Robust flat filtering DSP based control of the boost converter

The article deals with the design and implementation of a flat filter tracking digital controller for a boost dc-dc power converter. A highly perturbed switched boost converter circuit is shown to be efficiently controlled, in a trajectory tracking task for its non-minimum phase output, by means of a suitable linear filter, here addressed as a flat filter. Flat filtering is a natural robust version of generalized proportional integral control (GPIC) by which the effects of arbitrary time varying exogenous disturbances, unknown endogenous nonlinearities and un-modeled dynamics can be jointly attenuated in a conceptually similar fashion to observer-based active disturbance rejection control (ADRC) and algebraic identification based model free control (MFC) but: a) without using extended state observers and b) respecting the original system order in a time-varying simplified model while avoiding algebraic estimation techniques. The proposed control technique based on the TMS320F28335 digital signal processor chip is tested by means of realistic simulations and experimental setup.     

NURBS-Enhanced Finite Element Method (NEFEM)

The development of NURBS-Enhanced Finite Element Method (NEFEM) is revisited. This technique allows a seamless integration of the CAD boundary representation of the domain and the finite element method (FEM). The importance of the geometrical model in finite element simulations is addressed and the benefits and potential of NEFEM are discussed and compared with respect to other curved finite element techniques.     

Multipass Scratch Behavior of Borided and Nitrided H13 Steel

AISI H13 steel was subjected to boriding and nitriding; its performance was evaluated by the progressive load scratch test, and then by the multipass scratch test (MPST), to evaluate the accumulated damage. Boriding and nitriding were carried out at a temperature of 800 and 580 °C, respectively, both treatments for 1 and 5 h of exposure time. In scratch test, a load range of 3-90 N was used for borides; a higher range (3-180 N) was chosen for nitrides. Critical loads (L_c) were estimated based on optical microscope observations of the scratch tracks. Failure mechanisms and residual depths were examined by scanning electronic microscope and optical profilometry. Finally, using fractions of L_c, MPST was applied on uncoated and coated samples, for 25, 50, 75 and 100 unidirectional scratch cycles. The coefficient of friction (COF) evolution was recorded and analyzed. A decrease in COF was observed as cycles go through; it was initially higher in uncoated sample; moreover, it was observed that normal load was determinant in its behavior, regardless of the treatment time. Nitrided samples exhibited less catastrophic failures over borided ones, also showed a better volume loss/load ratio performance, from 6 to 8 times better compared to borided samples.     

Acoustically driven photon antibunching in nanowires

The oscillating piezoelectric field of a surface acoustic wave (SAW) is employed to transport photoexcited carriers, as well as to spatially control exciton recombination in GaAs-based nanowires (NWs) on a subns time scale. The experiments are carried out in core-shell NWs transferred to a SAW delay line on a LiNbO(3) crystal. Carriers generated in the NW by a focused laser spot are acoustically transferred to a second location, leading to the remote emission of subns light pulses synchronized with the SAW phase. The dynamics of the carrier transport, investigated using spatially and time-resolved photoluminescence, is well-reproduced by computer simulations. The high-frequency contactless manipulation of carriers by SAWs opens new perspectives for applications of NWs in opto-electronic devices operating at gigahertz frequencies. The potential of this approach is demonstrated by the realization of a high-frequency source of antibunched photons based on the acoustic transport of electrons and holes in (In,Ga)As NWs.     

Polarized recombination of acoustically transported carriers in GaAs nanowires

ABSTRACT: : The oscillating piezoelectric field of a surface acoustic wave (SAW) is employed to transport photoexcited electrons and holes in GaAs nanowires deposited on a SAW delay line on a LiNbO3 crystal. The carriers generated in the nanowire by a focused light spot are acoustically transferred to a second location where they recombine. We show that the recombination of the transported carriers occurs in a zinc blende section on top of the predominant wurtzite nanowire. This allows contactless control of the linear polarized emission by SAWs which is governed by the crystal structure. Additional polarization-resolved photoluminescence measurements were performed to investigate spin conservation during transport.     

