Beneficial effects of wettability altering surfactants in oil-wet fractured reservoirs

In fractured reservoirs, an effective matrix-fracture mass transfer is required for oil recovery. Surfactants have long been considered for oil recovery enhancement, mainly in terms of their ability to reduce oil–water interfacial tension. These surfactants are effective when the fractured formations are water-wet, where capillary imbibition of surfactants from the fracture into the matrix contributes to oil recovery. However, another beneficial aspect of surfactants, namely their ability to alter wettability, remains to be explored and exploited. Surfactants capable of altering wettability can be especially beneficial in oil-wet fractured formations, where the surfactant in the fracture diffuses into the matrix and alters the wettability, enabling imbibition of even more surfactant into the matrix. This sequential process of initial diffusion followed by imbibition continues well into the matrix yielding significant enhancements in oil recovery.In order to test this hypothesis of sequential diffusion–imbibition phenomenon, Dual-Drop Dual-Crystal (DDDC) contact angle experiments have been conducted using fractured Yates dolomite reservoir fluids, two types of surfactants (nonionic and anionic) and dolomite rock substrates. A new experimental procedure was developed in which crude oil equilibrated with reservoir brine has been exposed to surfactant to simulate the matrix-fracture interactions in fractured reservoirs. This procedure enables the measurements of dynamic contact angles and oil–water interfacial tensions, in addition to providing the visual observations of the dynamic behavior of crude oil trapped in the rock matrix as it encounters the diffusing surfactant from the fractures. Both the measurements and visual observations indicate wettability alterations of the matrix surface from oil-wet to less oil-wet or intermediate wet by the surfactants. Thus this study is of practical importance to oil-wet fractured formations where surfactant-induced wettability alterations can result in significant oil recovery enhancements. In addition, this study has also identified the need to include contact angle term in the dimensionless Bond number formulations for better quantitative interpretation of rock–fluids interactions.     

In Situ Performance Testing of Deteriorating Water Tanks for Durability Assessment

Reports of failure of existing concrete structures due to a lack of durability, rather than a deficiency in structural strength, has made concrete technologists, engineers, and researchers focus research on the parameters influencing durability performance with respect to time. Systematic performance monitoring, with respect to chosen durability parameters of existing concrete structures, will decide the direction of future research in this area. Inferences based on laboratory simulations and testing need to be confirmed by in situ field measurements and studies. In situ condition rating and performance monitoring surveys have been conducted by many researchers, scientists, and professional associations, and reported in literature. Inferences of few such studies are summarized and discussed. Deterioration of concrete structures constructed in recent times is observed at relatively faster rates, and has been mainly attributed to cracking. Cracking is associated with the use of faster-hydrating portland cements with increased fineness and the tricalcium silicate (C3S) content to support the high speed of modern construction. In the present research, a case study of deteriorated water tank structures situated in the semitropical region of India is presented. Some selected parameters—such as concrete cover, carbonation depth, chloride concentration, compressive strength, etc. which influence long term durability of structures—have been measured.     

Reaction of zirconium fluoride glass with water: kinetics of dissolution

When liquid water contacts a zirconium-barium-lanthanum fluoride glass, at least three different processes occur. Barium and zirconium fluoride dissolve into the water, water penetrates into the glass, and zirconium fluoride crystals grow on the glass surface, in static solution. The rate of dissolution, as measured by solution analysis, is possibly controlled by diffusion in the solid surface; surface blockage and surface reactions are other possible kinetic steps involved. Diffusion in solution is not the controlling mechanism. Hydrogen profiles in the glass surface suggest that the penetration rate of water into the glass is controlled by diffusion and a surface reaction.     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

Photostability of polyetherurethaneureas

Polyetherurethaneureas (PEUUs) were synthesised from polyethylene-glycols (PEGs) of molecular weight 400, 600 and 1000, 4,4′-diphenylmethanediisocyanate (MDI) and aliphatic diamine chain extenders, 1,3-propanediamine (PDA) and 1,6-hexanediamine (HDA). Polymer films were irradiated with 365 nm light at 293 K and the effects of polyether soft segment length and urea hard segment on photo-oxidative stability were studied by following the variation in weight-average molecular weight (M _w), gel formation and stress-strain properties. Changes in ultraviolet and infrared spectroscopy were monitored on photo-oxidation and hydroperoxide content determined. The soft segment length was increased by increasing the molecular weight of PEG from 400 to 1000 and hard segment structure was changed by variation of diamine. It was noted that the structure of urea and polyether soft segment length plays an important role in photostability of PEUUs. PDA chain extended PEUUs were more stable than HDA chain extended PEUUs.     

A protocol for distributed simulation on a microcomputer network

The computer industry has evolved very rapidly from single-user computers to computer networks where users are able to share both local and remote files. Networks of microcomputers facilitate the integration of all information processing for distributed applications such as database processing and electronic mail. One management application of promising potential for computer networks is distributed simulation. Simulation analysis can be useful to essentially all problem-solving and decision-making on the job.

To implement a particular distributed application, computer communication between processors must be considered. Unlike expensive multiprocessor computers, networks of less-expensive microcomputers do not have pre-established communication paths between processors. This paper addresses how this obstacle may be overcome by using communication protocols based on the Open Systems Interconnection (OSI) reference model. Protocol services needed to support a distributed simulation environment will be identified, and their implementation through a prototype will then be investigated and evaluated.     

Selection of optimized features for fusion of palm print and finger knuckle‐based person authentication

The impact of digital technology in biometrics is much more efficient at interpreting data than humans, which results in completely replacement of manual identification procedures in forensic science. Because the single modality‐based biometric frameworks limit performance in terms of accuracy and anti‐spoofing capabilities due to the presence of low quality data, therefore, information fusion of more than one biometric characteristic in pursuit of high recognition results can be beneficial. In this article, we present a multimodal biometric system based on information fusion of palm print and finger knuckle traits, which are least associated to any criminal investigation as evidence yet. The proposed multimodal biometric system might be useful to identify the suspects in case of physical beating or kidnapping and establish supportive scientific evidences, when no fingerprint or face information is present in photographs. The first step in our work is data preprocessing, in which region of interest of palm and finger knuckle images have been extracted. To minimize nonuniform illumination effects, we first normalize the detected circular palm or finger knuckle and then apply line ordinal pattern (LOP)‐based encoding scheme for texture enrichment. The nondecimated quaternion wavelet provides denser feature representation at multiple scales and orientations when extracted over proposed LOP encoding and increases the discrimination power of line and ridge features. To best of our knowledge, this first attempt is a combination of backtracking search algorithm and 2D²LDA has been employed to select the dominant palm and knuckle features for classification. The classifiers output for two modalities are combined at unsupervised rank level fusion rule through Borda count method, which shows an increase in performance in terms of recognition and verification, that is, 100% (correct recognition rate), 0.26% (equal error rate), 3.52 (discriminative index), and 1,262 m (speed).