排序方式: 共有17条查询结果,搜索用时 15 毫秒
1.
本文通过阐述高压冷缩电缆终端头制作工艺和系统的交流耐压试验方法,对高压电缆和高压冷缩电缆终端头的绝缘问题、原因的查找以及处理方法进行了探讨。 相似文献
2.
3.
4.
1 工程概况 某国际广场工程项目位于广州市东南部琶洲地区,总建 筑面积 196466m2,其中地 下建筑面 积 (二 层地下室 )66605m2。负 二层 地下 室标高 为 -11.600m,±0.000以上为群楼和塔楼,群楼部分为 4 层钢筋混凝土结构。本工程有南北 两座塔楼 ,两座塔 楼之间相距 70m。塔楼 相似文献
5.
6.
调配了不同组分类型的车用汽油,并选择常用的丁腈橡胶、聚酯型橡胶、聚醚型橡胶,对车用汽油与橡胶的相容性开展研究。进行了车用汽油浸泡前后橡胶的体积变化率、拉断强度、断裂伸长率、硬度对比试验及车用汽油浸泡橡胶后的实际胶质和颜色对比试验。试验结果表明,在车用汽油浸泡橡胶7d后,丁腈橡胶的体积变化率、拉断强度、断裂伸长率、硬度变化最为显著,聚酯型橡胶其次,聚醚型橡胶的变化较小;车用汽油浸泡不同类型橡胶后,其实际胶质受丁腈橡胶影响最大,聚酯型橡胶影响最小。用方差分析法对橡胶在车用汽油中浸泡后使用性能的影响因素及车用汽油浸泡橡胶后实际胶质的影响因素进行了分析,发现橡胶类型对自身使用性能的下降有决定性的影响;车用汽油浸泡橡胶后实际胶质则同时受车用汽油类型和橡胶类型的影响,与前者的相关性更大。 相似文献
7.
8.
9.
A series of magnesium borate phosphors MgB4O7:Dy, MgB4O7:Mn and MgB4O7:Dy,Mn were prepared and their ther-moluminescence (TL) emission spectra were measured. TL emission bands in 480, 575 and 660 nm at 200 and 360 oC were observed in the MgB4O7:Dy due to the transitions of the trivalent rare earth ions Dy3+. The glow peaks of broad wavelength band around~580 nm at 180 and~290 oC were observed in MgB4O7:Mn due to the emission of Mn2+ions. The main glow peak of MgB4O7 co-doped with Dy and Mn appeared in 580 nm at~360 oC. When MgB4O7 was co-doped with Dy (0.5 mol.%) and different concentrations of Mn (0.01 mol.%-1.0 mol.%), the peak in 580 nm at 360 °C was intensified and broadened as the concentration of Mn increased, while the peaks in 480, 680 and 750 nm below 300 °C remained the characteristic emission of Dy3+and were reduced in intensity. The emission spectra of the MgB4O7:Dy,Mn phosphor showed that the competitive de-excitation processes between Dy3+and Mn2+existed and the energy transfer occurred from Dy3+to Mn2+. These results meant that rare earth and Mn ions in MgB4O7:Dy,Mn might cause the formation of defects complex that dominated the traps and recombination. 相似文献
10.
用高温固相法研制了MgSO4:Dy,MgSO4:Tm和MgSO4:Mn热释光材料,并通过将MgSO4:Dy和MgSO4:Mn混合,以及MgSO4:Tm和MgSO4:Mn混合烧结得到了双掺杂样品MgSO4:Dy,Mn,MgSO4:Tm,Mn。分别测量了这两种样品在不同热处理温度下的三维发光谱。实验结果表明热处理温度为700℃时的样品,在测量加热过程中观察到Dy和Mn离子分别发光,但超过800℃后,Mn发光强度逐渐变弱,而Tm、Dy的高温发光峰逐渐变强,其它温度的发光峰受到抑制。这表明热释光材料中形成的缺陷复合体结构与热处理温度相关,随着热处理温度的升高,愈来愈多的Mn离子与稀土离子结合紧密,因此在热释光发光谱中清楚地观察到Mn离子对稀土离子的能量转移和对Tm、Dy低于400℃发光峰进行抑制的发光过程。 相似文献