Role of Co in formation of Ni-Ti clusters in maraging stainless steel

The effect of Co addition on the formation of Ni-Ti clusters in maraging stainless steel was studied by three dimensional atom probe (3DAP) and first-principles calculation. The cluster analysis based on the maximum separation approach showed an increase in size but a decrease in density of Ni-Ti clusters with increasing the Co content. The first-principles calculation indicated weaker Co-Ni (Co-Ti) interactions than Co-Ti (Fe-Ti) interactions, which should be the essential reason for the change of distribution characteristics of Ni-Ti clusters in bcc Fe caused by Co addition.     

含钡合金的生产及其对钢液脱氧行为的研究

介绍了含钡合金的生产状况。在MoSi2炉上对钢管钢进行了含钡合金脱氧行为的研究，然后在150tLF／VD精炼设备上进行了使用含钡合金的工业试验。研究中主要选取SiAlBa、SiCaBa、SiAlBaCa、SiAlBaCaSr及用于钙处理的SiCa包芯线，并选用Al和FeSiAl作为对比脱氧剂，分别考察了实验室条件下和实际生产过程中，采用钡系合金对钢液脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物的变质作用的机理。     

含钡合金在钢液中的脱氧行为研究

在MoSi2炉上采用MgO质坩蜗对钢管进行了含钡合金脱氧行为的研究。实验中钡系合金主要选取SiAUBa、SiCaBa、SiAlBaCa、SiAlBeCaSr及用于钙处理的SiCa包芯线，选用Al作为对比脱氧剂，考察了钡系合金脱氧的全氧含量，脱氧产物的分布、尺寸和形貌，探讨了钡系合金脱氧和对夹杂物变性作用的机理。     

直流电弧炉长弧泡沫渣技术

本文指出了直流电弧炉采用长弧泡沫渣技术的必要性及该技术的发展现状，总结了炉渣物理性质，化学成分，温度和气源等对炉渣泡沫化的影响，并介绍了电炉泡沫渣的操作工艺及实际应用效果，对宝钢三期１５０ｔＤＣ－ＵＨＰ电弧炉的泡沫渣工艺提出了看法。     

Coordinated formation pattern control of multiple marine surface vehicles with model uncertainty and time-varying ocean currents

This paper presents a data-driven modeling and optimization method for cavity filters, according to a limited amount of measurement data. In the method, a model that reveals the effect of mechanical structure on electrical performance of cavity filters is firstly developed by an improved algorithm, which can increase the modeling accuracy of small data set by incorporating multi-kernel and prior knowledge into the framework of linear programming support vector regression. Then, an approach to optimize the structure of cavity filters is formulated by using the developed data-based model, and the obtained results can assist the fabrication of the same filter in the future. Some experiments from a synthetic example and a practical application of cavity filter have been carried out, and the experimental results confirm the effectiveness of the method. The model is particularly suited to a computer-aided manufacturing of volume-producing filters, and the proposed algorithm shows great potential in some applications where the experimental data are very few and the prior knowledge is available.     

一种基于分段的CRL改进方案

分析了有序顺序表和二叉排序树表的证书撤销列表方案的不足,提出了一种基于分段的证书撤销列表CRL（Certificate Revocation List）改进方案,给出了按撤销证书到期的时间间隔的分段策略,并对CRL结构进行了改进。通过分析表明,缩短了证书用户查找撤销证书的平均搜索长度,在CRL更新时,不但减少了其它已撤销证书的移动次数,而且还减少了CA对CRL重新签名的计算量。     

考虑过剩吸附量修正的页岩气超临界吸附模型

页岩储层的温度、压力高于气体的临界温度和临界压力,气体在页岩上的吸附属于超临界吸附。针对常规吸附模型(R-L、LRC、E-L、E-F)计算得到的绝对吸附量,不能更精确的表征等温吸附实验得到的过剩吸附量问题,引入过剩吸附量对常规多组分吸附模型进行修正。采用非线性拟合的方法得到拟合参数,利用相对误差分析常规吸附模型和超临界吸附模型的拟合效果,研究超临界吸附模型描述页岩气吸附规律的适用性。研究结果表明:各个修正后的吸附模型拟合效果均优于修正前。修正的R-L吸附模型和修正的E-L吸附模型能较好用于描述两组分的超临界吸附特征;修正的E-L吸附模型可以更好地描述页岩气的超临界吸附特征。此次研究为准确、快速预测页岩气藏超临界吸附特征提供了重要的参考。     

Synthesis of Al2O3-SiC powder from electroceramics waste and its application in low-carbon MgO-C refractories

Composite additives are an efficient means to improve the high-temperature stability and slag resistance of low-carbon MgO-C refractories. In this work, Al₂O₃-SiC powder was firstly synthesized from electroceramics waste by carbon embedded method at 1500°C, 1550°C, and 1600°C for 4 h, and then the as-synthesized Al₂O₃-SiC powder was used as an additive to low-carbon MgO-C refractories. The effects of its addition amounts of 0, 2.5 wt.%, 5.0 wt.%, and 7.5 wt.% on the properties of the refractories were investigated in detail. It was found that increasing the heat treatment temperature is beneficial to the phase conversion of mullite and quartz to alumina and silicon carbide in the electroceramics waste. Furthermore, the addition of Al₂O₃-SiC powder effectively improves the performance of low-carbon MgO-C samples, and the formation of spinel dense layer and high-viscosity isolation layer is the internal reason for the improvement of the oxidation resistance and slag resistance of low-carbon MgO-C samples. This work provides ideas for the reuse of electroceramics waste and presents an alternative strategy for the performance optimization of low-carbon MgO-C refractories.