Evaluation of Laminated Circular Elastomeric Bearings

This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance.     

The effect of hydrogen in the mechanism of aluminum-induced crystallization of sputtered amorphous silicon using scanning Auger microanalysis

The metal-induced crystallization (MIC) of hydrogenated sputtered amorphous silicon (a-Si:H) using aluminum has been investigated using X-ray diffraction (XRD) and scanning Auger microanalysis (SAM). Hydrogenated, as well as non-hydrogenated, amorphous silicon (a-Si) films were sputtered on glass substrates, then capped with a thin layer of Al. Following the depositions, the samples were annealed in the temperature range 200 °C to 400 °C for varying periods of time. Crystallization of the samples was confirmed by XRD. Non-hydrogenated films started to crystallize at 350 °C. On the other hand, crystallization of the samples with the highest hydrogen (H₂) content initiated at 225 °C. Thus, the crystallization temperature is affected by the H₂ content of the a-Si. Material structure following annealing was confirmed by SAM. In this paper, a comprehensive model for MIC of a-Si is developed based on these experimental results.     

Fabrication and Characterization of Undoped and Cobalt-doped ZnO Based UV Photodetector Prepared by RF-sputtering

Undoped and 1 at.% Co-doped ZnO nanostructure based UV photodetectors were successfully fabricated by RF- magnetron sputtering technique with comb like Pt electrodes. Cobalt ions were successfully incorporated into the lattice of the ZnO nanostructure without changing its wurtzite structure. It was indicated that Co-doping can effectively adjust the luminescence properties of the ZnO nanostructure. The undoped and Co-doped ZnO photodetectors were observed to have photosensitivities of 1.44 x 104 % and 8.57 x 102 % and low dark currents of 9.74 x 10-8 A and 1.18 x 10-7 A, respectively.     

Resistance of exterior three-dimensional walls to high velocity projectiles

There have been a number of recent civilian deaths due to ammunition from commonly used firearms penetrating exterior walls of residential, public, and commercial buildings. Experimental research was conducted to study the behavior of three-dimensional (3D) exterior walls when subjected to high velocity projectiles or bullets fired from a variety of firearms of different calibers. Four types of firearms were used, namely, a 9 mm gun, a 0.357 Magnum gun, an M16 machine gun, and a 7.62 Clashin Koff machine gun. The size of chips and the depth of penetrations produced by the fired bullets are documented and discussed. It was found that none of the fired bullets penetrated the two reinforced concrete layers of the exterior wall. In conclusion, 3D exterior walls provide an acceptable level of protection from ammunition fired from commonly used firearms.     

The propagation of pressure in a gelled waxy oil pipeline as studied by particle imaging velocimetry

Paraffinic crude oils in pipelines may form waxy gels during flow shutdowns. These gels can be dislodged by applying pressure if the wall shear stress, proportional to the local pressure gradient, exceeds the gel yield stress. The simplest models assume that the axial pressure profile becomes linear immediately after a jump in upstream pressure, but this fails to account for gel time‐dependent rheology or the effect of gel voids on pressure wave propagation. To investigate the former factor, pressure profile and particle imaging velocimetry (PIV) measurements were performed on a model oil gelled under pressure to reduce void formation. After a jump in upstream pressure to a value insufficient to restart flow, the axial pressure profile becomes linear in a two‐step process, with an immediate small rise in downstream pressure followed by a time‐delayed jump. The local downstream gel deformation measured by PIV exhibits similar two‐step time dependence. © 2011 American Institute of Chemical Engineers AIChE J, 2012     

