Synergistic Effects of Polybenzimidazole and Aramide on Enhancing Flame-Retardancy and Solubility

Aromatic and functional polymers with processibility derived from biobased starting materials are prerequisite considering sustainable society. Poly(2,5-benzimidazole)s are rigid-rod polymers to show ultrahigh thermal stability such as flame retardance, while usually suffer from poor solubility. Here, poly(benzimidazole-co-amide)s are synthesized from two biobased monomers, 3,4-diaminobenzoic acid and a semirigid comonomer, 4-aminohydrocinnamic acid. The copolymers with an amide composition of 80 mol% and higher are soluble in widely used polar solvents to fabricate the films keeping high flame retardance, which is comparable with popular high-performance polymers such as aromatic polyimides, polyetheretherketone, polyphenylene sulfide, etc.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Quality-Assurance Technology in Japan

A survey of the state of SQA in Japan finds that the situation is much like, but slightly different than, that in the US.     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

Morphology of thin anatase coatings prepared from alkoxide solutions containing organic polymer,affecting the photocatalytic decomposition of aqueous acetic acid

Porous anatase coatings were prepared from alkoxide solutions containing organic polymer by a dip-coating technique. The morphology of the coatings, such as pore size, pore distribution and thickness, was controlled. The effects of the morphology of the porous anatase coatings on the photocatalytic activity for the photocatalytic decomposition of aqueous acetic acid were examined.     

Preparation and photoconduction of rapidly quenched films in the Bi2O31bM2O5 system (M=V,Nb and Ta)

The Bi₂O₃1bM₂O₅ films (M=V, Nb and Ta) were prepared by a rapid quenching technique using a twin-roller type equipment. Quenched film of pure Bi₂O₃ partially precipitated a tetragonal phase which differs from well-known β-Bi₂O₃ in structure. In every (Bi₂O₃)_0.975 (M₂O₅)_0.025 composition (2.5% M₂O₅), the tetragonal phase was obtained as single phase, and the tetragonality became greater than that of the pure Bi₂O₃. Beyond this composition, the tetragonality decreased to form δ-phase with a fcc structure with increasing the M₂O₅ content. The lowest V₂O₅ content forming a δ-phase was 5%, while a slight tetragonality still remained in the samples containing 10% Nb₂O₅ and 10% Ta₂O₅, respectively. From the measurement of the photoconductivities of the quenched films, it was proved that a photoconduction appeared in the tetragonal phase while no photoconductivity was observed in the cubic phase. The characteristic of the photoconduction was that a remarkable decrease in the resistivity was observed when a light of ca. 500 nm in wave length was irradiated on the films.     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

Chemical processing and characterization of spinel-type thermistor powder in the Mn-Ni-Fe oxide system

The coprecipitated Mn-Ni-Fe oxalate was prepared from the mixed sulfate solution by optimum pH control. The chemical composition agreed well with that of the starting solution, and the thermal decomposition of the Mn-Ni-Fe oxalate in air below 600 °C led to the direct formation of cubic spinel phase with fine particle size. The sinterability of the calcined powder, the stability of cubic spinel phase and the influence of annealing temperature on electrical properties of the sintered bodies, were investigated.