Effects of breed and age at slaughter on degradation of muscle lipids during processing of dry‐cured hams

Hams from Landrace, Duroc and Hampshire pigs slaughtered at ages 6, 7.5 and 9 months were processed to generate Norwegian Parma‐style hams. Lipid contents and the compositions of fatty acid classes (ΣSFA, ΣMUFA, ΣPUFA) within neutral lipids, phospholipids and free fatty acids were determined. Small differences in lipid degradation and composition of the classes were revealed. However, significant sensory differences related to lipids were observed. Breed was more important than age. Dry‐cured Hampshire hams gave a more intense mature odour that may be associated with higher overall lipid degradation. Unexpectedly, these hams also demonstrated high juiciness and tenderness, which could be related to the melting characteristics of the fat. Dry‐cured Duroc hams showed a higher susceptibility towards rancidity, presumably associated with preferential oxidation of n‐6 fatty acids relative to C18:1 n‐9. Dry‐cured Landrace hams showed the lowest juiciness and tenderness, likely due to their lower fat content (marbling).     

On the effects of the packet size distribution on the packet loss process

Real-time multimedia applications have to use forward error correction (FEC) anderror concealment techniques to cope with losses in today’s best-effort Internet. The efficiency of these solutions is known however to depend on the correlation between losses in the media stream. In this paper we investigate how the packet size distribution affects the packet loss process, that is, the distribution of the number of lost packets in a block, the related FEC performance and the average loss run length. We present mathematical models for the loss process of the MMPP+M/D/1/K and the MMPP+M/M/1/K queues; we validate the models via simulations, and compare the results to simulation results with an MPEG-4 coded video trace. We conclude that the deterministic packet size distribution (PSD) not only results in lower stationary loss probability than the exponential one, but also gives a less correlated loss process, both at a particular average link load and at a particular stationary loss probability as seen by the media stream.Our results show that for applications that can only measure the packet loss probability, the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior. Our results show that the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior and thus can improve the queuing performance by decreasing the variance of its PSD.     

A comparison between different PMD compensation techniques

We quantify the benefits of using different techniques for compensation of polarization mode dispersion (PMD) in fiber-optic communication systems by means of numerical simulations. This is done both with respect to PMD-induced pulse broadening and in terms of system outage probability for different data formats [nonreturn-to-zero (NRZ) and return-to-zero (RZ)]. Attention is focused on simple and relevant single- and double-stage post-transmission compensators with a few degrees of freedom (DOF). It is generally believed that a PMD compensator with a polarization controller and a variable delay line can only compensate the PMD to the first order. We show, from analytical results, the counterintuitive fact that this scheme can also partially compensate for higher order PMD. We also investigate the benefit of using a polarizer as compensation element where the optical average power can be used as a feedback signal     

Tensile,creep, and low-cycle fatigue behavior of a cast γ-TiAl-based alloy for gas turbine applications

The influence of chemical composition on the microstructure of the γ-titanium aluminide alloy Ti-48Al-2W-0.5Si (at. pct) and the accompanying tensile, low-cycle fatigue, and creep properties has been evaluated. The study showed that small variations in chemical composition and casting procedures resulted in considerable variations in the microstructure, yielding vastly different mechanical properties. Low contents of aluminum and tungsten led to a coarse-grained lamellar (γ/α ₂) microstructure with high creep resistance. A composition close to the nominal one produced a duplex (γ+γ/α ₂) structure with favorable strength, ductility, and low-cycle fatigue properties. By controlling the solidification and cooling rates at casting, a pseudoduplex (PS-DP) microstructure with a unique combination of high strength and high fatigue and creep resistance can be obtained. These unique properties can be explained by the diffuse boundaries between the relatively small γ grains and the neighboring lamellar colonies, combined with semicoherent interfaces between the γ and α ₂ phases. At tensile and low-cycle fatigue loading, these boundaries act like high-angle boundaries, producing a virtually fine-grained material promoting strength, whereas at creep loading, grain-boundary sliding is hindered in the semicoherent interfaces leading to high creep resistance.     

Space-time finite elements for a simplified thermo-metallurgical problem relevant to casting

The non-linear thermo-metallurgical problem, relevant for the cooling of a molten metal including the macro-segregation that occurs during the cooling process, is studied here. Due to the strong non-linearities involved in phase transformations, it is necessary to use a fine resolution in space-time in a finite element approximation in order to meet accuracy requirements. We derive space-time FE-methods based on the discontinuous and continuous Galerkin method in time for the energy equation. This formulation integrates the stored energy exactly for a given heat flux. When macro-segregation is incorporated into the model, the problem can be formulated in such a way that the phase-transition drives a flow of species. In addition, diffusion is possible throughout the domain. The model can be further rewritten using a potential approach. By this approach for modelling macro-segregation, we are able to obtain discretizations that guarantee that the balance equations are satisfied, and it is possible to solve the phase-transition problem either as a field problem or as a local problem (defined by a local evolution rule).     

Optimization of metal-based multilayers for transparent heat mirrors

Multilayer calculations by conventional matrix methods for dielectricum/noble metal/dielectricum systems on glass have been performed. The aim has been to maximize the integrated parameters for solar transmission, T_sol, and transmission of visible light, T_eye We have found that Ag is superior for maximizing the transmittance over the narrow visible wavelength range owing to the low internal absorptance. When solar energy transmission is considered multilayers based on Au are the best choice for metal film thicknesses above 15 nm. For thinner films, Ag is still to be preferred.     

Parameter extraction for bipolar transistors

Different methods of extracting the DC Gummel-Poon bipolar transistor model parameters are reviewed. First the shortcomings of the classical extraction schemes for the intrinsic model are presented together with some improved procedures. Finally the extraction of the series resistances is addressed.