Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Highly reliable testing of ULSI memories with on-chip voltage-downconverters

Two testing techniques for ultra-large-scale integrated (ULSI) memories containing on-chip voltage downconverters (VDCs) are described. The first in an on-chip VDC tuning technique that adjusts internal V_CC to compensate for the monitored characteristics of the process parameters during repair analysis testing. The second is an operating-voltage margin test, performed at various internal V_CC levels during the water sort test (WT) and the final shipping test (FT)     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

1 V 2 GHz CMOS frequency divider

A new frequency divider, called differential injection locking, is proposed. The proposed divider has no transistor stacking to suppress the performance degradation due to supply voltage reduction. It is shown that the proposed frequency divider achieves 2 GHz with 1 V supply voltage and 540 /spl mu/W power consumption.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.