High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

C-t analysis of MOS capacitors under constant current stress

The effect of high oxide field stress is studied using capacitance-time (C-t) measurements of MOS capacitors. The stress results in parallel shifts of the C-t curve along the time axis. The flatband voltage shift ΔV_FB obtained from the initial deep depletion capacitance C(t=0⁺) follows the same trend as that from the high-frequency C-V characteristics. However, the discrepancy between the two flatband voltages becomes larger as the stress increases due to the effect of interface charges on C-t characteristics. The flatband voltage difference is converted to interface trap density, showing a steady increase of interface trap density with stress, similar to that from low-frequency C-V measurements     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

Influence of lips on thin-walled sections

Turning the free edge of an unstiffened flange inwards or outwards to form a ‘lip’, can substantially improve the local buckling resistance of a member. The lip is the most common type of edge stiffener used in cold-rolled, thin-walled sections. In this paper the behaviour of plate elements of thin-walled sections stiffened by compound lips (i.e. lips which are folded twice to form ‘lips on the lips’) is examined both theoretically and experimentally. An outline of a series of tests on compound edge-stiffened thin-walled sections of various geometries is given and some load-end compression displacement paths are compared with the theoretical predictions. Reasonably good agreement is obtained between the experimental and theoretical results. Comparisons of the theoretical predictions with experimental results of other researchers are also presented in this paper.     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

Stress analysis of a cantilevered fixed partial denture with normal and reduced bone support

A two-dimensional finite element model was constructed to analyze the simulated mechanical behavior of a cantilevered fixed partial denture. The variations of the models were made by altering the degree of bone support, the number of splinted abutments, and the length of the pontics. High stress concentrations were observed around the connectors of the fixed prosthesis and the tooth closest to the cantilever. Reduced bone support increased the deflection and stress concentrations. There was reduction in displacement and stress concentration when the teeth were splinted together. To improve the prognosis of the fixed partial denture cantilever, the number of abutments should be increased and the number of pontics decreased.     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.