ESD–RF co-design methodology for the state of the art RF-CMOS blocks

This paper describes an approach to design ESD protection for integrated low noise amplifier (LNA) circuits used in narrowband transceiver front-ends. The RF constraints on the implementation of ESD protection devices are relaxed by co-designing the RF and the ESD blocks, considering them as one single circuit to optimise. The method is applied for the design of 0.25 μm CMOS LNA. Circuit protection levels higher than 3 kV HBM stress are achieved using conventional highly capacitive ggNMOS snapback devices. The methodology can be extended to other RF-CMOS circuits requiring ESD protection by merging the ESD devices in the functionality of the corresponding matching blocks.     

Intraoperative neurological monitoring

Intraoperative neurological monitoring (INM) is the evaluation of the nervous system within the operating room (OR) environment. In this paper, the INM system is tested in a clinical setting in comparison with conventional somatosensory evoked potential (SEP) monitoring. The study results demonstrate the capability of the INM system in extracting clearer and more stable SEP signals. The high SNR of SEP signals collected in various clinical environments, including the OR, makes the INM system a robust platform for continuous monitoring. While the current use of EP monitoring is limited to intermittent analysis by a highly trained clinical neurophysiologist, the authors believe in changing this paradigm by developing continuous monitoring systems, such as the INM system, capable of automated quantitative EP analysis. This noninvasive monitoring modality will allow for a wider range of use in clinical practice. Based on volunteer and clinical patient studies, the INM monitoring system demonstrates much greater reliability and accuracy via the artifact rejection and denoising strategies. It provides more strategic filtering options for different situations under which the clinical SEP response signal could be greatly contaminated and distorted. Furthermore, the INM system offers a promising approach to signal extraction in real-time monitoring during SEP research.     

Approximate channel identification via δ‐signed correlation

A method of approximate channel identification is proposed that is based on a simplification of the correlation estimator. Despite the numerical simplification (no multiplications or additions are required, only comparisons and an accumulator), the performance of the proposed estimator is not significantly worse than that of the standard correlation estimator. A free (user selectable) parameter moves ‘smoothly’ from a situation with small sum‐squared channel estimation error but hard‐to‐identify channel peaks, to one with a larger sum‐squared estimation error but easy‐to‐identify channel peaks. The proposed estimator is shown to be biased and its behaviour is analysed in a number of situations. Applications of the proposed estimator to sparsity detection, symbol timing recovery and to the initialization of blind equalizers are suggested. Copyright © 2002 John Wiley & Sons, Ltd.     

Prototype test on X-bracing panels using cold-formed lipped angles

The behavior and suitability of cold-formed lipped angle members for X-bracing with redundant have been studied. For the purpose, two full-scale panel tests were carried out. The first panel was designed so that the compression member would fail by buckling in flexural mode and the second panel in flexural-torsional mode. The members were designed using ASCE Manual No. 52. Theoretical aspects of least radius of gyration and buckling behavior of this bracing system have been discussed. The investigation on first panel, revealed that the member would buckle only in the flexural-torsional mode although flexural buckling would govern the design. The second panel test result showed that, the buckling mode and strength of the system for lipped angle sections can be predicted reasonably well.     

A simple method to estimate gain-bandwidth product and the secondpole of the operational amplifiers

A method for realizing a sine-wave voltage-controlled oscillator (VCO) with a linear frequency to control voltage characteristics over three decades of frequencies, or more, in one sweep is discussed. The method employed is the conversion of a simple integrated square-wave VCO into a sine-wave VCO by separating the first-harmonic component and providing frequency shifting to achieve the desired output range. The sources of distortion of the output waveform are shown to be higher-order components of the square-wave used and higher-order components produced in the mixer. Possible improvements of the circuit are suggested, including the use of higher-order filters to reduce distortion and the use of a square-wave VCO operating at higher frequencies to provide operation at higher frequencies or over wider sweep ranges     

Control of power factor correcting boost converter withoutinstantaneous measurement of input current

This paper proposes a new control method for the constant-frequency control of power factor correcting boost power converter using a sinewave template modulated PWM signal which eliminates the need for instantaneous measurement of the line current for the switching control of the boost converter. The control strategy is based on the notion that the line current can be forced to trace a deterministic waveform such as a sinusoid by considering the implicit model of the sinewave in the boost converter controller structure. The modulating sinewave template is generated using the line voltage, the boost converter output voltage and the load current. The paper provides the analysis and the design of the controller and presents simulation and implementation results to demonstrate its effectiveness     

Point-based manifold harmonics

This paper proposes an algorithm to build a set of orthogonal Point-Based Manifold Harmonic Bases (PB-MHB) for spectral analysis over point-sampled manifold surfaces. To ensure that PB-MHB are orthogonal to each other, it is necessary to have symmetrizable discrete Laplace-Beltrami Operator (LBO) over the surfaces. Existing converging discrete LBO for point clouds, as proposed by Belkin et al. [CHECK END OF SENTENCE], is not guaranteed to be symmetrizable. We build a new point-wisely discrete LBO over the point-sampled surface that is guaranteed to be symmetrizable, and prove its convergence. By solving the eigen problem related to the new operator, we define a set of orthogonal bases over the point cloud. Experiments show that the new operator is converging better than other symmetrizable discrete Laplacian operators (such as graph Laplacian) defined on point-sampled surfaces, and can provide orthogonal bases for further spectral geometric analysis and processing tasks.