A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Fault section detection system for 66 kV underground branchtransmission lines using optical magnetic field sensors

A fault section detection system that uses optical magnetic field sensors and instantly detects the section in which a ground fault occurred was developed for 66 kV underground multiterminal systems having Y-branch joint boxes. The optical magnetic field sensor, which is based on the Faraday effect in Bi-doped YIG ((BiYbGd)₃Fe₅O₁₂) having a large Verdet constant, detects cable conductor currents of 0 to 2000 A with high precision with the use of a laminated magnetic ring core of silicon steel plates. Sensors and a fault section detector/indicator of a system are connected with optical fibers capable of nonrepeated transmission of over 6 km     

A Fuzzy Expert System for Damage Assessment Using Genetic Algorithms and Neural Networks

Abstract: An efficient knowledge-acquisition support method is required for improvement and maintenance of the knowledge base in durability evaluation of an RC bridge deck. Such a method is proposed in this paper to automatically acquire fuzzy production rules. This method makes joint use of genetic algorithms and a neural network. Using a neural network as a subsystem, the evaluation function of genetic algorithms can be provided with the weights of the neural network. Introducing a neural network into genetic algorithms, it is possible to acquire new knowledge so that the method is useful when it is difficult to acquire knowledge in the field.     

Accumulation of amplified target DNAs using thiol/biotin labeling, S1 nuclease, and ferrocene-streptavidin-magnetic system and a direct detection of specific DNA signals with screen printed gold electrode

Combinations of PCR-based amplification platform using 5′ thiolated and biotinylated specific primers, S1 nuclease-PCR products treatment, ferrocene-streptavidin (Fc-Stv)-magnetic binding for DNA accumulation, and screen printed gold electrode for the DNA allocation, were applied to Hoechst 33258-induced DNA aggregation and signals induction system for direct signals detection and DNA quantification in food samples. Thiolated and biotinylated at each 5′ terminus enabled DNA purification through S1 nuclease treatment for primers and non-specific DNA elimination and enabled DNA trapping with a ferrocene-streptavidin-magnetic system. This facilitated the accumulation of target DNAs at higher concentration, resulting in enhanced signals. After allocation of DNA on the surface of gold electrode via thiol binding, intensity of DNA signals through these treatments could be measured directly after being induced by Hoechst 33258. Wider amplitude changes in anodic current peaks between negative and positive samples (increasing from 3.70 to 10.10 μA) compared with those applied with no treatment combinations (decreasing from 3.92 to 1.23 μA) were observed. This enhancement of the signals allowed a greater efficiency of DNA quantification. When this combination was used for GMOs content estimation in reference samples, results revealed an improved accuracy from 66% to 96%. The combined biosensor system, although more costly than the standard Hoechst 33258/carbon electrode system, provided an alternative choice for DNA quantification, offering labor-free immobilization of probe onto electrode surface, easy test administration, and efficient semi-quantitative test without expensive instruments.     

Yttria Doping and Sintering of Submicrometer-Grained α-Alumina

The sintering behavior of α-alumina powders doped with magnesia (500 or 1500 ppm) and yttria (0, 500, or 1500 ppm) was investigated using constant-heating-rate dilato-metric experiments. The apparent activation energies for the intermediate stage of sintering were 740, 800, and 870 kJ/mol for 0, 500, and 1500 ppm yttria doping levels, respectively; these were independent of magnesia doping. Yttria-doped powder compacts exhibited systematic anomalous second peaks in the densification rate curves at certain grain sizes which were determined only by yttria doping levels. Before the anomalous peak, with lower yttrium contents at grain boundaries, yttrium in an atomic state delays densification and raises the apparent activation energy. Beyond the peak, with higher yttrium contents at grain boundaries, yttria-rich precipitation delays the densification. Within the peak, yttrium segregation near the saturation level enhances densification.     

Soft-decision Viterbi decoding with diversity combining formulti-beam mobile satellite communication systems

Diversity combining methods for mobile satellite communication systems employing convolutional encoding and soft-decision Viterbi decoding are evaluated. Computer simulation clarifies that the pre-Viterbi-decoding maximal ratio combining method has better performance than other methods in Rician fading channels. The simulation results agree with the Pe (bit error probability) performance derived from the numerical analysis for slow fading using the approximate Pe performance of Viterbi decoding in AWGN (additive white Gaussian noise) channels and the probability density function of Rician fading. Applying this diversity method to the multi-beam mobile satellite communication systems, a satellite beam diversity reception scheme is proposed. A computer simulation result shows that the proposed scheme decreases the packet error rate of the control signals to less than 1/100 around the satellite beam boundary     

Complexity of the color appearance of objects with nonuniform illumination

An inversion relationship is clarified between lightness and brightness, and also between chroma and colorfulness under nonuniform illumination with different illuminance levels (high and low) within the same visual field. Brightness (or colorfulness) of object color with low lightness (or chroma) under high illuminance level is perceived higher than that of another object color with high lightness (or chroma) under low illuminance level. Two color images are given for showing the inversion phenomena on brightness–lightness and colorfulness–chroma between object colors under different illuminance levels. These color images are useful for making researchers on color understand the differences in concept between brightness and lightness, and also between colorfulness and chroma. In particular, the concept of colorfulness is important, but difficult to understand. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 372–377, 2007