Theoretical estimation of dielectric loss of oxide glasses using nonequilibrium molecular dynamics simulations

To theoretically explore amorphous materials with a sufficiently low dielectric loss, which are essential for next-generation communication devices, the applicability of a nonequilibrium molecular dynamics simulation employing an external alternating electric field was examined using alkaline silicate glass models. In this method, the dielectric loss is directly evaluated as the phase shift of the dipole moment from the applied electric field. This method enabled us to evaluate the dielectric loss in a wide frequency range from 1 GHz to 10 THz. It was observed that the dielectric loss reaches its maximum at a few THz. The simulation method was found to qualitatively reproduce the effects of alkaline content and alkaline type on the dielectric loss. Furthermore, it reasonably reproduced the effect of mixed alkalines on the dielectric loss, which was observed in our experiments on sodium and/or potassium silicate glasses. Alkaline mixing was thus found to reduce the dielectric loss.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

Relation between encoder and syndrome former variables and symbol reliability estimation using a syndrome trellis

We derive a linear correspondence between the variables of an encoder and those of a corresponding syndrome former. Using the derived correspondence, we show that the log-likelihood ratio of an information bit conditioned on a received sequence can be equally calculated using the syndrome trellis. It is shown that the proposed method also applies to recursive systematic convolutional codes which are typical constituent codes for turbo codes. Moreover, we show that soft-in syndrome decoding considering a priori probabilities of information bits is possible in the same way as for Viterbi decoding based on the code trellis. Hence, the proposed method can be applied to iterative decoding such as turbo decoding. We also show that the proposed method is effective for high-rate codes by making use of trellis modification.     

1-GHz-spaced 16-channel arrayed-waveguide grating for a wavelength reference standard in DWDM network systems

We fabricated a 1-GHz-spaced 16-channel arrayed-waveguide grating (AWG) by using a new AWG configuration where the path of each arrayed waveguide winds backward and forward across a 4-in diameter wafer without crossing any other waveguides. The ultra-narrow (< 1 GHz) and stable transmission bands of this AWG can be used to construct a wavelength reference standard covering the S, C, and L bands in the dense wavelength-division-multiplexing network systems whose frequency deviation is /spl plusmn/160 MHz.     

Low-loss athermal silica-based lattice-form interleave filter with silicone-filled grooves

We describe a low-loss athermal silica-based interleave filter with a lattice-form structure. We athermalize the filter by using a silicone-filled groove formed in each delay line and we employ a low-loss design to reduce the accumulated groove excess loss in the multiple delay lines. By using these designs, we obtained a very low groove excess loss of 0.4 dB and achieved satisfactory temperature insensitivity and optical characteristics with this filter.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

Extremely low-loss 1.5%-/spl Delta/ 32-channel athermal arrayed-waveguide grating multi/demultiplexer

A silica-based 1.5%-/spl Delta/ 100 GHz-spacing 32-channel athermal arrayed-waveguide grating (AWG) with compact size and extremely low insertion loss is described. By reducing the fibre coupling loss and the excess loss in a silicone-filled groove, an insertion loss of 1.3 dB was achieved with this athermal AWG.     

Theoretical model for flash generation

Reduction of flash generated in a gas vent is of great concern for manufacturers of electronic parts. The present study proposes a theoretical model for flash generation through consideration of flow characteristics in a gas vent. The model predicts the factors controlling flash, i.e., material parameters such as zero‐shear viscosity, crystallization temperature, thermal conductivity, and heat capacity, and process parameters such as injection and mold wall temperatures, packing pressure, and the clearance of a gas vent. On the other hand, we measure the amount of flash generated in the molding of poly(phenylene sulfide) (PPS) composites containing glass fiber and spherical fillers (CaCO₃ or Al₂O₃). Flash reduces with decreasing size of spherical fillers. These experimental data are successfully interpreted using the flash model. Polym. Eng. Sci., 45:198–206, 2005. © 2005 Society of Plastics Engineers     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.