Arterial embalming method of the cadaver and its application to research

Ever since 1974, the cadaver has been embalmed by the arterial embalming method, using pre-embalming fluid with blood clot disperser and cell conditioner for the removal of blood clots and drainage of blood, at the Department of Anatomy of the Kawasaki Medical School. According to this method, the cadavers are always very well fixed so that they can be used for not only anatomical dissection but also research for the vascular system by vasography, kinematics of the joint and other histologic examinations. In this report we have described our embalming procedure concretely and its application to research.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

Effects of cononsolvency on gelation of poly(vinyl alcohol) in mixed solvents of dimethyl sulfoxide and water

We studied the rates of gelation and phase separation of poly(vinyl alcohol) (PVA) solutions in mixtures of dimethyl sulfoxide (DMSO) and water at 25 °C and found that both the rates show a maximum at a volume fraction of DMSO φ_DMSO=0.60 while gelation was not observed either in pure DMSO or pure water, suggesting that water-DMSO is a cononsolvent system for PVA. On the basis of the data by Cowie [Can J Chem 36 (1961) 2240] we concluded that the 1:2 stable complex between one DMSO molecule and two water molecules is the main cause of this cononsolvency.     

X-ray Photoelectron Spectroscopy Investigation on the Low-Temperature Degradation of 2 mol% Y2O3-ZrO2 Ceramics

2 mol% Y₂O₃-ZrO₂ polycrystals were annealed in water and under vacuum to highlight the effect of the presence of H₂O on the low-temperature degradation transformation. The specimen surfaces with monoclinic phases transformed during annealing in the different environments were analyzed by X-ray photoelectron spectroscopy with special interest on the electron binding energy change of the constituent ions of the 2 mol% Y₂O₃-ZrO₂ ceramics after the degradation transformation. It was found that no change occurred for the electron-bonding energies of core levels of zirconium ions after the transformation, whereas Y-OH bonds were formed during annealing in water. This result suggested a possibility that the preferred hydration of yttrium took place at the surface of Y₂O₃-partially-stabilized ZrO₂, which is likely to be the reason for the low-temperature degradation accelerated by the presence of H₂O.     

Effect of arginine vasopressin (AVP) inhibitor in the inhibition of the peritumoral edema

BACKGROUND: Major depressive disorder is often marked by repeated episodes of depression. We describe recovery from major depression across multiple mood episodes in patients with unipolar major depression at intake and examine the association of sociodemographic and clinical variables with duration of illness. METHODS: A cohort of 258 subjects treated for unipolar major depressive disorder was followed up prospectively for 10 years as part of the Collaborative Depression Study, a multicenter naturalistic study of the mood disorders. Diagnoses were made according to the Research Diagnostic Criteria, and the course of illness was assessed with the Longitudinal Interval Follow-up Evaluation. Survival analyses were used to calculate the duration of illness for the first 5 recurrent mood episodes after recovery from the index episode. RESULTS: Diagnosis remained unipolar major depressive disorder for 235 subjects (91%). The median duration of illness was 22 weeks for the first recurrent mood episode, 20 weeks for the second, 21 weeks for the third, and 19 weeks for the fourth and fifth recurrent mood episodes; the 95% confidence intervals were highly consistent. From one episode to the next, the proportion of subjects who recovered by any one time point was similar. For subjects with 2 or more recoveries, the consistency of duration of illness from one recovery to the next was low to moderate. None of the sociodemographic or clinical variables consistently predicted duration of illness. CONCLUSION: In this sample of patients treated at tertiary care centers for major depressive disorder, the duration of recurrent mood episodes was relatively uniform and averaged approximately 20 weeks.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.