Experimental and numerical analysis of the influence of cable tray arrangements on the resulting mass loss rate and fire spreading

In the context of industrial buildings and power plants, electrical installations and cable trays represent a main fuel load and a potential initial fire source due to possible short circuits or comparable malfunction. Furthermore, a fire can spread from one tray to additional trays mounted above and/or horizontally on one tray. Because of the high significance of cable fires, several research projects have been carried out, investigating the fire behaviour of cables from small‐scale tests, eg, the cone calorimeter, up to large‐scale tests, analysing complete cable tray constructions. The goal of the work presented in this paper is the extension of the knowledge regarding the influence of geometrical parameters like the packing density and tray distance on the burning behaviour and fire spread of cable tray installations. The results are considered, together with test results from the literature, to quantify the main physical parameters describing the burning behaviour. In a next step, the general applicability of these parameters as input data for the parametrization of the source term of numerical simulations is shown. The test results show that the burning behaviour and the fire spreading highly depend on the cable arrangement of the cables on the cable tray, in combination with other boundary conditions. By applying the results as input for a fire simulation, the mass loss rate is considered appropriately.     

Comparison of inward and outward grown Pt modified aluminide diffusion coatings on a Ni based single crystal superalloy

Two commercial Pt modified aluminide coatings (RT22 and MDC150L) on the same single crystal Ni-based superalloy (CMSX-4) were studied by: scanning electron microscopy; transmission electron microscopy; energy dispersive X-ray spectrometry; and gravimetry. The RT22 coating is an inward grown coating (high activity), while MDC150L is produced by outward growth (low activity). Samples were oxidised in still laboratory air at 1050 °C for various times up to 2000 h. It was found that the outward grown coating produced a slower growing oxide that was more spallation resistant. Several possible reasons for this were identified including: coating purity; coating surface topography; and ductile to brittle transition temperature. The microstructural differences between the two coatings in the as-coated condition were investigated and the development of their microstructure during heat treatment was described. A model for coating growth during heat treatment was proposed.     

Continuously distributed phase shifts in chirped DFB lasers usingbent waveguides

The authors have implemented chirped distributed feedback (DFB) grating lasers with phase shifts [λ/8, 2λ/8 and 3λ/8] distributed continuously over various axial distances, using their recently proposed method for producing bent optical waveguides. The singlemode stability of the lasers with distributed phase shifts was found to be considerably higher than for lasers with abrupt phase shifts     

Monolithic integration of DFB laser with spot-size transformer forhighly efficient laser fibre coupling

The monolithic integration of a mushroom type InGaAs-InGaAsP MQW DFB laser with a spot-size transformer based on a two-layer lateral taper is reported. Highly efficient coupling to a butt-joined dispersion shifted singlemode fibre with a coupling loss down to 0.9 dB and large alignment tolerances was achieved, maintaining the good spectral characteristics of an isolated DFB-laser structure     

Continuously chirped DFB gratings by specially bent waveguides fortunable lasers

We have implemented and studied a new type of tunable multiple-section semiconductor distributed feedback (DFB) laser using tailored chirped DFB gratings. Arbitrarily and continuously chirped DFB gratings are defined by bent waveguides on homogeneous grating fields with ultrahigh spatial precision. The mathematical bending functions are optimized in this case to provide enlarged wavelength tuning ranges. We present the results of model calculations, the technological device realization and experimental results of the DFB laser characterization e.g. a tuning range of 5.5 nm without wavelength gaps and high side mode suppression ratio     

A tractable large-signal dynamic model-application to stronglycoupled distributed feedback lasers

The modulation characteristics of DFB semiconductor lasers have been studied using a transfer matrix method combined with an appropriate rate equation analysis. The model takes into account longitudinal mode spatial hole burning, as well as the nonuniform current injection resulting from the axially varying Fermi voltage, and can be used for the efficient simulation of static, small-signal, and large-signal dynamic properties. The program is applied to the interpretation of experimental data from a strongly coupled InGaAsP/InP DFB laser. The experimental high-frequency properties of this device are well described by the simulations     

Electrodynamic headphones and woofers for application in magnetic resonance imaging scanners

Electrodynamic speakers compatible with (functional) magnetic resonance imaging (MRI) are described. The speakers magnets are removed, their function is replaced by the scanner's magnetic field, resulting in an uncommon but efficient operation. The method can be used with headphones as well as woofers. Functional MRI is not associated with any known biological risks, but as a method for visualization of task-specific activation of brain regions it is undesirably noisy. Thus, it requires both noise protection and efficient sound transmission systems for delivering acoustic stimuli to subjects. Woofers could possibly be used in active noise-control systems. The speakers described in this paper can be used for either task.