Microwave hybrid fast sintering of red clay ceramics

This work aimed to examine the performance of the hybrid sintering of clay ceramic in a microwave furnace, compared to the sintering process in a conventional furnace. The raw materials were subjected to X-ray fluorescence, loss on ignition (LOI), X-ray diffraction, particle size distribution, real specific mass, and thermogravimetric analyses. The red clay ceramic mass was prepared, extruded, pre-sintered in a conventional furnace at 600°C/60 min, and sintered at temperatures between 700 °C and 1100 °C. The sintering conventional (resistive oven) was carried out for 60 min with a heating rate of 10°C/min. In the microwave furnace, the sintering times were 5, 10, and 15 min, with a heating rate of 50°C/min, with a sintering chamber coated with silicon carbide (susceptor). The sintered specimens were characterized according to linear shrinkage, water absorption, apparent porosity, apparent specific mass, X-ray diffraction, Raman spectroscopy analysis, spectroscopy analysis in the ultraviolet and visible regions, microhardness, and scanning electron microscopy. The results showed that microwave sintering promoted an increase in the microhardness and apparent specific mass, and reduction in water absorption and apparent porosity values, due to greater densification in the microstructure. The best results occurred for specimens sintered at 1100°C.     

Synergistic antimicrobial effect of lactocin AL705 and nisin combined with organic acid salts against Listeria innocua 7 in broth and a hard cheese

The effectiveness of antimicrobial mixtures against Listeria innocua 7, used as a L. monocytogenes surrogate, was investigated in broth and a food system. Synergistic effects were found for nisin (Nis), potassium sorbate (PS), calcium propionate (CP) and sodium lactate (SL), Nis + PS being the most effective binary mixture that exhibited listericidal activity in broth. To assess the effect of adding lactocin AL705 (AL705) to Nis + organic acid salt combinations, tridimensional isobolograms were generated. Sub-MIC combinations of the antimicrobials exerted bactericidal activity against L. innocua 7 after AL705 addition to the binary mixtures. However, when applied on Sardo cheese contaminated with L. innocua 7 (initial inoculum 4.45 ± 0.06 CFU g⁻¹), only Nis + PS + AL705 produced count reductions respect to the control, reaching 3.04 ± 0.35 CFU g⁻¹ counts after 15 days at 15 °C. Ternary combinations containing AL705 showed potential to reduce antimicrobial usages for L. innocua 7 inhibition.     

Doped silicon and NIS junctions for bolometer applications

We discuss the performance, of a normal metal hot electron bolometer (NHEB) that we have measured at 0.3 K. We found that the noise equivalent power was limited by the amplifier noise. To improve the NHEB power response and to make it more robust and reliable we propose to substitute the normal metal with heavily doped silicon. The heavily doped silicon behaves like a metal with lower carrier concentration and has a smaller electron–phonon thermal coupling. We have fabricated superconductor-doped silicon-superconductor contacts (S-Sm-S) and we have used them as thermometers and coolers.     

Graft copolymerization of different mixtures of acrylic monomers on amylopectin. Swelling behavior

Hydroxylic and nonhydroxylic acrylates—methyl acrylate (MA), ethyl acrylate (EA), butylacrylate (BA), hydroxypropyl methacrylate (HPMA), ethylenglycol dimethacrylate (EGDMA), and mixtures of HPMA–MA, HPMA–EA, HPMA–BA in a 50/50 feed composition—were grafted onto amylopectin with different amounts of crosslinking agent, EGDMA. Percent of total conversion, percent crude grafting, and influence of pH in water content were studied. In this sense it was only at pH 10 when a real variation in the water content could be seen. It was also proved that the highest values were obtained when one of the comonomers was EGDMA with a 34 mol% of the initial feed composition. © 1994 John Wiley & Sons, Inc.     

Transmission Electron Microscopy and Electron Energy-Loss Spectroscopy Characterization of Glass Phase in Sol-Gel-Derived Mullite

Sol-gel-derived mullite ceramics were processed by pressureless sintering at 1600°, 1650°, and 1700°C for 4 h. Microstructural and microchemical characterization of the mullite materials was performed using transmission electron microscopy, in conjunction with energy-dispersive X-ray spectroscopy and electron energy-loss spectroscopy (EELS). Apart from mullite grain diameter and triplepocket size, no major microstructural changes were observed with increasing sintering temperature. Residual glass was present at triple pockets and along two-grain junctions. Not all grain boundaries revealed the presence of a continuous amorphous intergranular film. Clean interfaces were observed only at boundaries with one grain parallel to the [001] orientation (low-energy configuration). Quantitative EELS analysis of mullite grains and glass pockets revealed only small changes in composition with increasing sintering temperature; i.e., the alumina:silica ratio slightly increased for mullite and glass. The analysis implied that mullite with this relatively high aluminum content would not be stable adjacent to residual glass. However, a stable glass-mullite system has been proposed, because impurity cations were detected within glass pockets, which suggested a slight shift of the subsolidus line (glass-mullite/ mullite) to a higher amount of alumina. Energy-loss nearedge structure studies of the Si- L _2,3 edge revealed a similar near-edge structure for the mullite, residual glass, and quartz. Thus, SiO₄ tetrahedra were thought to be the main building units of the glass contained in sintered mullite.     

Relations between cardiac and vascular structure in patients with primary and secondary hypertension

BACKGROUND: Data on cardiac and vascular structure in secondary hypertension are generally scarce, and no data on the interrelations between cardiac mass and structural characteristics of the vessel wall, both in large and in small resistance arteries, are presently available. OBJECTIVES: The aim of this study was to investigate the relation between structural changes in subcutaneous small arteries, left ventricular mass and wall thickness of the common carotid artery in patients with primary and secondary hypertension. METHODS: Seventy-four subjects were included in the study: 11 patients with pheochromocytoma, 14 with primary aldosteronism (PA), 19 with renovascular hypertension (RVH), 18 with essential hypertension (EH) and 12 normotensive (NT) control subjects. All subjects were submitted to a biopsy of subcutaneous fat. Morphologic characteristics of subcutaneous small resistance arteries (relaxed diameter <300 microm) were directly evaluated using a micromyographic technique. All subjects were submitted to calculation of left ventricular mass index (LVMI) and common carotid artery intima-media thickness (CCIMT), using ultrasound technique. RESULTS: The correlation coefficients between the media to lumen ratio in subcutaneous small arteries (M/L) and LVMI or between M/L and CCIMT were closer in RVH than in pheochromocytoma, EH or NT; in PA the correlation coefficients were slightly less close than those in RVH. An excess prevalence of carotid plaques in RVH was observed. CONCLUSIONS: A close relation between small resistance artery morphology and cardiac or carotid artery structure may be observed in those hypertensive patients in whom the renin-angiotensin-aldosterone system is activated. In constrast, in NT, EH and pheochromocytoma no significant correlation between M/L and LVMI or CCIMT was observed.