Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Flower‐shaped ultra‐wideband fractal antenna

A flower‐shaped ultra‐wideband fractal antenna is presented. It comprises a fourth iterative flower‐shaped radiator, asymmetrical stub‐loaded feeding line, and coplanar quarter elliptical ground planes. A wide operating band of 12.12 GHz (4.58‐16.7 GHz) for S ₁₁ ≤ ? 10 dB is achieved along with an overall antenna footprint of 15.7 × 11.4 mm². In addition, other desirable characteristics, that is, omnidirectional radiation patterns, peak gain upto 5 dB, and fidelity factor more than 75% are achieved. A good agreement exists between the simulation and measured results. The obtained results illustrate that this antenna has wide operating range and compact dimensions than available structures.     

Impact of adhesive ingredients on adhesion between rubber and brass-plated steel wire in tire

Proficiency on underlying mechanism of rubber-metal adhesion has been increased significantly in the last few decades. Researchers have investigated the effect of various ingredients, such as hexamethoxymethyl melamine, resorcinol, cobalt stearate, and silica, on rubber-metal interface. The role of each ingredient on rubber-metal interfacial adhesion is still a subject of scrutiny. In this article, a typical belt skim compound of truck radial tire is selected and the effect of each adhesive ingredient on adhesion strength is explored. Out of these ingredients, the effect of cobalt stearate is found noteworthy. It has improved adhesion strength by 12% (without aging) and by 11% (humid-aged), respectively, over control compound. For detailed understanding of the effect of cobalt stearate on adhesion, scanning electron microscopy and energy dispersive spectroscopy are utilized to ascertain the rubber coverage and distribution of elements. X-ray photoelectron spectroscopy results helped us to understand the impact of Cu_XS layer depth on rubber-metal adhesion. The depth profile of the Cu_XS layer was found to be one of the dominant factors of rubber-metal adhesion retention. Thus, this study has made an attempt to find the impact of different adhesive ingredients on the formation of Cu_XS layer depth at rubber-metal interface and establish a correlation with adhesion strength simultaneously.     

The structure and management of service level agreements innetworks

The paper proposes a structure for quality-of-service (QoS)-centered service level agreements (SLA), and a framework for their real-time management in multiservice packet networks. The SLA is structured to be fair to both parties, the service provider and their customer. The SLA considered here are for QoS assured delivery of aggregate bandwidth from ingress to egress nodes; however, the control and signaling is for the more granular flows or calls. A SLA monitoring scheme is presented in which revenue is generated by the admission of flows into the network, and penalty incurred when flows are lost in periods when the service provider is not SLA compliant. In the SLA management scheme proposed, the results of a prior off-line design are used, in conjunction with measurements taken locally at ingress nodes, to classify the loading status of routes. The routing and resource management are based on virtual partitioning and its supporting mechanism of bandwidth protection. The effectiveness of SLA management is measured by the robustness in performance in the presence of substantial diversity in actual traffic conditions. A simulation testbed called D'ARTAGNAN has been built from which we report numerical results for a case study. The results show that the SLA management scheme is robust, fair and efficient over a broad range of traffic conditions     

Mathematical model for computer simulation and control of steelmaking

A dynamic model for computer simulation and control of steelmaking has been developed. It is essentially based on multicomponent mixed transport control theory with the incorporation of energy balance calculations. The model is applicable to both steelmaking in electric furnaces as well as in oxygen steelmaking converters. The adjustable parameters of the model for simulation of oxygen steelmaking are gas evolution rate (G_co). oxygen flux factor (F_o) and emulsification factor (EM). These simulation parameters, when combined with on-line measurement of off-gas composition and temperature, enable complete dynamic control of the process. The model developed is applied, as an example, to an industrially produced heat in a top blown oxygen steelmaking converter and the results of simulation are discussed.     

An artificial neural network approach on parametric optimization of laser micro-machining of die-steel

In the present research, laser micro machining (LMM) of tungsten-molybdenum general purpose high speed steel (Rex M2) has been studied. Selection of optimum machining parameter combinations for obtaining higher depth of groove and smaller height of recast layer is a challenging task in LMM due to the presence of a large number of process variables. There is no perfect combination of parameters which can simultaneously result in both the highest depth of groove and lowest height of recast layer. This paper presents an attempt to develop a strategy for predicting the optimum machining parameter setting for the generation of the maximum depth of groove with minimum height of recast layer. A feed forward back-propagation neural network has been developed to model the machining process. The model, after proper training, is capable of predicting the response parameters as a function of four different control parameters. Experimental results demonstrate that the machining model is suitable and the optimization strategy satisfies practical requirements. The developed model has been found to be quite unique, powerful and flexible.     

Modified CMA based blind multiuser equaliser with decision directed scheme

A modified constant modulus (CM) algorithm based blind multiuser equaliser with a decision directed (DD) scheme is developed that does not require any mutual decorrelation and is suitable for downlink direct sequence code division multiple access systems. The performance of the proposed time domain adaptive equaliser is evaluated with respect to usual parameters and is found to perform better than the concurrent CM algorithm and DD scheme.     

A new approach to study organic solar cell using Lambert W-function

Organic photovoltaic solar cells bear an important potential of development in the search for low-cost modules for the production of domestic electricity. One of the main differences between inorganic and organic solar cells is that photo-excitation in these materials does not automatically lead to the generation of free charge carriers, but to bind electron–hole pairs (exciton) with a binding energy of about 0.4 eV. Till now various numerical methods using approximations have been reported to study different aspects of organic solar cells. For the first time an accurate method using Lambert W-function is presented to study different parameters of organic solar cells.