The properties of electroactive ruthenium oxide coatings supported by titanium-based ternary carbides

Electroactive oxide coatings on titanium, known in industrial chlorine production as dimensionally stable anodes (DSA), are of limited service life owing to the dissolution of active oxide, but also due to low corrosion stability of titanium, at high anodic potentials and elevated temperatures. In order to improve the anode stability, ternary carbide, Ti₃SiC₂, could be a promising material for the coating support, since chemical corrosion stability of Ti₃SiC₂ is significantly higher if compared to Ti. In this work, the possibility of the sol-gel preparation of RuO₂-TiO₂ coating on Ti₃SiC₂ is investigated and comparison of the basic characteristics of sol-gel processed oxide coating, Ru_0.5Ti_0.5O₂, applied onto Ti₃SiC₂ and Ti, is reported. Microscopic investigation of the coating surface showed that considerably less cracked coating is formed onto the Ti₃SiC₂ support. Slightly higher voltammetric currents are registered for Ti₃SiC₂-supported coating in H₂SO₄ and NaCl solution. The activity for chlorine evolution is higher, while the currents of oxygen evolution reaction are lower for Ru_0.5Ti_0.5O₂/Ti₃SiC₂ anode in comparison to Ru_0.5Ti_0.5O₂/Ti anode. Even though these preliminary results on the basic electrochemical properties of Ru_0.5Ti_0.5O₂/Ti₃SiC₂ anode and chemical stability of Ti₃SiC₂ are promising, the accelerated stability test in NaCl solution showed that coated Ti₃SiC₂ is not anodically stable and lasts considerably shorter than Ru_0.5Ti_0.5O₂/Ti anode prepared and tested under the same conditions.     

Cellulose membranes for reverse osmosis Part I. RO cellulose acetate membranes including a composite with polypropylene

With the aim of obtaining RO membranes for brackish water desalination from purified celluloses (cotton linters and bleached bagasse pulp), two reactions (heterogeneous and homogeneous) were applied for the synthesis of cellulose acetate (CA). The efficiency of the membranes was measured and compared with those prepared from purchased CA and prepared CA by acetylation of imported high-grade viscose wood pulp. The effect of blending CA with polypropylene (PP), on the efficiency of the prepared RO membranes was also studied. Results showed that the method of preparation of CA plays a profound effect on the salt rejection and water flux of the RO membranes. The efficiencies of RO membranes formed from heterogeneously acetylated celluloses are higher than those prepared from homogeneous ones. Blending the acetylated cellulose with 9% PP wastes improves the efficiency of membranes prepared from the homogeneously acetylated celluloses.     

Oxidation of Hf2SnC and Nb2SnC in Air in the 400–600°C Temperature Range

The oxidation behavior in air of fully dense, predominantly (92+vol.%) single phase, samples of Nb₂SnC and Hf₂SnC was studied in the 400–600°C temperature range. The oxidation products in both cases were SnO, SnO₂ and either Nb₂O₅ or HfO₂. The oxidation is characterized by an initial incubation period, the duration of which decreased with increasing temperatures, followed by a period of near-linear oxidation kinetics. Oxidation at temperatures as low as 400°C for 72 hr resulted in the total disintegration of bulk samples, and their total conversion to oxides. Comparison with published results indicate that the oxidation kinetics of Hf₂SnC are poorer than those of Hf or HfC. Similarly, Nb₂SnC is more prone to oxidation than pure Nb metal.     

Hybrid genetic algorithms and line search method for industrial production planning with non-linear fitness function

Many engineering, science, information technology and management optimization problems can be considered as non-linear programming real-world problems where all or some of the parameters and variables involved are uncertain in nature. These can only be quantified using intelligent computational techniques such as evolutionary computation and fuzzy logic. The main objective of this research paper is to solve non-linear fuzzy optimization problem where the technological coefficient in the constraints involved are fuzzy numbers, which was represented by logistic membership functions using the hybrid evolutionary optimization approach. To explore the applicability of the present study, a numerical example is considered to determine the production planning for the decision variables and profit of the company.     

