Physicochemical and technological properties of beef burger as influenced by the addition of pea fibre

This study aimed to evaluate the physicochemical characteristics and sensory attributes of beef burgers with the addition of pea fibre as a partial substitute of meat or fat. Three formulations were prepared: control (CON) – similar to the commercial formulation; fibre/less meat (FLM)—5% meat reduction and addition of 1% pea fibre; fibre/less fat (FLF)—7% fat reduction and addition of 1% pea fibre. Non-significant differences were obtained for pH, colour parameters (L* and b*), texture profile, cooking loss and size reduction among formulations. Moreover, sensory analysis with consumers of beef burgers did not indicate differences among the formulations for all the analysed attributes. Therefore, pea fibre is a promising partial replacer for meat and fat in beef burgers due to the preservation of technological parameters and sensory acceptance.     

A simple model for the semicontinuous heterophase polymerization: Ethyl methacrylate as a case example

A simple but comprehensive model considering homogeneous and micellar nucleation, coagulation, entry of radicals to particles and to micelles and radicals' exit from particles, is presented. The model is validated, in a starved semicontinuous heterophase polymerization of ethyl methacrylate, at three monomer addition rates. The model accurately describes the overall and instantaneous conversion, the average particle density and diameter, and the number and weight average molar masses evolutions over time. It is found that even though the average number of radicals is much smaller than 0.5, the system is not 0-1. An empirical function was used to describe the gel effect. The homogeneous nucleation was the prevailing mechanism for particle formation and large exit rates of radicals were observed. POLYM. ENG. SCI., 60: 223–232, 2019. © 2019 Society of Plastics Engineers     

Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.     

Nanocrystalline TiO2 photosensitized with natural polymers with enhanced efficiency from 400 to 600 nm

TiO₂ sensitization for solar applications requires not only efficient but also stable and inexpensive sensitizers. Different condensed tannins extracted from bark wastes of tropical wood trees were studied as possible sensitizers of TiO₂. These natural polymers adhere strongly to the TiO₂ even from aqueous solutions. Absorption spectra are presented for 1 mM aqueous sensitizing solutions prepared with lyophilized condensed tannins which absorb light in the visible range. Spectral photocurrent measurements and I–V characterization show that no bias is required for electron injection to the TiO₂ from all studied condensed tannins. Incident photon to current efficiency (IPCE) analysis indicates that surface complexation originates absorption bands with different electron injection efficiencies. These play a dominant role in determining IPCE spectral shape. We propose that surface modification by the sensitizer changes the surface trap density, thereby decreasing recombination losses.     

Composing RESTful Services and Collaborative Workflows: A Lightweight Approach

The use of RESTful Web services has gained momentum in the development of distributed applications based on traditional Web standards such as HTTP. In particular, these services can integrate easily into various applications, such as mashups. Composing RESTful services into Web-scale workflows requires a lightweight composition language that's capable of describing both the control and data flow that constitute a workflow. The authors address these issues with Bite, a lightweight and extensible composition language that enables the creation of Web-scale workflows and uses RESTful services as its main composable entities.