Effect of Electron Correlation on Phonon Spectra in Cuprates

We examine theoretically the phonon dynamics in the electron-phonon-coupled systems. The model Hamiltonian is a one-dimensional Hubbard model where the hopping of electrons induces the electron-phonon coupling. The numerically exact diagonalization of the Hamiltonian with truncation of the total number of phonons is performed. We calculate the phonon excitation spectra and find that the softening of phonons occurs in insulating case, and a diffusive character appears in the metallic case. We also calculate the charge and spin excitation spectra and find that the dynamics of the phonon coupled with the hopping of electrons is affected by the low energy charge and spin excitations.     

Markedly compressible behaviors of gellan hydrogels in a constrained geometry at ultraslow strain rates

The fracture behaviors of gellan hydrogels under compression remarkably depend on the strain rate as well as the boundary conditions for lateral expansion. In the geometry with no constraint for lateral expansion (conventional uniaxial compression), the gels rupture at relatively small strains independently of the compression rates. In contrast, when the gels are compressed extremely slowly (at a strain rate of ca. 10⁻⁵ s⁻¹) in the geometry prohibiting the lateral expansion at their top and bottom surfaces, they are remarkably compressible down to 2% of the initial height without macroscopic fracture and they are accompanied by a large amount of water release. In such markedly compressed gels, many microscopic cracks are formed around the central layer, where strain concentration occurs due to the nonuniform deformation arising from the constrained geometry. In the highly compressible case, the formation of macroscopic cracks is prevented by the localization of microscopic cracks as well as the enhancement in mechanical toughness by a significant increase in polymer concentration due to water release.     

Annual changes in serum vitellogenin concentrations in viviparous eelpout, Zoarces elongatus

Vitellogenin of matrotrophic viviparous eelpout (Zoarces elongatus) was purified from estradiol-17 beta (E2) treated immature male sera by gel chromatography and anion exchange chromatography. Isolated vitellogenin has a molecular weight of 540 kDa estimated by gel chromatography. Serum levels of vitellogenin in females were measured during oocyte development and gestation by single radial immunodiffusion. Serum vitellogenin level was low (less than 0.2 mg/ml) during the early vitellogenic period, increased in the late vitellogenic period to a peak level (6.4 +/- 2.1 mg/ml) at the beginning of gestation. After that it rapidly decreased to a low level (0.1 +/- 0.1 mg/ml) during the early gestation period. Levels of vitellogenin remained low throughout the gestation period. Serum E2 levels in females showed increased from 1.3 to 3.0 ng/ml during the late vitellogenic period, and declined to 0.4 ng/ml during the early gestation period. Serum levels of E2 showed good correlation with serum vitellogenin levels, suggesting that the vitellogenin synthesis is controlled by E2 in this species. These results combined with the matrotrophic growth of embryo during gestation suggest that there is a shift in the synthesis of maternal nutritional products for embryos from the yolk to other nutrients.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Far infrared reflection spectra in narrow-gap semiconductors

Far infrared reflection spectra of Cd_XHg_1?X Se are measured in the region 20 to 600 cm^?1 at temperatures between 5 and 77 K. Reflection spectra are explained well by the dynamic dielectric function which is constructed as a sum of Γ₈?Γ₈ interband, intraband and phonon contributions. The plasmon-LO phonon coupling effect is also discussed.     

Electron transport in InGaO3(ZnO)m (m=integer) studied using single-crystalline thin films and transparent MISFETs

We have investigated the characteristics of transparent metal-insulator-semiconductor field-effect transistors (MISFETs) fabricated using InGaO₃(ZnO)_m (m=integer) single-crystalline thin films as n-channel layers and amorphous alumina as gate insulator films. The MISFETs exhibit good characteristics such as insensitivity to visible light illumination, off-current as low as ∼1 nA with a positive threshold voltage of ∼3 V and on/off current ratio of 10⁵. The field-effect mobility increased from ∼1 to ∼10 cm² (V s)⁻¹ as the m-value increased. Room temperature Hall mobility also increased. However, unexpectedly these values were lower than the field-effect mobility. It is explained by existence of shallow localized state in the homologous compounds.     

The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

Strength and ductility under dynamic loading in fine- grained IN905XL aluminum alloy

Three IN905XL aluminum alloys with fine grain (1 μm), intermediate grain (3 μm), and coarse grain (5 μm) have been developed by a combination of mechanical alloying (MA) and conventional extrusion in order to investigate their mechanical properties at dynamic strain rates of 1 × 10³ and 2 × 10³ s⁻¹ and a quasi-static strain rate of 10^-3 s⁻¹. Flow stresses are found to increase with decreasing grain size for all the strain rates tested. Negative strain-rate sensitivity of flow stress is observed up to 1 × 10³ s⁻¹ in both intermediate- and coarse-grained IN905XL. At the highest strain rate of 2 × 10³ s⁻¹ however, all samples showed a positive strain-rate sensitivity of strength. Total elongation at high strain rates is generally larger than that at low strain rates. Total elongation also decreases with grain size for all the strain rates. This decrease in elongation results from an initiation of microcracks at interfaces between the matrix and particles finely dispersed near grain boundary regions, introduced during MA processing; then, this initiation leads elongation of alloys to small limited values. Formerly with the Department of Mechanical Systems Engineering, University of Osaka Prefecture. This article is based on a presentation made in the symposium “Dynamic Behavior of Materials,” presented at the 1994 Fall Meeting of TMS/ASM in Rosemont, Illinois, October 3-5, 1994, under the auspices of the TMS-SMD Mechanical Metallurgy Committee and the ASM-MSD Flow and Fracture Committee.     

New method for measuring an optical property of a sample treated by FWA

In this article, a new method for measuring a total spectral radiance factor of a FWA‐treated sample illuminated by a specific standard illuminant is introduced. The method replaces an unstable real fluorescent standard by a bi‐spectral luminescent radiance factor data, which works as a virtual fluorescent standard (VFS) by knowing spectral intensity distributions of illuminations applied to the sample. The method utilizes two illuminations I₁ and I₂ whose relative spectral intensity distributions are different from each other and synthesizes a virtual illumination presenting the identical fluorescent spectral radiance factor to that presented by the standard illuminant with the VFS of the specific bi‐spectral luminescent radiance factor by linearly combining I₁ and I₂ with the suitable weighting factors. The applicability of the method is examined in principle by comparing ISO brightness and CIE whiteness index of fluorescent standard paper as a test sample obtained by this new method to the assigned values. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 195–200, 2007     

Surface characterization and catalytic properties of La1−x -Sr x CoO3

The surface chemical states of the perovskite-type compounds, strontium doped lanthanum cobalt oxides (La_1?x Sr _x CoO₃), have been investigated using X-ray photoelectron spectroscopy (XPS). Catalytic oxidations of both methane and CO have also been investigated using flow methods. The chemical composition of the surface of La_1?x Sr _x CoO₃ was very different from that in the bulk, which was measured by X-ray fluorescence spectroscopy (XRFS). The catalytic activity of La_1?x Sr _x CoO₃ increased with an increase in the quantity of cobalt atoms on the surface.