Synergistic Effects of Polybenzimidazole and Aramide on Enhancing Flame-Retardancy and Solubility

Aromatic and functional polymers with processibility derived from biobased starting materials are prerequisite considering sustainable society. Poly(2,5-benzimidazole)s are rigid-rod polymers to show ultrahigh thermal stability such as flame retardance, while usually suffer from poor solubility. Here, poly(benzimidazole-co-amide)s are synthesized from two biobased monomers, 3,4-diaminobenzoic acid and a semirigid comonomer, 4-aminohydrocinnamic acid. The copolymers with an amide composition of 80 mol% and higher are soluble in widely used polar solvents to fabricate the films keeping high flame retardance, which is comparable with popular high-performance polymers such as aromatic polyimides, polyetheretherketone, polyphenylene sulfide, etc.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

The structure and maximal gain of CW-pumped GaP-AlGaP semiconductor Raman amplifier with tapers on both sides

GaP-AlGaP waveguide semiconductor Raman amplifiers (SRAs) tapered on both sides were fabricated by high-quality GaP-AlGaP liquid phase epitaxial growth using the temperature difference method with controlled vapor pressure (TDM-CVP), photolithography patterning, and reactive ion etching with PCl/sub 3/ gas. Although the finesse of the both-sides-tapered waveguide SRA is lower than previous values for straight or one-side-tapered waveguides, the CW-pumped gain was maximized, and a maximal gain of 4.2 dB was obtained. This letter presents the effect of tapered structures in SRA with CW pumping amplification.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Sensitivity of an anadically oxidized aluminium film on a surface acoustic wave sensor to humidity

The sensitivity, transient response and sensitivity mechanism of a surface acoustic wave humidity sensor using porous anodically oxidized aluminium (alumina) films as mechanical interfaces have been studied theoretically and experimentally. It is found that the sensitivity of alumina films of 1.0 μm thickness is -0.034 m/(s %RH) and is the same order as that of polyimide films. The transient response of alumina films to humidity is about one order faster than that of polyimide films. For the sensitivity mechanism, the phase-velocity change is attributed to the mechanical perturbation caused by the absorption of water molecules. The equivalent density change of alumina films between 0 and 100%RH is about 0.7%. In addition, the actual stiffness constants of alumina films are two orders less than those of bulk alumina.     

Removal of nonionic surfactant by systems based on chloromethylated polystyrene–poly(ethylene glycol)

For the purpose of obtaining compounds which can remove nonionic surfactants in water, chloromethylated polystyrene (CMPS) was allowed to react with triethylene glycol monomethyl ether (3EGMME), tetraethylene glycol (4EG), poly(ethylene glycol) (PEG) 200, 400, 600, 1000, and 1500. The amount of PEG groups combined with CMPS decreased with an increase in the molecular weight of PEG. The ability of the product to remove polyethylene glycol mono-p-nonyl phenyl ether (NP, n = 10), a nonionic surfactant, solutes in water was greater in the product with PEG of greater MW than that with PEG of smaller MW, and in the product with more PEG groups (mol/g prod.) than in that with less PEG groups. The removal behavior of the products conformed to Freundlich's adsorption formula. Constants of the formula, the effect of temperature on the constants, the effect of combined PEG groups on the removed amount, and the removal manner were studied.