Cubic–Quartic Optical Solitons with Differential Group Delay for Kudryashov’s Model by Extended Trial Function

Journal of Communications Technology and Electronics - This paper implements mathematically rigorous extended trial function algorithm to address cubic–quartic optical solitons in...     

Review on zirconate-cerate-based electrolytes for proton-conducting solid oxide fuel cell

The performance of low-to-intermediate temperature (400–800?°C) solid oxide fuel cells (SOFCs) depends on the properties of electrolyte used. SOFC performance can be enhanced by replacing electrolyte materials from conventional oxide ion (O^2-) conductors with proton (H⁺) conductors because H⁺ conductors have higher ionic conductivity and theoretical electrical efficiency than O^2- conductors within the target temperature range. Electrolytes based on cerate and/or zirconate have been proposed as potential H⁺ conductors. Cerate-based electrolytes have the highest H⁺ conductivity, but they are chemically and thermally unstable during redox cycles, whereas zirconate-based electrolytes exhibit the opposite properties. Thus, tailoring the properties of cerate and/or zirconate electrolytes by doping with rare-earth metals has become a main concern for many researchers to further improve the ionic conductivity and stability of electrolytes. This article provides an overview on the properties of four types of cerate and/or zirconate electrolytes including cerate-based, zirconate-based, single-doped cerate–zirconate and hybrid-doped cerate–zirconate. The properties of the proton electrolytes such as ionic conductivity, chemical stability and sinterability are also systematically discussed. This review further provides a summary of the performance of SOFCs operated with cerate and/or zirconate proton conductors and the actual potential of these materials as alternative electrolytes for proton-conducting SOFC application.     

Application of GA-Optimized ANNs to Predict the Water Content,CO2 and H2S Absorption Capacity of Diethanolamine (DEA) in Khangiran Gas Sweetening Plant

Theoretical Foundations of Chemical Engineering - In this work, with the aim of accurate prediction of water content, H2S and CO2 absorption capacity of diethanolamine (DEA) solvent in Khangiran...     

Theoretical Prediction of Chiral 3D Hybrid Organic–Inorganic Perovskites

Hybrid organic–inorganic perovskites (HOIPs), in particular 3D HOIPs, have demonstrated remarkable properties, including ultralong charge‐carrier diffusion lengths, high dielectric constants, low trap densities, tunable absorption and emission wavelengths, strong spin–orbit coupling, and large Rashba splitting. These superior properties have generated intensive research interest in HOIPs for high‐performance optoelectronics and spintronics. Here, 3D hybrid organic–inorganic perovskites that implant chirality through introducing the chiral methylammonium cation are demonstrated. Based on structural optimization, phonon spectra, formation energy, and ab initio molecular dynamics simulations, it is found that the chirality of the chiral cations can be successfully transferred to the framework of 3D HOIPs, and the resulting 3D chiral HOIPs are both kinetically and thermodynamically stable. Combining chirality with the impressive optical, electrical, and spintronic properties of 3D perovskites, 3D chiral perovskites is of great interest in the fields of piezoelectricity, pyroelectricity, ferroelectricity, topological quantum engineering, circularly polarized optoelectronics, and spintronics.     

An experimental study of forced convective heat transfer for fully developed Al 2 O 3 –water nanofluid in an annulus tube

Nanofluids have been known as practical materials to ameliorate heat transfer within diverse industrial systems. The current work presents an empirical study on forced convection effects of Al₂O₃–water nanofluid within an annulus tube. A laminar flow regime has been considered to perform the experiment in high Reynolds number range using several concentrations of nanofluid. Also, the boundary conditions include a constant uniform heat flux applied on the outer shell and an adiabatic condition to the inner tube. Nanofluid particle is visualized with transmission electron microscopy to figure out the nanofluid particles. Additionally, the pressure drop is obtained by measuring the inlet and outlet pressure with respect to the ambient condition. The experimental results showed that adding nanoparticles to the base fluid will increase the heat transfer coefficient (HTC) and average Nusselt number. In addition, by increasing viscosity effects at maximum Reynolds number of 1140 and increasing nanofluid concentration from 1% to 4% (maximum performance at 4%), HTC increases by 18%.     

Adaptive stabilization of a class of nonlinear systems using high-gain feedback

This note presents a high-gain feedback stabilizing control algorithm in which the high-gain parameter is adapted on-line. The algorithm is developed for a class of nonlinear systems which can be viewed as the nonlinear counterpart of uniform rank systems. The system can be unknown except for a number of vital pieces of information. For single-input single-output linear systems such information is usually required in the traditional adaptive control literature.     

Complex formation of montmorillonite clay with polymers. Part 2: The use of montmorillonite clay–vinyl monomer complex as a comonomer in the copolymerization reaction of styrene–acrylonitrile monomers

The bulk copolymerization of styrene–acrylonitrile monomers using styrene‐N⁺–montmorillonite complex as a comonomer in the polymerization was studied. The X‐ray diffraction (XRD) analysis showed that part of the styrene‐N⁺–montmorillonite complex remained non‐dispersed (immiscible) and the copolymer was excluded from the interlayer of the immiscible part of the clay. The successive chemical extraction process revealed that a reasonable amount of the styrene–acrylonitrile copolymer was directly attached to the styrene‐N⁺–montmorillonite complex and enveloped the clay. Highly exfoliated clay lamella and nanospheres (3–5 nm) were observed by transmission electron microscopy (TEM). The montmorillonite clay assume two different morphologies, immiscible and exfoliated, on the basis of the XRD and TEM data. A simple method of calculation of the ratio of the exfoliated/immiscible amounts of the clay indicated that the amount of the styrene‐N⁺–montmorillonite complex exfoliated into separate lamella was 40 % (w/w) of the amount of the clay samples containing 2 % of the (styrene‐N⁺–montmorillonite complex) clay. This amount of exfoliated clay decreases with the increase of the concentration of the clay. The presence of the styrene‐N⁺–montmorillonite clay in the copolymerization reaction had a minor effect on both the copolymer composition and the molecular weight. Modification of the clay with the derivatized styrene monomer can achieve a nanocomposite using a percentage no more than 4 % (w/w) of complex in the copolymer. Copyright © 2004 Society of Chemical Industry     

The development and application of a multiple wavelength illumination technique for the vision-based process monitoring of aero-structure riveting

Airframe riveting is a critical process that requires high levels of process monitoring and quality assurance due to the very high risk associated with the failure of such joints. This paper describes the development of the enabling technology developed for a machine vision-based process monitoring system. One of the key factors affecting the performance of a machine vision system is the quality of the lighting. In the application described in this paper the available lighting was severely limited by the confined space in which the system had to operate. The problem was also compounded by the reflective nature of the objects to be examined. The initial images obtained were not suitable for further processing due to the presence of significant shadows and specular reflections. A novel solution to this problem based on multiple wavelength illumination and signal processing is presented along with results from experimental trials of the approach.