Determination of fatty acids in the subcutaneous fat of Iberian breed swine by near infrared spectroscopy (NIRS) with a fibre-optic probe

A near infrared spectrometer equipped with a standard 1210/210 bundle remote reflectance fibre-optic probe, with a 5×5 cm quartz window, was used for the determination of fatty acids in the subcutaneous fat of Iberian pigs. A comparative study was made of the determination of fatty acids (C14:0, C16:0, C18:0, C18:1, C18:2, C18:3, C20: 1, Σpolyunsaturated, Σmonounsaturated and Σsaturated) in samples of subcutaneous fat from Iberian pigs by direct application of the fibre-optic probe on samples of whole subcutaneous fat and with cam-lock cups, assessing extracts of total lipids with diethyl ether. The regression method employed was modified partial least squares (MPLS). Calibration of 157 samples, using the fibre optic probe, allowed determination of fatty acids in the following ranges: C14:0 (0.78-1.77), C16:0 (15.87-29.74), C18:0 (4.61-15.90), C18:1 (43.50-61.27), C18:2 (2.03-13.94), C18:3 (0.13-1.14), C20:1 (0.45-2.32), Σpolyunsaturated (2.31-14.82), Σmonounsaturated (47.37-65.62), Σsaturated (22.09-47.31), with corrected standard errors of prediction SEP(C) of 0.093, 0.56, 0.67, 0.94, 0.42, 0.10, 0.20, 0.46, 0.94, 0.83, respectively. The robustness of the method using the fibre-optic probe was tested in a slaughterhouse using 23 samples for external validation, giving multiple correlation coefficients (RSQ) for C14:0, C16:0, C18:0, C18:1, C18:2, C18:3 C20:1, Σpolyunsaturated, Σmonounsaturated, Σsaturated acids of 0.72, 0.94, 0.72, 0.79, 0.88, 0.55, 0.17, 0.88, 0.74, and 0.90, respectively, and a corrected standard error of prediction [SEP(C)] for these acids (%) of 0.11, 0.60, 0.84, 1.20, 0.77, 0.11, 0.30, 0.76, 1.21, and 1.18, respectively.     

Capillary zone electrophoresis in nonaqueous solvents in the presence of ionic additives

Capillary zone electrophoresis (CZE) in nonaqueous media and in the presence of ionic additives has been successfully applied to the determination of compounds that differ only slightly in their electrophoretic mobilities. Triazine herbicides of environmental interest were chosen as test compounds because they behave as very weak bases. CZE separation of these analytes (especially chlorotriazines) in aqueous solution is difficult due to the low pH required for their conversion into protonated cationic form (HA(+)). However, in mixed nonaqueous solvents, 50% (v/v) acetonitrile-methanol, the acid-base characteristics of these compounds are modified, yielding the protonated ionic species that is susceptible to migration when subjected to an electric field. A noteworthy increase in separation selectivity and resolution can be achieved by using ionic additives. Thus, in this mode of capillary zone electrophoresis, separation is based on ionic interactions between the charged analytes and the ionic additive present in the separation medium. These interactions contribute to enhancing mobility differences and to improving analyte separation. For the separation of chloro- and methylthiotriazines, 10 mM perchloric acid in 50% (v/v) acetonitrile-methanol and 20 mM SDS proved to be satisfactory, providing high resolution in short analysis times. The selectivity achieved was found to depend on the degree of association of the analyte with the ionic additive in the nonaqueous medium. This permits manipulation of the selectivity of the electrophoretic separations as a function of the type and concentration of the ionic additive and of the nature of the nonaqueous medium employed.     

Programmed nebulizing gas pressure for efficient and stable capillary electrophoresis-mass spectrometry analysis of anionic compounds in positive separation mode

Here we have developed a method for the analysis of anionic compounds by capillary electrophoresis coupled to electrospray ionization-mass spectrometry (CE-ESI-MS). The strategy proposed is based on the application of programmed nebulizing gas pressure (PNP), which is applied during the different steps of analysis: sample injection, electrophoretic separation, and detection by the mass spectrometer. The proposed procedure prevents the frequent drops in current observed in the analysis of anions and allows high separation efficiency by capillary electrophoresis to be maintained because it is not necessary to employ pressured-assisted electrophoresis. Additionally, for the first time we describe the use of 100 μm capillaries in capillary electrophoresis-mass spectrometry, allowing the loading of larger samples and hence greater sensitivity, with no loss of the efficiency achieved with the 50 μm capillaries usually used.