Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Parametric modeling of somatosensory evoked potentials

In this paper, we examine methods of characterizing somatosensory evoked potentials (SEP's) in both the time and frequency domains. We have found that the truncated impulse response (TIR) method produced an accurate time domain model of the SEP signals at model orders greatly reduced from the original state space matrix. The TIR method was valuable for smoothing signals that were slightly corrupted by noise. In this case, the simulated data sequence was close to the original data sequence in the mean squared error sense. For signals that were greatly corrupted by noise, the TIR method was not able to perform as well. Therefore, the TIR method was not a feature extraction method but was valuable for data simulation. In the frequency domain, we have used the autoregressive moving average model (ARMA) to parameterize the SEP signal. An overdetermined set of Yule-Walker equations was created to determine the autoregressive (AR) parameters of the original data with the model order established by the singular value decomposition. From these AR parameters, a residual time series was generated which was used to find the moving average parameters. The resulting ARMA model was used to produce a simulated data sequence. The frequency domain characteristics of the simulated sequence and the corresponding power spectral density of the ARMA filter were very close to the periodogram of the original data sequence. Accurate parameterization was achieved for the SEP waveforms at low filter lengths.     

An in vitro model of traumatic neuronal injury: loading rate-dependent changes in acute cytosolic calcium and lactate dehydrogenase release

We developed a new in vitro model of neuronal injury using NT2-N cells to examine the effects of hydrodynamic loading rate on intraneuronal calcium dynamics and lactate dehydrogenase (LDH) release. Our apparatus consisted of a parallel disk viscometer which induced fluid shear stress with well-defined magnitudes and loading rates to cultured cells. We found that the deformation response of the cells was dependent on the severity of the insult, with increased cellular strains generated for higher shear stresses at a constant loading rate. Peak intracellular free calcium concentration correlated with strain, suggesting that mechanical deformation may regulate calcium response. Slowly applied fluid shear stress elicited no response, whereas high loading rates resulted in peak calcium increases 2.9 to 3.6 times baseline values as injury severity was increased. LDH release measured within 5 min after the insult correlated with loading rate. In addition, LDH release continued to increase out to 24 h following high loading rate conditions, demonstrating that the application of fluid shear stress led to prolonged cell damage. The acute response in NT2-N cells subjected to an insult with the CSID is dependent on the loading rate, and these results suggest that initial membrane deformation may trigger subsequent events.     

Optimum design for buckling of plain and stiffened composite axisymmetric shell panels/shells

The buckling of plain and discretely stiffened composite axisymmetric shell panels/shells made of repeated sublaminate construction is studied using the finite element method. In repeated sublaminate construction, a full laminate is obtained by repeating a basic sublaminate, which has a smaller number of plies. The optimum design for buckling is obtained by determining the layup sequence of the plies in the sublaminate by ranking, so as to achieve maximum buckling load for a specified thickness. For this purpose, a four-noded 48-dof quadrilateral composite thin shell element, together with fully compatible two-noded 16-dof composite meridional and parallel circle stiffener elements are used.     

Solution-Processed n-Type Organic Field-Effect Transistors With High on /off Current Ratios Based on Fullerene Derivatives

Solution-processed n-type organic field-effect transistors (OFETs) based on the fullerene derivative {6}-1-(3-(2- thienylethoxycarbonyl)-propyl)-{5}-l-phenyl-[5,6]-C61 (TEPP) and phenyl-C61-butyric acid methyl ester (PCBM) in a multiring source/drain structure are reported. Devices with TEPP show high electron mobility up to 7.8 x 10^-2 cm²/Vs in the saturation regime for bottom-contact OFETs with Au S/D electrodes with a solution-processed fullerene derivative. The ON/OFF ratios reported in this letter, which are in the range of 10⁵ -10⁶, are among the highest values reported for such devices. This mobility is always higher compared to PCBM devices prepared in identical conditions. The mobility of TEPP and PCBM increased with increasing temperatures in the range of 100-300 K with activation energy of 78 and 113 meV, respectively, which suggests that the thermally activated hopping of electrons is dominant in TEPP.     

Analysis of conduction heat transfer problems in steady, 2D regions with circular holes using a special boundary integral method

A special boundary integral method developed for two-dimensional regions containing circular holes is used to calculate temperature and heat transfer on the boundaries of several selected regions. The geometrical configuration of the region is arbitrary and convective boundary conditions are assumed. An important feature of the method is analytic representation of temperature and its normal derivative on the interior circular holes in the form of a harmonic series. This makes the application of the boundary integral method convenient and free from conditioning problems associated with small interior boundaries. Heat transfer from circular isothermal interior holes are calculated for several illustrative examples using three terms of the harmonic series representation for heat transfer at each of the circular boundaries. The results are presented and discussed.     

High-pressure dc sputtering of High-Tc BPSCCO thin films withTc(0) above 100 K

High-T _c Bi(Pb)-Sr-Ca-Cu-O thin films have been made on single-crystal MgO substrates using high-pressure dc sputtering technique. X-ray studies confirm the crystallinity and highly oriented structure withc-axis perpendicular to the substrate. By optimizing the annealing schedule the formation of the high-T _c phase is stabilized. The best film exhibited superconducting transition temperature with zero-resistance temperature,T _c(0), as high as 101 K. Temperature dependence ofJ _c indicates the presence of Josephson-type weak links.