knitted structure, load-extension curves for extension in the course direction were calculated theoretically. It was assumed initially that the only mechanism of fabric extension was elastic deformation of the loop shape. Account was taken of setting of the yarns into the relaxed-loop shape, but this was found not to have any significant effect on the theoretical load–extension curves. It was found that the intial portions of these curves were almost linear but that the slope could be greatly affected by the occurrence of lateral yarn compression. When yarn compression was taken into account, good agreement was obtained with experimental results for a nylon-monofilament fabric and a series of wool plain-knitted fabrics.