2.4 GHz continuously variable ferroelectric phase shifters using all-pass networks

Continuously variable ferroelectric (BST on sapphire) phase shifters based on all-pass networks are presented. An all-pass network phase shifter consists of only lumped LC elements, and thus the total size of the phase shifter is kept to less than 2.2 mm /spl times/ 2.6 mm at 2.4 GHz. The tunability (C/sub max//C/sub min/) of a BST interdigital capacitor is over 2.9 with a bias voltage of 140 V. The phase shifter provides more than 121/spl deg/ phase shift with the maximum insertion loss of 1.8 dB and the worst case return loss of 12.5 dB from 2.4 GHz to 2.5 GHz. By cascading two identical phase shifters, more than 255/spl deg/ phase shift is obtained with the maximum insertion loss of 3.75 dB. The loss figure-of-merit of both the single- and double-section phase shifters is over 65/spl deg//dB from 2.4 GHz to 2.5 GHz.     

Age alters regional distribution of blood flow during moderate-intensity exercise

During dynamic exercise in warm environments, requisite increases in skin and active muscle blood flows are supported by increasing cardiac output (Qc) and redistributing flow away from splanchnic and renal circulations. To examine the effect of age on these responses, six young (Y; 26 +/- 2 yr) and six older (O; 64 +/- 2 yr) men performed upright cycle exercise at 35 and 60% of peak O2 consumption (VO2peak) in 22 and 36 degrees C environments. To further isolate age, the two age groups were closely matched for VO2peak, weight, surface area, and body composition. Measurements included heart rate, Qc (CO2 rebreathing), skin blood flow (from increases in forearm blood flow (venous occlusion plethysmography), splanchnic blood flow (indocyanine green dilution), renal blood flow (p-amino-hippurate clearance), and plasma norepinephrine concentration. There were no significant age differences in Qc; however, in both environments the O group maintained Qc at a higher stroke volume and lower heart rate. At 60% VO2peak, forearm blood flow was significantly lower in the O subjects in each environment. Splanchnic blood flow fell (by 12-14% in both groups) at the lower intensity, then decreased to a greater extent at 60% VO2peak in Y than in O subjects (e.g., -45 +/- 2 vs. -33 +/- 3% for the hot environment, P < 0.01). Renal blood flow was lower at rest in the O group, remained relatively constant at 35% VO2peak, then decreased by 20-25% in both groups at 60% VO2peak. At 60% VO2peak, 27 and 37% more total blood flow was redistributed away from these two circulations in the Y than in the O group at 22 and 36 degrees, respectively. It was concluded that the greater increase in skin blood flow in Y subjects is partially supported by a greater redistribution of blood flow away from splanchnic and renal vascular beds.     

Medical-grade acrylic adhesives for skin contact

Pressure-sensitive acrylic adhesives for application to skin are made from 2-ethylhexyl acrylate, isooctyl acrylate or n-butyl acrylate copolymerized with polar functional monomers such as acrylic acid, methacrylic acid, vinyl acetate, methyl acrylate, N-vinylcaprolactam, or hydroxyethyl methacrylate. Functional comonomers increase cohesive strength, provide surface polarity, and enhance wear performance. Tack, adhesion to skin, adhesive transfer to skin, and wear performance of the adhesive are governed by the molecular weight, glass transition temperature, and the viscoelastic behavior of the adhesive. Viscoelastic properties of the adhesive as measured by the Williams plasticity number (WPN), dynamic storage modulus (G′), dynamic loss modulus (G″), and tan δ are important polymer properties for good wear performance. Sweating skin, a moist environment, and physical activity are the most important factors influencing the failure of an adhesive tape during wear. A medicalgrade adhesive for application to human skin should be hypoallergenic. Medical-grade adhesives are utilized in making surgical tapes for holding dressings in place, adhesive bandages, adhesive dressings to cover wounds, and surgical operating drapes.     