Occurrence of phthalate metabolites in human urine from several Asian countries

The occurrence of 14 phthalate metabolites was found in human urine samples collected from seven Asian countries: China, India, Japan, Korea, Kuwait, Malaysia, and Vietnam. Phthalate metabolites were found in all samples, indicating widespread exposure of humans to phthalates in these Asian countries. The highest total (the sum of 14 phthalates) phthalate metabolite concentrations were found in samples collected from Kuwait (median: 1050 ng/mL), followed in decreasing order by samples from India (389 ng/mL), China (234 ng/mL), Vietnam (133 ng/mL), Japan (120 ng/mL), Korea (117 ng/mL), and Malaysia (94.9 ng/mL). The creatinine-adjusted median concentrations of total phthalates for urine samples from Kuwait, India, China, Vietnam, Japan, Korea, and Malaysia were 692, 506, 289, 119, 103, 104, and 169 μg/g creatinine, respectively. Monomethyl phthalate (mMP), monoethyl phthalate (mEP), mono (2-isobutyl phthalate) (miBP), mono-n-butyl phthalate (mBP), and metabolites of di-(2-ethylhexyl) phthalate (DEHP) were the dominant compounds, collectively accounting for >95% of the total concentrations in the samples from the seven countries. The profiles of urinary phthalate metabolite concentrations varied among the samples collected from the seven countries. Urine samples from Kuwait contained the highest concentrations of mEP (median: 391 ng/mL), mBP (94.1 ng/mL), and the metabolites of DEHP (202 ng/mL), whereas samples from China and Japan contained the highest concentrations of miBP (50.8 ng/mL) and mMP (17.5 ng/mL), respectively. mEP was the predominant metabolite in urine samples from India and Kuwait (accounting for 49% of the total), mBP and miBP were the predominant compounds in samples from China (52%), and DEHP metabolites were the predominant compounds in samples from Korea (46%) and Vietnam (52%). Based on the urinary concentrations of mEP, mBP, miBP, and DEHP metabolites of the samples from the seven Asian countries, we estimated daily intake rates of diethyl phthalate (DEP), dibutyl phthalate (DBP), and DEHP. The results indicated that people in the seven Asian countries are exposed to DEP, DBP, and DEHP at levels well below the reference doses (RfD) suggested as unsafe by the U.S. Environmental Protection Agency (EPA). The estimated exposure doses to DEHP in Kuwait, however, were above the RfD recommended by the EPA.     

A parametric study on the factors affecting the froth floatation of Jordanian tar sand utilizing a fluidized bed floatator

Different parameters affecting the behavior of froth flotation of Jordanian tar sand, obtained from the Dead Sea area, were studied. This study was performed in a modified fluidized bed floatator. The effects of the addition of a flotation agent, NaOH, temperature and flotation time on the beneficiation of bitumen in the froth were investigated. It was found that the beneficiation factor in the froth increased with the increase of temperature and flotation time. However, the amount of base (NaOH) and the flotation agent were found to have a negative effect on that factor. A regression model based on a full factorial experimental design results was obtained with a significant correlation coefficient. The optimum beneficiation factor was found to be 7.2 and the bitumen content in the froth was found to be 79% in the froth, which was obtained at 0.2 gNaOH/L, zero agent, 80 °C, and 30 min.     

Investigation of multiconversion processes in periodically poled LiNbO3-based optical parametric oscillators

The multiconversion processes in optical parametric oscillators based on periodically poled LiNbO3 are investigated. Interpretations based on simultaneous quasi- and birefringent phase matching are presented. Three parametric and three harmonic generation processes in a multigrating periodically poled LiNbO3 crystal were observed. Two of the parametric processes and two of the harmonics were quasi-phase matched, and the other conversion processes were phase matched through birefringence in the crystal. The primary parametric process (omegap --> omegas + omegai) was obtained through first-order quasi-phase matching. The other quasi-phase-matched processes occurred within higher orders. The existence of even-order quasi-phase matching in the crystal is due to other than a 50% duty-cycle grating periods. The tuning range for each of the generated waves is obtained and compared with theoretical fittings.     

Thermoset IM-LSI-based C/C-SiC: Influence of flow direction and weld lines on microstructure and mechanical properties

The production of ceramic matrix composites (CMC) based on C/C-SiC is still very cost-intensive and therefore only economical for a few applications. The fabrication of the preforms involves many costs that need to be reduced. In this work, the shaping of the CFRP-preforms is realized by thermoset injection molding, which enables large-scale production. The polymeric matrix used is a multi-component matrix consisting of novolak resin, curing agent and lubricant. Six millimeter chopped carbon fiber with a proportion of 50 wt.% were used as a reinforcement. These ingredients are processed by an industrial equipment for compounding and injection molding in order to manufacture a CFRP demonstrator representing a brake disc. Test specimens are cut out of the demonstrator in different directions in order to investigate influences of flow direction and weld lines on microstructural and mechanical properties. Afterward, the CFRP samples were converted to C/C-SiC composites by the liquid silicon infiltration process. The article addresses the flow behavior of the compound during the injection molding and the building of the weld lines in the demonstrator. In addition, results of the directional dependence of the microstructural and mechanical properties within the fabricated disc in the different production steps are presented.