Pull-Down of Metalloproteins in Their Native States by Using Desthiobiotin-Based Probes

One-third of all proteins are estimated to require metals for structural stability and/or catalytic activity. Desthiobiotin probes containing metal binding groups can be used to capture metalloproteins with exposed active-site metals under mild conditions so as to prevent changes in metallation state. The proof-of-concept was demonstrated with carbonic anhydrase (CA), an open active site, Zn²⁺-containing protein. CA was targeted by using sulfonamide derivatives. Linkers of various lengths and structures were screened to determine the optimal structure for capture of the native protein. The optimized probes could selectively pull down CA from red blood cell lysate and other protein mixtures. Pull-down of differently metallated CAs was also investigated.     

Simulated Microgravity Inhibits the Proliferation of Chang Liver Cells by Attenuation of the Major Cell Cycle Regulators and Cytoskeletal Proteins

Simulated microgravity (SMG) induced the changes in cell proliferation and cytoskeleton organization, which plays an important factor in various cellular processes. The inhibition in cell cycle progression has been considered to be one of the main causes of proliferation inhibition in cells under SMG, but their mechanisms are still not fully understood. This study aimed to evaluate the effects of SMG on the proliferative ability and cytoskeleton changes of Chang Liver Cells (CCL-13). CCL-13 cells were induced SMG by 3D clinostat for 72 h, while the control group were treated in normal gravity at the same time. The results showed that SMG reduced CCL-13 cell proliferation by an increase in the number of CCL-13 cells in G0/G1 phase. This cell cycle phase arrest of CCL-13 cells was due to a downregulation of cell cycle-related proteins, such as cyclin A1 and A2, cyclin D1, and cyclin-dependent kinase 6 (Cdk6). SMG-exposed CCL-13 cells also exhibited a downregulation of α-tubulin 3 and β-actin which induced the cytoskeleton reorganization. These results suggested that the inhibited proliferation of SMG-exposed CCL-13 cells could be associate with the attenuation of major cell cycle regulators and main cytoskeletal proteins.     

Inhomogeneous softening during annealing of ultrafine-grained silver processed by HPT

The softening in ultrafine-grained silver processed by high-pressure torsion (HPT) was studied during annealing using differential scanning calorimetry (DSC). Two separate exothermic peaks were observed in the DSC thermogram of the HPT-processed sample. It is shown that the first and the second peaks are related to the recrystallization of the middle volume and the surface regions of the HPT-processed disk, respectively. Therefore, a very inhomogeneous sandwich-like microstructure develops during annealing with a soft interior and hard surface layers. The lower thermal stability of the middle region appears to be related to the stronger twinning activity since the twinned volumes can act as nuclei for recrystallized grains. The higher twin-fault probability in the interior is attributed to the larger strain due to the outflow of material between the anvils of the HPT facility during quasi-constrained processing.     

Deformation and Fracture of β‐Silicon Nitride Micropillars

Room‐temperature deformation and fracture behaviors under microcompression of single crystal β‐silicon nitride (Si₃N₄) micropillars were investigated. Pillars were fabricated by focused ion beam (FIB) in large Si₃N₄ grains, located close to the basal and prismatic orientations, selected by electron backscatter diffraction (EBSD). The micromechanical test and the damage characterization were performed by nanoindentation and scanning electron microscopy (SEM), respectively. The elastic, plastic, and fracture properties, such as Young's modulus, yield stress, and rupture stress are considerably influenced by the pillar orientation. The activation of the type slip system was identified in case of basal oriented micropillars.     

Cognitive amplify‐and‐forward relay networks with beamforming under primary user power constraint over Nakagami‐m fading channels

In this paper, we analyze the performance of cognitive amplify‐and‐forward (AF) relay networks with beamforming under the peak interference power constraint of the primary user (PU). We focus on the scenario that beamforming is applied at the multi‐antenna secondary transmitter and receiver. Also, the secondary relay network operates in channel state information‐assisted AF mode, and the signals undergo independent Nakagami‐m fading. In particular, closed‐form expressions for the outage probability and symbol error rate (SER) of the considered network over Nakagami‐m fading are presented. More importantly, asymptotic closed‐form expressions for the outage probability and SER are derived. These tractable closed‐form expressions for the network performance readily enable us to evaluate and examine the impact of network parameters on the system performance. Specifically, the impact of the number of antennas, the fading severity parameters, the channel mean powers, and the peak interference power is addressed. The asymptotic analysis manifests that the peak interference power constraint imposed on the secondary relay network has no effect on the diversity gain. However, the coding gain is affected by the fading parameters of the links from the primary receiver to the secondary relay network. Copyright © 2012 John Wiley & Sons, Ltd.     

