Feasibility of the indirect determination of blast-induced rock movement based on three new hybrid intelligent models

Engineering with Computers - The indirect and accurate determination of blast-induced rock movement has important significance in the reduction of ore loss and dilution and in the protection of...     

体系对抗条件下红外导引头探测系统建模与仿真

分析了红外导引头探测系统的设计要求,建立了仿真系统的体系结构,描述了各子模块的功能、组成、模型原理,最后在基于组件的一体化建模仿真环境(CISE)下给出了红外导引头探测系统的仿真实现。体现了实战要素对探测系统的影响,为体系对抗条件下红外导引头的建模仿真提供了参考。     

浅谈机床领域的电磁干扰问题

阐明电磁干扰问题一直是技术人员在机床调试、维修过程中经常遇到的问题.介绍了提高机床电气系统抗干扰的措施以及在实际的机床调试、维修过程中遇到的故障举例及解决方案.     

Brush-type amphiphilic polystyrene-g-poly(2-(dimethylamino)ethyl methacrylate)) copolymers from ATRP and their self-assembly in selective solvents

A series of well-defined brush-type amphiphilic polystyrene-g-poly(2-(dimethylamino) ethyl methacrylate)) (PS-g-PDMAEMA) copolymers were successfully synthesized via atom transfer radical polymerization (ATRP), using chloromethylated polystyrene (CMPS) as the macroinitiator. The self-assembly behavior of the resulting brush-type copolymers in deionized water and deionized water/acetone (v/v=2/3) mixture was studied by high performance particle sizer (HPPS). The results showed that the Z-average size of the micelles in deionized water increased with the increase of molecular weight of PDMAEMA, and the corresponding size was larger than that in mixed solvent of deionized water and acetone (v/v=2/3). The morphologies of the micelles self-assembled from PS-g-PDMAEMA in selective solvents were studied by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). When the micelles were prepared in water/acetone (v/v=2/3) mixture and cast them on a glass slide at different temperatures (from 50 up to 200 °C), the transformation of the morphologies of aggregates, from needle-like solid to microcubic particles, was observed using SEM.     

超低功耗井下监测仪器设计

通过对常见集成电路工作模式及其功耗的分析；提出一种适合在油井下工作的超低功耗数据采集系统的设计方法。由于降低了系统功耗，因此，不需要电缆供电就可以在不影响正常生产的情况下完成对油井生产过程的动态监测。此餐，该设计方法将看门狗监控电路与降低功耗结合在一起，在降低系统功耗的同时提高了系统可靠性。实验说明，该系统在断续工作状态下也能正常采集数据。最后，给出了一个实际系统在各种没荼模式下的实际工作电流值。     

数控化改造外圆磨床砂轮成形修整的应用

介绍了基于国产经济型开通数控系统改造的数控外圆磨床MKA1320/H的方法,针对数控外圆磨床复杂曲面砂轮的成形修整问题进行研究,通过开通数控开放式编程环境,完成了砂轮成形修整的数控编程,最后给出了完整程序。     

UO2-(Zr0.8Ca0.2)O1.8面心立方固溶体微球制备工艺研究

为研制出耐辐照的新型单相陶瓷燃料,采用溶胶-凝胶法,通过复合溶胶配制、分散胶凝、洗涤、干燥煅烧与烧结过程,开展了UO2-(Zr0.8Ca0.2)O1.8燃料微球制备工艺研究,制备出铀摩尔分数含量分别为30mol%、50mol%、70mol%的UO2-(Zr0.8Ca0.2)O1.8燃料微球样品。在对工艺过程进行分析的基础上,通过实验确定了工艺参数。采用X射线衍射（XRD）对3种燃料微球样品进行分析,分析结果表明:铀摩尔分数含量分别为30mol%、50mol%、70mol%的UO2-(Zr0.8Ca0.2)O1.8燃料微球样品均为面心立方（FCC）固溶体结构。      

基于超高频检测技术研究GIS中的局部放电

根据气体绝缘的金属封闭式组合电器(GIS)的波导结构及局部放电脉冲所激发的电磁波的宽频带特征,建立了外部天线超高频局部放电检测系统。利用该系统对252kVGIS母线段中相同气压、不同电压超高频下固定微粒局部放电模型进行检测,并借助联合时频分析方法对信号进行处理。结果表明,外部天线超高频局部放电检测系统可以实现GIS局部放电检测,固定微粒局部放电频谱特征明显。