High‐Temperature Neutron Diffraction,Raman Spectroscopy,and First‐Principles Calculations of Ti3SnC2 and Ti2SnC

Herein, we report—for the first time—on the additive‐free bulk synthesis of Ti₃SnC₂. A detailed experimental study of the structure of the latter together with a secondary phase, Ti₂SnC, is presented through the use of X‐ray diffraction (XRD), and high‐resolution transmission microscopy (HRTEM). A previous sample of Ti₃SnC₂, made using Fe as an additive and Ti₂SnC as a secondary phase, was studied by high‐temperature neutron diffraction (HTND) and XRD. The room‐temperature crystallographic parameters of the two MAX phases in the two samples are quite similar. Based on Rietveld analysis of the HTND data, the average linear thermal expansion coefficients of Ti₃SnC₂ in the a and c directions were found to be 8.5 (2)·10^?6 K^?1 and 8.9 (1)·10^?6 K^?1, respectively. The respective values for the Ti₂SnC phase are 10.1 (3)·10^?6 K^?1 and 10.8 (6)·10^?6 K^?1. Unlike other MAX phases, the atomic displacement parameters of the Sn atoms in Ti₃SnC₂ are comparable to those of the Ti and C atoms. When the predictions of the atomic displacement parameters obtained from density functional theory are compared to the experimental results, good quantitative agreement is found for the Sn atoms. In the case of the Ti and C atoms, the agreement is more qualitative. We also used first principles to calculate the elastic properties of both Ti₂SnC and Ti₃SnC₂ and their Raman active modes. The latter are compared to experiment and the agreement was found to be good.     

Synthesis and application of magnetite polyacrylamide amino-amidoxime nano-composites as adsorbents for water pollutants

In this work, we aimed to develop a feasible method for in situ preparation of a magnetite ionic polymer nanocomposite at room temperature. For this purpose, acrylonitrile (AN) and 2-acrylamido-2-methylpropane sulfonic acid (AMPS) monomers were copolymerized and crosslinked using different monomer mol ratios in the presence of N,N-methylenebisacrylamide (MBA) as crosslinker to produce ionic crosslinked polymers P(AN-co-AMPS. The nitrile groups were converted to amine amidoxime by reacting with hydroxylamine to increase the adsorption characteristics of the ionic polymers. The produced polymers were swelled in iron cations produced from the reaction of ferric chloride and potassium iodide, followed by reaction with an ammonium hydroxide solution to produce magnetite nano-polymer composites. We performed FT-IR and XRD analysis to determine the chemical and crystalline structures, and assessed the morphologies and magnetite content using SEM, TEM and TGA analyses. We investigated the adsorption capacity and mechanism of the prepared magnetite nano-composites as adsorbents for methylene blue, Co²⁺ and Ni²⁺ cations from water.     

Rapid Bonding of Ti3SiC2 and Ti3AlC2 by Pulsed Electrical Current Heating

Inspired by pressure resistance welding of metallic materials, herein we describe how two MAX phases—Ti₃SiC₂ and Ti₃AlC₂—were successfully joined by a rapid electric current heating method in a pulsed electric current sintering furnace. No welding agent was employed and the total processing time was less than 6 min. When the bulk temperature of the joint couple exceeded 1070°C, good joints, with shear strength above 50 MPa, were achieved in both homo‐ and heterojunction joints.     

Low Breakdown Voltage Varistors by Grain Boundary Diffusion of Molten Bi2O3 in ZnO

Diffusion of molten Bi₂O₃ into the grain boundaries of sintered, alumina-doped (0.23 and 0.7 mol%) ZnO pellets resulted in varistors with breakdown voltages in the 3–5 V range and nonlinearity coefficients of 10–24. The varistors were fabricated by spreading a thin layer of Bi₂O₃ powder on the surface of ZnO pellets and heating the combination to various temperatures (860–1155°C) and different times. The highest nonlinearity coefficients (20–24) and lowest breakdown voltages (3–5 V) were recorded in samples annealed at 860°C for 35 min. Longer annealing times and/or higher temperatures resulted in progressively higher breakdown voltages. Eventually the devices became insulating, which was attributed to the formation of an insulating Bi₂O₃ layer between the grains. Separate wetting experiments have shown that the penetration of Bi₂O₃ into ZnO grain boundaries was a strong function of alumina doping —the penetration rate was decreased by a factor of 5–7 as the ZnO was doped with as little as 0.2 mol% alumina. It is this slowing down of the penetration of the ZnO grain boundaries that is believed to be critical in the development of the low breakdown voltages observed.     

An iterative approach for the evaluation of delamination stresses in laminated composites

A computational strategy for the evaluation of delamination stresses in multilayered fibre-reinforced composites is presented. The approach uses special inter-laminar shear elements and an iterative procedure in the calculation of out-of-plane stresses. Both regular and singular elements for the free edge are presented. The solutions are carried on by switching between direct matrix solution methods of small systems of equations and an iterative conjugate gradient method. The proposed discretization avoids ill-conditioning problems, modelling difficulties and large computational cost associated with three-dimensional analysis of delamination of holes, cut-outs, joints and areas of complex stress states.