Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

Markedly compressible behaviors of gellan hydrogels in a constrained geometry at ultraslow strain rates

The fracture behaviors of gellan hydrogels under compression remarkably depend on the strain rate as well as the boundary conditions for lateral expansion. In the geometry with no constraint for lateral expansion (conventional uniaxial compression), the gels rupture at relatively small strains independently of the compression rates. In contrast, when the gels are compressed extremely slowly (at a strain rate of ca. 10⁻⁵ s⁻¹) in the geometry prohibiting the lateral expansion at their top and bottom surfaces, they are remarkably compressible down to 2% of the initial height without macroscopic fracture and they are accompanied by a large amount of water release. In such markedly compressed gels, many microscopic cracks are formed around the central layer, where strain concentration occurs due to the nonuniform deformation arising from the constrained geometry. In the highly compressible case, the formation of macroscopic cracks is prevented by the localization of microscopic cracks as well as the enhancement in mechanical toughness by a significant increase in polymer concentration due to water release.     

Applications of computer and numerical analysis techniques in welding research

In recent years, computer technology has made remarkable progress and a computer has become an indispensable tool for both engineers and scientists. In this article, utilization of computers in welding research is briefly summarized. Their use in numerical analysis is particularly discussed and applied to physical phenomena in molten pool, hydrogen diffusion and residual stresses due to welding. A comparison is made between theoretical and experimental results.     

Binary Adsorption Isotherms of Water and Ethyl Acetate Vapor for Materials Contained in a Box of a Tobacco Product

An experimental study has been carried out on the characteristics of binary adsorption isotherms of water and volatile flavor for typical materials used in a box of a tobacco product or cigarettes. Ethyl acetate chosen as a model for water-soluble volatile flavor. Binary adsorption isotherms for the tobacco, papers, filters, and activated carbons were measured with a flow-type multi-component adsorption system under the canstant conditions of temperature a t 303 K and vapor pressure of water a t 2.5 kPain the vapor pressure range of ethyl acetate from 0 to 4.2 kPa. A linear equation was applied to express the binary adsorption isotherms for the tobacco, papers and filters, while a Dubinin-Astakhov equation was applied for the activated carbons. The binary adsorption was characterized into three groups, depending on the selectivity as well as the mechanism of adsorption; i.e.(l) for tobacco and papers, water was adsorbed much greater rather than ethyl acetate, (2) for filters, ethyl acetate was adsorbed on the surface as great as water, (3) for activated carbons, ethyl acetate was adsorbed much greater onto their micropores rather than water. The results showed that ethyl     

Tribological issues in reducing piston ring friction losses

In this paper improvement in fuel economy by reducing piston ring friction is studied and reduction of piston ring tension and the use of two-ring packages are found to be effective. However, these can be accompanied by adverse effects such as excessive wear and increasing oil consumption, and measures to overcome these problems are studied in detail.     

Power swing analysis in a future metropolitan electric power system on a contingent trip of cryogenic high-power cables

A cryogenic power cable is expected to be capable of carrying bulk power as a main transmission line in a future metropolitan electric power system. It is important to establish a strategy of how to sustain power supply when such a highly densified power supply route trips from the network due to contingency. It is proposed here that the bulk power transmitted by the cryogenic cable could be distributed into the parallel conventional transmission lines by suitable circuit breaker operations in the system. In this process, power-flow routes are forced to be changed with a remarkable modification in the system configuration. In this paper, the power swings associated with the large power-flow change following contingent faults are analyzed by means of a transient network analyzer. It is found that the proposed system modification could be realized without any harmful power swing if the parameters in generators as well as in control devices have conventional magnitudes. It is shown also by simulations that the margin to occurrence in an unstable power swing is left sufficient even if the parameters deviate somewhat from the present magnitudes.     

Pancyclicity of recursive circulant graphs

In this paper, we study the existence of cycles of all lengths in the recursive circulant graphs, and we show a necessary and sufficient condition for the graph being pancyclic and bipancyclic.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Extensions of polyacrylic acid ammonium salts in the adsorption layer to fluidize alumina slurries

An average shell volume occupied in the adsorption layer on alumina by a polyacrylic acid ammonium salts molecule (PAA) defined as the average area occupied by an adsorbed PAA on alumina multiplied by the average thickness of the water layer at the limit of thickening, has been calculated from the adsorbed amount of PAA and from the flow points of alumina in the presence of PAA of different molecular weights. A steric effect of the PAA dispersant on the dispersion of alumina resulted in a flow with no yield stress. This was due to the change of the extension of PAA in the adsorption shell from a sphere to an ellipsoid with a long axis which exceeded the effective distance that the van der Waals attraction force reaches at a molecular weight for the PAA of between 10 000–20 000.