Synthesis of thermoresponsive copolymer/silica-coated magnetite nanoparticle composite and its application for heavy metal ion recovery

To enhance chemical stability and suppress of aggregation of magnetite nanoparticles (MNPs), which are used as a support for thermoresponsive copolymer immobilization, silica coating of the MNPs is applied via the electrooxidation method. Although the resulting silica coated-MNPs also formed aggregates, the size distribution of the aggregate shifted to smaller size range. Because of that, the surface area available for copolymer immobilization increased approximately 6.7 times at maximum as compared with that of the uncoated MNPs. It contributed to the increase of the amount of the immobilized copolymer on the silica-coated MNPs, which is approximately four times larger than that on the uncoated MNPs. Fe₃O₄ dissolution test confirmed enhancement of chemical stability of MNPs. The thermoresponsive copolymer immobilized on the silica-coated MNPs shows the ability to recycle Cu(II) ion from Cu(II) containing solution by changing temperature with significantly shorter time than those in other thermoresponsive adsorbents in gel form.     

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering

Recent activities in the field of Nuclear Operational Management and Nuclear Safety Engineering, the studies related to risk analysis methodology, design, and operational management, physical phenomena, and emergency preparedness and nuclear security, have been progressed. Especially, ‘risk analysis methodology’ and ‘design and operational management’ are the main categories of the field, in which more than half of published articles on Journal of Nuclear Science and Technology are related to these categories.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

A Fuzzy Expert System for Damage Assessment Using Genetic Algorithms and Neural Networks

Abstract: An efficient knowledge-acquisition support method is required for improvement and maintenance of the knowledge base in durability evaluation of an RC bridge deck. Such a method is proposed in this paper to automatically acquire fuzzy production rules. This method makes joint use of genetic algorithms and a neural network. Using a neural network as a subsystem, the evaluation function of genetic algorithms can be provided with the weights of the neural network. Introducing a neural network into genetic algorithms, it is possible to acquire new knowledge so that the method is useful when it is difficult to acquire knowledge in the field.     

Heat transfer enhancement by Marangoni convection in the NH3–H2O absorption process

The objectives of this paper are to quantify the effect of Marangini convection on the absorption performance for the ammonia–water absorption process, and to visualize Marangoni convection that is induced by adding a heat transfer additive, n-octanol. A real-time single-wavelength holographic interferometer is used for the visualization using a He–Ne gas laser. The interface temperature is always the highest due to the absorption heat release near the interface. It was found that the thermal boundary layer (TBL) increased faster than the diffusion boundary layer (DBL), and the DBL thickness increased by adding the heat transfer additive. At 5 s after absorption started, the DBL thickness for 5 mass% NH₃ without and with the heat transfer additive was 3.0 and 4.5 mm, respectively. Marangoni convection was observed near the interface only in the cases with heat transfer additive. The Marangoni convection was very strong just after the absorption started and it weakened as time elapsed. It was concluded that the absorption performance could be improved by increasing the absorption driving potential (x_vb−x_vi) and by increasing the heat transfer additive concentration. The absorption heat transfer was enhanced as high as 3.0–4.6 times by adding the heat transfer additive that generated Marangoni convection.     

Radiative ignition mechanism of solid fuels

Transmittance of external radiation from a CO₂ laser through a boundary layer of decomposition products over a vertical sample surface is measured during the ignition period. The results indicate that there is significant absorption of the external radiation for PMMA, and a lesser but still not negligible amount, for red oak. An increase in gas phase temperature over surface temperature is observed over much of the ignition interval. Using the experimentally measured incident flux at the sample surface, surface temperature history was calculated from a model that included re-radiation and convection losses from the surface, endothermic decomposition and conduction into the material. The results confirm the significant effect of gas phase absorption on surface temperature. Steady-state-derived surface regression rate expression was used for PMMA in this model. The results raise questions about the validity of such data for the dynamic heating conditions during the ignition period. Further studies needed to understand the radiative ignition mechanism are identified.     

Diffusion-controlled size-selective chloride ion sensing in the presence of bromide ion using a thin, nanoporous, plasma-polymerized coating on an Ag/AgCl electrode

We have developed a diffusion-controlled size-selective method for sensing chloride ion in the presence of bromide ion, based on a thin, nanoporous, plasma-polymerized coating of hexamethyldisiloxane on an Ag/AgCl electrode. Sub-nanometer-sized pores responsible for a highly cross-linked polymer network in the plasma-polymerized coating allowed diffusion-controlled permeation of chloride ion while blocking the larger bromide ion. An electrode coating of thickness greater than 70 nm enabled chloride detection in the concentration range 1-10 mM in the presence of 0.63 mM bromide ion. Advantages of this approach are: (1) simple design compared with ionophore-based strategies and (2) compatibility with microfabrication and mass production processes.     

Monte Carlo simulation of hydrogen absorption in palladium and palladium–silver alloys

A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition Pd_xAg_1−x (x=0.7–0.8) under H₂ pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys.     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.