Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Polarity control of GaN epilayers grown on ZnO templates

We report the successful growth of Ga-polar GaN epilayers on O-polar ZnO templates pre-deposited on c-sapphire. Prior to GaN growth, NH₃ is exposed onto the ZnO template. The polarity of the GaN layers is confirmed by etching of the surface and by conversion beam electron diffraction (CBED), while the O-polar ZnO is confirmed by CBED. It is suggested that the NH₃ pre-exposure helps form a Zn₃N₂ layer, which possesses inversion symmetry and inverts the crystal from anion polar to cation polar.     

Multi‐layered flat‐surface micro‐optical components directly molded on an LCD panel

Abstract— We have developed a process to fabricate optical components, such as a lens, prism, or diffuser, directly on to a glass substrate. Processes include precision mastering by diamond cutting and multi‐layer photopolymer (2P) molding to realize flat surfaces and the integration of multiple components with an alignment within a few micrometers.     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Structural development in cycloolefin copolymers under uniaxial elongational flow

Development of structures in new cycloolefin copolymers (COCs) of ethylene–norbornene (E–NB) and ethylene–tetracyclododecene (E–TD) of different NB/TD compositions were investigated under uniaxial elongational flow. For E–NB copolymer, which has multiblock sequences, a shoulder in WAXD at 0.76 nm was evident besides its amorphous halo, and the relative intensity of the peak increased with increasing comonomer content (NB). The appearance of a new peak for E–TD copolymer, and a relatively higher intense peak for E–NB copolymer at the same position of 0.76 nm, indicated that local ordering of the segments occurred when the COC was subjected to uniaxial flow. A lower comonomer composition of elongated COC, at a constant Hencky strain rate, exhibited two T_g values, whereas a higher composition showed a single T_g. Both local ordering and segmentization occurred in low comonomer content COCs but only local ordering occurred in higher comonomer content COCs. Both the shear viscosity and roll processing experiments exhibited similar phenomena of segregation. A model is proposed to illustrate the structure of COC after uniaxial elongation/deformation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3421–3427, 2004     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Structure and properties of nanocomposites based on poly(butylene succinate) and organically modified montmorillonite

Poly(butylene succinate) and organically modified montmorillonite nanocomposites with there different compositions were prepared via melt blending in a twin‐screw extruder. The structure of the nanocomposites was studied with X‐ray diffraction and transmission electron microscopy, which revealed the formation of intercalated nanocomposites, regardless of the silicate loading. Dynamic mechanical analysis revealed a substantial increase in the storage modulus of the nanocomposites over the entire temperature range investigated. The tensile property measurements showed a relative increase in the stiffness with a simultaneous decrease in the yield strength in comparison with that of neat poly(butylene succinate). The oxygen gas barrier property of neat poly(butylene succinate) improved after nanocomposite preparation with organically modified montmorillonite. The effect of the layered‐silicate loading on the melt‐state linear viscoelastic behavior of the intercalated nanocomposites was also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 777–785, 2006     

Organic–silicate hybrid catalysts based on various defined structures for Knoevenagel condensation

Two types of organic–inorganic hybrid base catalysts are prepared. Organic-functionalized molecular sieves (OFMSs), particularly “amine-immobilized porous silicates”, are designed based on common idea to immobilize catalytic active sites on silicate surface. Silicate–organic composite materials (SOCMs), such as “ordered porous silicate–quaternary ammonium composite materials”, are the precursors of ordered porous silicates obtained during the synthesis. Both the OFMS and the SOCM are used as the catalysts for Knoevenagel condensation. Among the OFMSs, there is clear tendency that the use of molecular sieve with larger pore volume and/or surface area gives the product in higher yield. Aminopropylsilyl (AP)-functionalized mesoporous silicates such as AP-MCM-41 gives the product in high yield under mild conditions. No loss of activity is observed after repeated use for three times. The SOCMs are also active for the same reaction. The precursors of the mesoporous silicates are more active than those of microporous silicates. This material can be repeatedly used without significant loss of activity. High activity is not due to the leached species. The active sites of the SOCM catalysts are considered to be SiO⁻ moieties located on the pore-mouth. Activity of the SOCM increases when the reaction is carried out without solvent, whereas decrease in activity of the OFMS is observed in the solvent-free system.     

Living cationic polymerization of isobutyl vinyl ether by the diphenyl phosphate/zinc iodide initiating system

Summary The first example of the living cationic polymerization of isobutyl vinyl ether via the phosphate counteranion has been achieved in toluene below 0°C with a new initiating system that consists of diphenyl phosphate and zinc iodide, (C₆H₅0)₂P(0)0H/ZnI₂. The number-average molecular weight of the polymers increased in direct proportion to monomer conversion, and was in excellent agreement with the calculated value assuming that one polymer chain forms per unit diphenyl phosphate. On addition of a fresh feed of monomer at the end of the polymerization, the added feed was smoothly polymerized at nearly the same rate as in the first stage, and the polymer molecular weight further increased in direct proportion to monomer conversion. Throughout the reaction, the molecular weight distribution of the polymers stayed very narrow (¯M/¯M_n 1.1). At room temperature (+25 °C), however, the molecular weight distribution of the polymers slightly broadened (¯M_w/¯M_n 1.2) at high conversions where the polymer molecular weight became smaller than the calculated value. Evidently, the (C₆H₅0)₂-P(0)0H/ZnI₂ system indeed generates a propagating species of a long life-time at room temperature, but the perfectly living polymerization by this system operates below 0°C.Living cationic polymerization of vinyl ethers by electrophile