Multiphase coatings from complex radiation curable polyurethane dispersions

The waterborne nature of radiation curable polyurethane dispersions largely respond to the current environmental concerns and do not require any additional coalescent since the film formation (drying) and hardening (photo-curing) take place in distinct steps. It is possible to design aqueous dispersions with distinct polymer particle populations resulting in micro-structured coatings with optimized properties over a wide range of curing conditions. Mixed dispersions based on hard and soft acrylated polyurethane particles were used as model systems for the present study. The minimum film formation temperature has been investigated as a function of the hard:soft polymer ratio. The elastic modulus of the dry coatings shows a reinforcing effect consistent with the inclusion of hard domains in a soft continuous matrix. However, the level of reinforcement is not properly predicted by the usual mechanical models and it is qualitatively accounted for by assuming a composition gradient (interphase) between the hard domains and the matrix. The multiple-phase structure was clearly established by Atomic Force Microscopy in agreement with thermal analysis data. Furthermore the local nanoscale mechanical properties were mapped using a new imaging mode based on real-time force–distance curve analysis. Finally, the coatings prepared using this multiple-phase pattern present a clear benefit over conventional homogeneous coatings by offering an improved balance of chemical and mechanical resistance in pigmented systems applied on melamine-coated MDF panels.     

Electrical aging of extruded dielectric cables: review of existingtheories and data

Despite the huge amount of data on so-called electrical aging of extruded HV cables, the fundamental phenomena responsible for it or evolving with aging time, are still far from well understood. It is therefore not surprising why it is so difficult to predict reliable cable lifetimes in service from accelerated aging experiments in the laboratory. The objective of this paper is to review critically the existing theories of electrical aging of solid dielectric materials. A relatively large number of models and theories exist but none of the most often used is known to yield reliable life predictions. One conclusion is that there is a need for a more comprehensive model of electrical aging of extruded dielectric cables. In order to develop this model, an extensive review of existing literature data was undertaken. This paper summarizes the data collected from more than 200 papers on aging of PE, XLPE and EPR cables. It appears that cable breakdown strength should not be plotted on log field vs. log time graphs to yield long-time (i.e. low-field) values, since results obtained over a long time period do not obey an inverse power law. In fact, high-field results are better described by an exponential relation between time and field. The models of Simoni, Montanari and Crine seem to give the best fit to experimental results obtained under a wide variety of experimental conditions. It is also shown that the lower field limit for the exponential regime with XLPE cable is in the 8 to 15 kV/mm range, which corresponds to the onset of strong charge injection. The influence of environment, insulation nature and morphology, and testing temperature are discussed     

Load Bearing Capacity of Reinforced Concrete Beams Subjected to Dynamic Cyclic Loads

A kinematic method is developed to determine the shakedown limits of elastic-perfectly plastic steel-reinforced concrete beams under quasi-static and dynamic cyclic loads. This procedure, like the respective kinematic approach of plastic limit analysis, is visual and easy to use in engineering applications. The load parameters (amplitudes, frequency) versus yield moment diagrams, constructed from possible collapse modes, should assist in choosing the reinforcement scheme and amounts of reinforcement to meet the load bearing requirements for the structures.     

Correlation between microstructure and mechanical properties of severely deformed metals

There is a correlation between the microstructure and the mechanical behavior of ultrafine-grained face centered cubic (fcc) metals processed by equal-channel angular pressing (ECAP). It is shown that the saturation yield strength is related to the maximum dislocation density according to the Taylor equation and, in addition, the value of the parameter α in the Taylor equation is strongly affected by the stacking fault energy because of different geometrical arrangements of dislocations within the grains. It is also demonstrated that the ductility of Cu processed by ECAP decreases with increasing strain but at extremely high strains the ductility is partially restored due to the recovery of the microstructure.     

Threshold stress in dispersionally strengthened superplastic Al alloys

It is important for practical applications that some commercial alloys with stabilized finegrained structure should exhibit superplastic behaviour at high temperatures. In this paper the results of impression creep tests conducted on AlMgZn alloys are reported and the strain rate sensitivity and activation enthalpy were determined. The mechanical behaviour of the alloys as a function of the strain rate sensitivity can be divided into three regions. At low and high stresses the strain rate sensitivity parameter is low and the deformation process is not superplastic. Superplastic deformation takes place only at intermediate stresses. The microstructural interpretation of these processes involves, in general, the change of the micromechanisms controlling the different deformation processes. It was determined that by the supposition of a threshold stress depending strongly on temperature, the two regions due to low and intermediate stresses of the deformation can be described by the same constitutive equation.