Analyzing the determinants of carbon emissions from transportation in European countries: the role of renewable energy and urbanization

Clean Technologies and Environmental Policy - The continuous growth of transport sector and the increase in carbon emissions from transportation attract the attention of policy makers in...     

HYDRODYNAMIC STUDIES IN A HALF SLOT-RECTANGULAR SPOUTED BED COLUMN

Experiments were carried out in a half slot-rectangular spouted bed to investigate the effects of slot width and lower section basal angle on column hydrodynamics. Flow regimes, minimum spouting velocity, spouting and maximum pressure drops, and maximum spoutable bed height were determined for 4 mm diameter polyethylene particles. The results are compared with those for conventional cylindrical and rectangular spouted beds. Correlations for each hydrodynamic parameter are developed and compared with equations available in the literature.     

A path planning model based on nested regular hexagons using weighted centroid localization

In many wireless sensor network (WSN) applications, the location of a sensor node is crucial for determining where the event or situation of interest occurred. Therefore, localization is one of the critical challenges in WSNs. Mobile anchor node assisted localization (MANAL) is one of the promising solutions for the localization of statically deployed sensors. The main problem in MANAL localization is that the path planning of the mobile anchor (MA) node should be done so that the localization error in the network will be minimal and that all unknown nodes in the network are covered. This paper proposes a new path planning approach called nested hexagons curves (NHexCurves) for MANAL. NHexCurves guarantees that it will receive messages from at least three non-collinear anchors to locate all unknown nodes in the network. The proposed model has compared six different path planning schemes in the literature using weighted centroid localization (WCL). In these comparisons, first of all, localization errors of the models are compared using some statistical concepts. Second, the variation of the localization error according to parameters such as resolution (R) and the standard deviation of noise (σ) is observed. Then, with similar approaches, the standard deviation of errors, localization ratio, scalability performances, and finally, path lengths of the models are examined. The simulation results show that the NHexCurves static path planning model proposed in this study stands out compared to other models with high localization error and localization ratio performance, especially at low resolutions, due to its path design. At the same time, the lowest error values according to σ are obtained with the proposed model among all models considered.     

Electrophoretic deposition of nano-sized BaTiO3

In this study, a non-aqueous method in a simple one pot reaction process was employed to synthesize nano-sized BaTiO₃ particles and then electrophoretic deposition technique was employed for thin film coatings. In the first step of the preparation, metallic barium is directly dissolved in benzyl alcohol at slightly elevated temperatures. Then titanium isopropoxide was added following by a solvothermal treatment. At the end of the reaction, nearly spherical BaTiO₃ nanoparticles were obtained typically 5 nm in diameter. After establishing the stability of the BaTiO₃ suspension in ethanol, electrophoretic deposition process was performed without any additional operation. Alumina with platinum plating was used as substrate. To achieve the optimal process parameters, various voltages were applied by altering the cathode to anode distance as well as deposition time. High voltages application was possible without causing hydrolysis, because of the non-aqueous ethanol medium with higher surface charge of the nanoparticles. The deposited surface coatings were dried in air and sintered at various temperatures. SEM, EDX and XRD analysis were employed for the investigation of the coating.     

Investigation of the Equivalence of National Dew-Point Temperature Realizations in the ?50?°C to +?20?°C Range

In the field of humidity quantities, the first CIPM key comparison, CCT-K6 is at its end. The corresponding European regional key comparison, EUROMET.T-K6, was completed in early 2008, about 4?years after the starting initial measurements in the project. In total, 24 NMIs from different countries took part in the comparison. This number includes 22 EURAMET countries, and Russia and South Africa. The comparison covered the dew-point temperature range from ?50?°C to +20?°C. It was carried out in three parallel loops, each with two chilled mirror hygrometers as transfer standards in each loop. The comparison scheme was designed to ensure high quality results with evenly spread workload for the participants. It is shown that the standard uncertainty due to the long-term instability was smaller than 0.008?°C in all loops. The standard uncertainties due to links between the loops were found to be smaller than 0.025?°C at ?50?°C and 0.010?°C elsewhere. Conclusions on the equivalence of the dew-point temperature standards are drawn on the basis of calculated bilateral degrees of equivalence and deviations from the EURAMET comparison reference values (ERV). Taking into account 16 different primary dew-point realizations and 8 secondary realizations, the results demonstrate the equivalence of a large number of laboratories at an uncertainty level that is better than achieved in other multilateral comparisons so far in the humidity field.     

UV curable lens production using molecular weight controlled PEEK based acrylic oligomer (Ac-PEEK)

We produced UV curable lenses with properties blocking short wave UV light. In the UV-curable formulations, we used an oligomer (Ac-PEEK) with another urethan oligomer (Mw = 2000). Radically active, molecular weight controlled Ac-PEEK was obtained by reacting 2-hydroxyl ethyl methacrylate with molecular- weight- controlled and isocyanate terminated PEEK (Mn = 4500). We characterized all synthesized monomer, oligomer and optical materials with UV/Vis spectrophotometer with interferogram, elemental analyser, mass spectrophotometer, proton nuclear magnetic resonance, Fourier transform infrared spectroscopy, thermal gravimetric analyzer, differential scanning calorimeter, scanning electron microscopy and gas chromatography. Results suggested that newly synthesized oligomer with the structure of PEEK absorbs short wave UV-light. Ageing tests [ISO 11979-5, Ophthalmic implants—intraocular lenses (IOL)—Part 5: Biocompatibility] performed on the IOL materials were successful. High contact angle of the obtained lenses suggests that all lenses were hydrophobic and SEM results revealed that lenses are morphologically homogeneous. Based on all positive properties just mentioned, we safely conclude that the lenses produced in this study are very promising for IOL production.     

Composition dependences of thermodynamical properties associated with Pb-free ternary,quaternary, and quinary solder systems

In the present study, Chou’s General Solution Model (GSM) has been used to predict the enthalpy and partial enthalpies of mixing of the liquid Ag–In–Sn ternary, Ag–In–Sn–Zn quaternary, and Ag–Au–In–Sn–Zn quinary systems. These are of technical importance to optimize lead-free solder alloys, in selected cross-sections: x_In/x_Sn = 0.5/0.5 (ternary), Au–In_0.1–Sn_0.8–Zn_0.1, Ag–In_0.1–Sn_0.8–Zn_0.1 (quaternary), and t = x_Au/x_In = 1, x_In = x_Sn = x_Zn (quinary) at 1173, 773, and 773 K, respectively. Moreover, the activity of In content in the ternary alloy system Ag–In–Sn has been calculated and its result is compared with that determined from the experiment, while the activities of Ag contents associated with the alloys mentioned above have been calculated. The other traditional models such as of Colinet, Kohler, Muggianu, Toop, and Hillert are also included in calculations. Comparing those calculated from the proposed GSM with those determined from experimental measurements, it is seen that this model becomes considerably realistic in computerization for estimating thermodynamic properties in multicomponent systems.