Rapid Prototyping for Functional Electrical Stimulation Control

The clinical set-up tool integrates fast parameter selection and a user-friendly interface to help electrical muscle stimulators more efficiently treat patients with neurological injuries. A key challenge in increasing functional electrical stimulation systems' clinical acceptance is facilitating or automating parameter selection, optimization, and programming to make the underlying engineering transparent to the user. To this end, we present the clinical set-up tool (CST), a finite-state-machine-based controller that integrates accurate, automatic parameter optimization in an intuitive user interface. Unlike other approaches, we employ a numerical algorithm that uses real-life data and well-defined criteria to rapidly optimize parameter values.     

Healthy Aims: Developing New Medical Implants and Diagnostic Equipment

Healthy Aims is a 23- million, four-year project, funded under the EU's information society technology sixth framework program to develop intelligent medical implants and diagnostic systems (www.healthyaims.org). The project has 25 partners from 10 countries, including commercial, clinical, and research groups. This consortium represents a combination of disciplines to design and fabricate new medical devices and components as well as to test them in laboratories and subsequent clinical trials. The project focuses on medical implants for nerve stimulation and diagnostic equipment based on strain-gauge technology.     

Development of the bus joint for the ITER Central Solenoid

The terminations of the Central Solenoid (CS) modules are connected to the bus extensions by joints located outside the CS in the gap between the CS and torodial field (TF) assemblies. These joints have very strict space limitations. Low resistance is a common requirement for all ITER joints. In addition, the CS bus joints will experience and must be designed to withstand significant variation in the magnetic field of several tenths of a Tesla per second during initiation of plasma. The joint resistance is specified to be less than 4 nΩ.The joints also have to be soldered in the field and designed with the possibility to be installed and dismantled in order to allow cold testing in the cold test facility. We have developed coaxial joints that meet these requirements and have demonstrated the feasibility to fabricate and assemble them in the vertical configuration. We introduced a coupling cylinder with superconducting strands soldered to the surface of the cable that can be installed in the ITER assembly hall and at the cold test facility. This cylinder serves as a transition area between the CS module and the bus extension.We made two racetrack samples and tested four bus joints in our Joint Test Apparatus. Resistance of the bus joints was measured by a decay method and by a microvoltmeter; the value of the current was measured by the Hall probes. This measurement method was verified in the previous tests. The resistance of the joints varied insignificantly from 1.5 to 2 nΩ.One of the challenges associated with a soldered joint is the inability to use corrosive chemicals that are difficult to clean. This paper describes our development work on cable preparation, chrome removal, compaction, soldering, and final assembly and presents the test results.     

3D Active Edge Silicon Detector Tests With 120 GeV Muons

3D detectors with electrodes penetrating through the silicon wafer and covering the edges were tested in the SPS beam line X5 at CERN in autumn 2003. Detector parameters including efficiency, signal-to-noise ratio, and edge sensitivity were measured using a silicon telescope as a reference system. The measured sensitive width and the known silicon width were equal within less than 10 mum.     

Active-edge planar radiation sensors

Many systems in medicine, biology, high-energy physics, and astrophysics require large area radiation sensors. In most of these applications, minimizing the amount of dead area or dead material is crucial. We have developed a new type of silicon radiation sensor in which the device is active to within a few microns of the mechanical edge. Their perimeter is made by a plasma etcher rather than a diamond saw. Their edges can be defined and also passivated by growing, in an intermediate step, a field oxide on the side surfaces. In this paper, the basic architecture and results from a synchrotron beam test are presented.     

Raman microprobe investigation of the calcium phosphate phases of three commercially available plasma-flame-sprayed hydroxyapatite-coated dental implants

The purpose of the current study was to evaluate the crystallographic properties of three commercially plasma-flame-sprayed hydroxyapatite (HAp) coatings on dental implants. For this purpose a Raman microprobe (MOLE U1000) was used. No preparation of the surfaces was necessary to examine the thin ceramic surface layers. Microspectra (5 µm) and macrospectra (100 µm) have been measured and compared to the spectra of crystalline and amorphous HAp as well as to the spectra of tricalciumphosphate. All implants showed spectra that were more like that of the amorphous phase of HAp than any of the other examined reference materials. However, the implant spectra exhibited an extra band that as yet has not been identified. This band is probably indicative of some structure within the sprayed amorphous phase. Such structural effects would result either directly from quenching from the plasma state or by incorporation of titanium into the lattice during plasma treatment.