Anatomical suitability of abdominal aortic aneurysms for endovascular repair

BACKGROUND: Aortic aneurysm anatomy is crucial when considering patients for endovascular repair. The aim of this study was to determine the proportion of patients with aortic aneurysm suitable for endovascular repair with three different graft-stent systems. METHODS: Spiral computed tomographic angiography was used to assess the anatomy of 154 abdominal aortic aneurysms. Measurements were made of aneurysm neck length and diameter, renal artery to aortic bifurcation length, common iliac artery diameter and length, and external iliac artery diameter. Aneurysms were assessed for anatomical suitability for currently available aortoaortic, aortobi-iliac and aortouni-iliac devices. RESULTS: Six patients (4 per cent) had a distal aortic neck suitable for implantation of a straight aortic graft. Fifteen patients (10 per cent) had arterial anatomy suitable for implantation of a bifurcated graft and 85 (55 per cent) patients were suitable for endovascular repair with an aortouni-iliac graft. The primary reasons for unsuitability were: proximal neck length less than 1.5 cm (44 patients), proximal neck diameter greater than 3.0 cm (12), and angulation of the proximal neck (three). A further ten patients were considered unsuitable for an aortouni-iliac graft because of bilateral common iliac artery aneurysms (four), tortuous iliac arteries (four) and narrow external iliac arteries (two). CONCLUSION: The aortouni-iliac device has the widest applicability of the currently available endovascular systems but open repair remains the only option for a large proportion of patients.     

车床静刚度计算机测试系统研制

在分析了车床的结构特点和车削工艺系统的受力情况和借鉴传统车床静刚度仪优点的基础上，研制了一套基于计算机控制的车床静刚度测试系统。系统由计算机作为信号检测、数据处理和控制核心，并配以精密位移传感器、压力传感器和步进电机及其驱动器等。实现了自动加载、卸载，采样，数据处理，直接绘制、显示和打印刚度曲线等功能。系统的成功研制为车床静刚度的测试提供了一种先进手段。实测结果表明，该系统具有自动化程度高、测试效率高、精度高、可靠性高、测试性能稳定的优点。     

用虚拟仪器技术验证牛顿第二定律

牛顿第二定律是经典力学的基本定律之一,为了形象、直观、准确地验证牛顿第二定律,本文利用数字实验系统生动地展示F=ma的关系。通过本实验可以使学生获得更直观的教学感受。     

Quantitation of vitamin K in human milk

A quantitative method was developed for the assay of vitamin K in human colostrum and milk. The procedure combines preparative and analytical chromatography on silica gel in a nitrogen atmosphere followed by reversed phase high performance liquid chromatography (HPLC). Two HPLC steps were used: gradient separation with ultraviolet (UV) detection followed by isocratic separation detected electrochemically. Due to co-migrating impurities, UV detection alone is insufficient for identification of vitamin K. Exogenous vitamin K was shown to equilibrate with endogenous vitamin K in the samples. A statistical method was incorporated to control for experimental variability. Vitamin K₁ was analyzed in 16 pooled milk samples from 7 donors and in individual samples from 15 donors at 1 month post-partrum. Vitamin K₁ was present at 2.94±1.94 and 3.15±2.87 ng/mL in pools and in individuals, respectively. Menaquinones, the bacterial form of the vitamin, were not detected. The significance of experimental variation to studies of vitamin K in individuals is discussed.     

Observation and Modeling of a Room-Temperature Negative Characteristic Temperature 1.3-μm p-Type Modulation-Doped Quantum-Dot Laser

A room-temperature negative characteristic temperature (T₀ ) and ultralow threshold current density (J_th) of 48 Amiddotcm^-2 are demonstrated for a 1.3-mum InAs quantum dot laser. These characteristics are obtained by combining a high-growth-temperature GaAs spacer layer with p-type modulation doping of the quantum dots in multiple layer dot-in-a-well structures. Through a comparison of p-doped and undoped devices, a photon coupling mechanism is proposed to account for the different temperature dependences of Jth for the two devices. Numerical simulations based on a rate equation model, which includes photon coupling between ground and excited quantum dot states, are performed. The simulations are able to account for the very different temperature-dependent Jth behavior of the doped and undoped device     

Layer thickness and draft angle selection for stereolithography injection mould tooling

The introduction of rapid prototyping has allowed engineers and designers to generate physical models of required parts very early on in the design and development phase. Further to this, the use of stereolithography (SL) cavities as a rapid tooling method has allowed plastic prototype parts to be produced in their most common production manner -- by injection moulding. The process is best suited to small production runs where the high costs of conventionally machined tooling is prohibitive. One of the major drawbacks of the SL injectionmoulding process is the susceptibility of the tools to premature failure. SL tools may break under the force exerted by part ejection when the friction between a moulding and a core is greater than the tensile strength of the core, resulting in tensile failure. Very few justified recommendations exist about the choice of mould design variables that can lower the part ejection force experienced and reduce the risk of SL tool failure. This research investigates the ejection forces resulting from SL injection moulding tools which are identical in all respects except for their build layer thickness and incorporated draft angles in an attempt to identify appropriate evidence for recommendations with respect to these design variables and SL injection moulding. The results show that adjustment of draft angle results in a change of part ejection force as a reasonably linear relationship. An adjustment of the build layer thickness results in a change in part ejection force as a more non-linear relationship. The adjustment of build layer thickness had a greater effect on ejection force than the adjustment of draft angle. The results also show that the surface roughness of all tools remains unchanged after moulding a number of parts in polypropylene. A mathematical model was used in an attempt to predict ejection forces according to the moulding material used. This model reflected the experimental results in terms of relative values but not in absolute values, which may be due to inappropriate specific values used in their calculation. Finite element analysis (FEA) was used in an attempt to identify the factors involved in the ejection process. Results indicate that the effect of draft angle on ejection force is due to elastic deformation of the surface roughness. A fact borne out by the lack of damage to the surface after ejection.     

食品安全检测数据仓库技术的应用与研究

主要利用数据仓库技术,以山东地区进出口食品检测实验室的检测数据为分析对象,初次构建了进出口食品农产品实验室检测数据仓库系统,为食品安全风险分析提供了准确科学的数据支持,为实现数据的进一步挖掘和系统平台的开发做好了准备工作。     

Static and dynamic studies of phase composition in a polydisperse system

We have conducted a study of the phase compositions of a ternary solution containing dextran/polyethylene glycol (PEG)/water using UV-visible spectrometry to study the equilibrium behaviour and confocal microscopy to study the dynamic behaviour observed when the system undergoes phase separation driven by the loss of water. Such a study of phase compositions using confocal microscopy is a new development of the technique. In the static experiments, we find a cloud curve, which lies above the coexistence curve on the PEG rich side of the phase diagram, this is found to be in qualitative agreement with calculations of the phase behaviour for a model polydisperse system. In the dynamic experiments, we are able to measure the phase composition using confocal microscopy in the late stages of separation. Here, the compositions lie well inside the coexistence curve at lower drying rates but converge with it at higher drying rates. This is linked to a change in phase morphology: at low rates, a droplet morphology is observed throughout the process whilst at high drying rates a gross phase separation into two layers is observed to occur even at the earliest times probed by the experiment.     

PVC塑窗型材锯铣中心设计研究

介绍了已开发成功的PVC塑窗型材锯铣加工中心,从模块化设计、刀具布局设计、绿色设计和适应性设计几个方面对这一新技术产品的设计思想、方法和关键技术进行了探讨.