Ultra-wideband bandpass filter with hybrid microstrip/CPW structure

A novel ultra-wideband (UWB) bandpass filter (BPF) is presented using the hybrid microstrip and coplanar waveguide (CPW) structure. A CPW nonuniform resonator or multiple-mode resonator (MMR) is constructed to produce its first three resonant modes occurring around the lower end, center, and higher end of the UWB band. Then, a microstrip/CPW surface-to-surface coupled line is formed and modeled to allocate the enhanced coupling peak around the center of this UWB band, i.e., 6.85GHz. As such, a five-pole UWB BPF is built up and realized with the passband covering the entire UWB band (3.1-10.6GHz). A predicted frequency response is finally verified by the experiment. In addition, the designed UWB filter, with a single resonator, only occupies one full-wavelength in length or 16.9mm.     

Enzymatic degradation of thermoresponsive poly(N‐isopropylacrylamide) grafted to carboxymethylcellulose copolymers

The enzymatic degradation of poly(N‐isopropyl acrylamide) (PNIPAM) grafted to carboxymethylcellulose (CMC) copolymers with a cellulasic preparation (Trichoderma viride) was studied. The enzymatic activity of the cellulasic preparation against CMC and the grafted copolymers was determined by the Petterson–Porath method, while their reduced viscosity variation in the presence of the same preparation was also followed. It has been shown that the enzymatic degradation behavior depends on the copolymer composition and the reaction temperature. Reducing sugars analysis showed that the experimental values for the grafted copolymers were higher than the calculated ones. At 50°C, the enzymatic reaction is completed in about 20 min for the copolymers, whereas for CMC it takes more than 40 min. It can be concluded that their enzymatic degradation is facilitated by the presence of the PNIPAM grafts. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1383–1386, 2003     

Compatibilisation of PPE/SAN blends by triblock terpolymers: Correlation between block terpolymer composition, morphology and properties

Immiscible blends of poly(2,6-dimethyl-1,4-phenylene ether) (PPE) and poly(styrene-co-acrylonitrile) (SAN) with a weight composition of 60/40 were compatibilised by polystyrene-block-polybutadiene-block-poly(methyl methacrylate) triblock terpolymers (SBM) using a two-stage melt-processing approach. In order to investigate the influence of the SBM composition on the compatibilisation efficiency, the block lengths of the triblock terpolymers were systematically varied. The resulting morphological features of the blend systems as function of SBM composition and processing parameters are correlated with the resulting thermal and thermo-mechanical properties. In the ideal case, SBM should be located at the interface as PS is miscible with PPE while PMMA is miscible with SAN. The elastomeric middle block as an immiscible component should remain at the interface. This particular morphological arrangement is known as the ‘raspberry morphology’. A detailed TEM analysis of the blend morphologies following initial extrusion-compounding revealed a high compatibilisation efficiency of the SBM types with equal lengths of the end blocks and, furthermore, the desired raspberry morphology was achieved. In contrast, high PS contents in comparison to the other blocks led to a pronounced micelle formation in the PPE phase. Further evaluation of the blend structures following injection-moulding indicated that the morphologies remain relatively stable during this second melt-processing step. A detailed thermal analysis of all blend systems supports the interpretation of the observed morphological features. The fundamental correlation between SBM composition and blend morphology established in this study opens the door for the controlled development of interfacial properties of such compatibilised PPE/SAN blends during melt-processing.     

Towards long term monitoring of electrodermal activity in daily life

Manic depression, also known as bipolar disorder, is a common and severe form of mental disorder. The European research project MONARCA aims at developing and validating mobile technologies for multi-parametric, long term monitoring of physiological and behavioral information relevant to bipolar disorder. One aspect of MONARCA is to investigate the long term monitoring of Electrodermal activity (EDA) to support the diagnosis and treatment of bipolar disorder patients. EDA is known as an indicator of the emotional state and the stress level of a person. To realize a long-term monitoring of the EDA, the integration of the sensor system in the shoe or sock is a promising approach. This paper presents a first step towards such a sensor system. In a feasibility study including 8 subjects, we investigate the correlation between EDA measurements at the fingers, which is the most established sensing site, with measurements of the EDA at the feet. The results indicate that 88% of the evoked skin conductance responses (SCRs) occur at both sensing sites. When using an action movie as psychophysiologically activating stimulus, we have found weaker reactivity in the foot than in the hand EDA. The results also suggest that the influence of moderate physical activity on EDA measurements is low and has a similar effect for both recording sites. This suggests that the foot recording location is suitable for recordings in daily life even in the presence of moderate movement.     

Flank milling with flat end milling cutters

One situation encountered in industry is that two curves on the machined surface are known, such as the top and bottom profiles of a blade. The shape of the surface is not known and is to be determined by a tool sliding along the generating rails. In this paper, we give a detailed mathematical understanding of flank milling with flat end cutters, which we then use to develop a method for milling with such a cutter. This method slides the cutter along two rails, keeping the cutter tangent to both curves at every parameter value. Examples are given to illustrate the method, along with simulations and error analysis.     

Towards Perceptual Simplification of Models with Arbitrary Materials

Real‐time rendering of models with high polygon count is still an important issue in interactive computer graphics. A common way to improve rendering performance is to generate different levels of detail of a model. These are mostly computed using polygonal simplification techniques, which aim to reduce the number of polygons without significant loss of visual fidelity. Most existing algorithms use geometric error bounds, which are well‐suited for silhouette preservation. They ignore the fact that a much more aggressive simplification is possible in low‐contrast areas inside the model. The main contribution of this paper is an efficient simplification algorithm based on the human visual system. The key idea is to move the domain of error computation from image‐space to vertex‐space to avoid a costly per‐pixel comparison. This way the error estimation of a simplification operation can be accelerated significantly. To account for the human vision, we introduce a perceptually based metric depending on the contrast and spatial frequency of the model at a single vertex. Finally, we validate our approach with a user study.