Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Evaluation of microbial toxins,trace elements and sensory properties of a high-theabrownins instant Pu-erh tea produced using Aspergillus tubingensis via submerged fermentation

Theabrownins (TB) are polymeric phenolic compounds associated with the multiple bioactivities of Pu-erh tea, a post-fermented Chinese dark tea. High-TB instant Pu-erh tea was produced via a novel submerged fermentation (SF) using Aspergillus tubingensis and compared with samples produced commercially via the conventional solid-state fermentation (SSF). Viable microorganisms and microbial toxins, especially aflatoxins B₁, G₁, B₂, G₂, cyclopiazonic acid, fumonisins B₁, B₂, B₃ and ochratoxin A, were below the detection limit in all samples. Fewer microbial metabolites were found in SF instant tea compared with the SSF teas. Based on an adult consuming 1 g of instant Pu-erh tea daily, the dietary intake of investigated elements was below the safe limits recommended by various authorities. Tasters viewed the instant tea infusions as very mild, smooth, mellow and full. This suggested that submerged fermentation using A. tubingensis offers a speedy and safe alternative to commercial production of instant Pu-erh tea.     

Fast internal dynamics in polyelectrolyte gels measured by dynamic light scattering

Summary Dynamic light scattering was used to investigate the dynamics of sodium poly(styrene sulfonate) and fully neutralized poly(acrylic acid) gels as a function of the degree of swelling and weight ratio of cross-linking agent. It was shown that the collective diffusion coefficient increases with increasing degree of swelling and that the diffusion coefficient shows stronger concentration dependence than predicted by scaling arguments. For gel samples measured at the swelling equilibrium, the diffusion coefficient increases with increasing gel concentration for both gel systems.     

The social consequences of expressive suppression.

At times, people keep their emotions from showing during social interactions. The authors' analysis suggests that such expressive suppression should disrupt communication and increase stress levels. To test this hypothesis, the authors conducted 2 studies in which unacquainted pairs of women discussed an upsetting topic. In Study 1, one member of each pair was randomly assigned to (a) suppress her emotional behavior, (b) respond naturally, or (c) cognitively reappraise in a way that reduced emotional responding. Suppression alone disrupted communication and magnified blood pressure responses in the suppressors' partners. In Study 2, suppression had a negative impact on the regulators' emotional experience and increased blood pressure in both regulators and their partners. Suppression also reduced rapport and inhibited relationship formation. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Effect of sampling density on the measurement of stream condition indicators in two lowland Australian streams

There is widespread application of indicators to the assessment of environmental condition of streams. These indicators are intended for use by managers in making various comparative and absolute assessments and often have a role in resource allocation and performance assessment. Therefore, the problem of formally defining confidence in the results is important but difficult because the sampling strategies used are commonly based on a compromise between the requirements of statistical rigour and the pragmatic issues of access and resources. It is rare to see this compromise explicitly considered and consequently there is seldom quantification of the uncertainty that could affect the confidence a manager has in an indicator. In this paper, we present a method for quantitatively assessing the tradeoffs between sampling density and uncertainty in meeting various monitoring objectives. Assessments using judgement‐based representative reaches are shown to be unreliable; instead a sampling approach is recommended based on the random selection of measuring sites. A detailed dataset was collected along two streams in Victoria, Australia, and the effect of sampling density was assessed by subsampling from this dataset with precision related to the number of sites assessed per reach length and the intensity of the sampling at each site. The sampling scheme to achieve a given precision is shown to depend on the monitoring objective. In particular, three objectives were considered: (1) making a baseline assessment of current condition; (2) change detection; and (3) detection of a critical threshold in condition. Change detection is shown to be more demanding than assessing baseline condition with additional sampling effort required to achieve the same precision. Sampling to detect a critical threshold depends on nominating acceptable values of Type I and II error and the size of the effect to be detected. Copyright © 2006 John Wiley & Sons, Ltd.     

Mathematical model of an industrial robot with articulated configuration and six degrees of freedom

This paper analyses the load influence on a d.c. drive motor servo system for all six degrees of freedom of industrial robots with an articulated configuration. Through the analyses, the analytical equations of total inertia and gravitation moments of an industrial robot servo system for external coordinate function were obtained. A mathematical model of an electro-mechanical industrial robot system was also developed.     

联合式电路保护有助于防止损坏DVB网络设备

随着广播、电信和IT业的融合，未来的电话和数字电视都将成为互联网上的应用，这样就需要采用新型的客户端设备（CPE）和网络基础设施，以适应更高数据传输速率的要求，并满足新出现的DVB—T／S／C标准以及符合当前和提议中的通讯要求。     

Kinetic Monte-Carlo simulation of network formation

Summary the simulation described in Part I was applied to random step polyaddition of a trifunctional monomer and the results were compared with exact solution for an infinite system. The gel point conversions, the weight-average degree of polymerization before (P _w) and beyond (P _w,sol) the gel point, the sol fraction and the cycle rank were used for comparison. The best way for detection of the gel point conversion is the extrapolation of the gel fraction, w _g, to w _g=0. The largest fluctuations are exhibited by P _w and P _w,sol. To get results closer to the exact ones, one can repeat several experiments with smaller number of units or increase the number of units, the former way being somewhat more economical. Typical orders of magnitude used were 10⁷ monomeric units.