Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Transient Stress Intensity Factors for Edge and Corner Cracks in Quench-Test Specimens

The transient temperature and stress fields in a quenched rectangular bar were computed and used to determine the stress intensity factors for midside and corner-edge cracks. The stress intensity factors, K ₁, are presented as a function of time, flaw size, and aspect ratio. The variations of AT, along the crack edge are given and the self-limiting growth of the crack depth is discussed in relation to the nonlimited surface growth.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Investigation of Ozone Loss Rate Influenced by the Surface Material of a Discharge Chamber

Decay characteristics of ozone concentration in oxygen in a chamber with three types of wall material (stainless steel, copper, and aluminum) are measured using the 254 nm photoabsorption method. Effective lifetimes of ozone are estimated from decay curves of ozone concentration. These values depend on the wall material: They are largest for stainless steel and smallest for aluminum. The relationship between effective lifetime and gas pressure is investigated precisely to determine three values. The equivalent diffusion coefficient of ozone in oxygen and the reflection coefficient of ozone at the wall correspond to the loss rate of ozone at the wall. The collisional loss (quenching) rate coefficient of ozone in oxygen is also determined.     

11B and 27Al Nuclear Quadrupole Interactions in SiO2-B2O3-Al2O3-R2O Glass Systems

Quadrupole interactions of ¹¹B and ²⁷Al in SiO₂-B₂O₃-Al₂O₃-R₂O glass systems were investigated to determine the structure of these glasses, which should be amenable to chemical strengthening. The ratio of BO₄ units to BO₃ units approached unity as the R₂O/Al₂O₃ ratio for compounds having fixed B₂O₃ contents approached unity. Nuclear quadrupole coupling constants ( e²Qq/h =2.73 to 2.93 MHz) were measured for the NMR spectra of ¹¹B triangles. The line shapes of ²⁷Al spectra varied with chemical composition, but a few glasses exhibited ²⁷Al line shapes similar to those of the AlO₄ triclusters in SiO₂-Al₂O₃-Na₂O glasses. Compositional trends in the formation of BO₄ and AlO₄ were deduced from the NMR spectra.     

Hydrogen entry into steel during atmospheric corrosion process

Hydrogen entry and permeation into iron were measured by an electrochemical method during atmospheric corrosion reaction. The hydrogen permeation was enhanced on passive films because the hydrogen adsorption increased by the hydrogen evolution mechanism which is different from that on a bear iron surface. The permeation rate during a wet and dry corrosion cycle showed a maximum in the drying process depending upon the surface pH and the corrosion potential. The pollutant such as Na₂SO₃ which decreases the pH and the corrosion potential causes an increase in the permeation rate. The mechanism of the change in the permeation rate during the wet and dry cycles is explained by the polarization diagram of the electrode covered by thin water layer.     

Dependence of Vacuum Electrical Breakdown Field and Field Enhancement Factor on the Number of Apertures Drilled in Small Electrodes

Dark current based on field emission current is considered to be a factor causing the vacuum electrical breakdown between multiaperture acceleration grids in the JT‐60 negative ion source. In this paper, we focus on field enhancement factor, which is a key parameter of field emission from the electrode. Vacuum breakdown testing for small‐sized electrodes simulating the multiaperture acceleration grids of the negative ion source was performed. We found the field enhancement factor and breakdown field for multiaperture electrodes, and we investigated the dependence of each parameter on the number of apertures. The results revealed that an increase in the average field enhancement factor after the end of conditioning resulting from an increase in the number of apertures led to a decrease in the dielectric strength of the multiaperture electrodes.     

Finite-dimensional adaptive control for infinite-dimensional systems

This paper deals with the design of a finite-dimensional model reference adaptive controller for a distributed parameter system. The space of inputs and the space of outputs are both one dimensional. First an input—output representation is introduced, using filtered values generated from the inputs and outputs. Next it is shown that we can design a finite-dimensional adaptive control system by a new adaptive law. The new adaptive law guarantees the existence of a large region of attraction from which all signals are bounded and the tracking error converges to a small residual set.     

The Influence Analysis that a Phase Characteristic of the High‐Level Earthquake Gives to Vibration Response Characteristic of the 550‐kV Disconnectors

We developed the 550‐kV disconnectors that strengthened earthquake proofing by the addition of the damper unit and weight reduction of conductive part based on the damage of the 550‐kV disconnectors by the Great East Japan earthquake (March 11, 2011) and inspected the earthquake proofing performance by shake table test. In shake table test, we performed the test by the artificial seismic wave that varied in phase characteristic in addition to the test by resonance method. And, in a high‐level earthquake area, we analyzed it about the influence that a phase characteristic of the artificial seismic wave gave to stress to occur in disconnectors. As a result, it is thought that the stress to occur in disconnectors is decided by a primary natural frequency basically because a bending strain to occur to the disconnectors in the time when the resonance frequency ingredient becomes the big acceleration response value grows big. But, on a particular phase condition, it was confirmed that the bending strain to occur in disconnectors might grow big conspicuously. As for this, the possibility is thought about by influence of higher natural frequency doing superposition.