Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

A family of converters for UPS production burn-in energy recovery

This paper introduces a family of power converters for power recycling during the burn-in test of synchronized uninterruptible power supplies (UPSs) with sinusoidal output voltage. The use of the power recycler to replace the resistor load bank in the UPSs burn-in test causes great energy savings, and the optimized use of electrical energy contributes in reducing the final cost of the product. The main feature of the new circuits is their ability to draw from the UPS and to inject into the utility-grid currents with low total harmonic distortion (THD) and high power factor (PF). The new circuits operate at constant frequency and are regulated by conventional pulse width modulation (PWM) using dedicated PWM and PF controller integrated circuits developed for power supplies. Circuit operation, mathematical analysis, design example, and experimental results for discontinuous current mode (DCM) and continuous current mode (CCM) operation are provided in this paper     

Isolated DC-DC converters with high-output voltage for TWTA telecommunication satellite applications

Two alternatives for the implementation of an isolated DC-DC converter operating with a high output voltage and supplied by an unregulated low input voltage are presented in this paper. The proposed topologies are especially qualified for the implementation of travelling wave tube amplifiers (TWTA) utilized in telecommunication satellite applications due to their low mass and volume and their high-efficiency. The converters studied follow different principles and the main operational aspects of each topology are analyzed. A two-stage structure composed by a regulator connected in series with a ZVS/ZCS isolated DC-DC converter is the first topology proposed. The second topology studied is an isolated single-stage converter that continues being highly efficient even with a large input voltage variation. The experimental results obtained from two prototypes, implemented following the design procedures developed, are presented, verifying experimentally the characteristics and the analysis of the proposed structures. The prototypes are developed for an application requiring an output power of 150 W, a total output voltage of 3.2 kV and an input voltage varying from 26 V to 44 V. The minimum efficiency obtained for both converters operating at the nominal output power, is equal to 93.4% for the two-stage structure and equal to 94.1% for the single-stage converter.     

A survey of nitrate and nitrite content of fruit and vegetables grown in Slovenia during 1996-2002

Monitoring of nitrate (NO₃^-) and nitrite (NO₂^-) content in agricultural products in Slovenia has been carried out since 1996. The results of monitoring over the period 1996-2002 are presented. During this time 924 samples of 14 different agricultural products (potato, lettuce, apples, carrot, silage maize, cabbage, grapes, peaches, string beans, cereals, pears, cucumbers, strawberries and tomato) were analysed. The samples were taken at the time of maturity directly from growing sites and they were analysed using segmented flow analysis. The average nitrate contents were the highest in lettuce (1074 mg kg^-1), cabbage (881 mg kg^-1), string beans (298 mg kg^-1) and carrot (264 mg kg^-1), and they were moderately high in potato (158 mg kg^-1), silage maize (122 mg kg^-1), strawberries (94 mg kg^-1), cucumbers (93 mg kg^-1) and cereals (49 mg kg^-1). Low nitrate contents (below 6 mg kg^-1) were found in fruit (grapes, peaches, apples and pears) and tomato. With the exception of cereals (8.9 mg kg^-1), apples (1.5 mg kg^-1), potato (1.2 mg kg^-1) and pears (1.0 mg kg^-1) the content of nitrites did not exceed 0.5 mg kg^-1. It may be concluded that the results of the monitoring were in most cases similar to the results of investigations obtained in other countries.     

A new ZVS-PWM unity power factor rectifier with reduced conductionlosses

This paper introduces a new single-phase high power factor rectifier, which features regulation by conventional PWM, soft commutation and instantaneous average line current control. Furthermore, thanks to the use of a single converter, instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter, a significant reduction in the conduction losses is achieved. A prototype rated at 1.6 kW, operating at 70 kHz, with an input AC voltage of 220 Vrms and an output voltage of 400 V_DC has been implemented in the laboratory. An efficiency of 97.8 % at 1.6 kW has been measured. Analysis, design, and the control circuitry are also presented in the paper     

A large-displacement 65Pb(Mg1/3Nb2/3)O3–35PbTiO3/Pt bimorph actuator prepared by screen printing

In this paper we present a novel approach to preparing large-displacement 65Pb(Mg_1/3Nb_2/3)O₃–35PbTiO₃/Pt (65/35 PMN–PT/Pt) bimorph actuators. These “substrate-free”, bending-type actuators were prepared by screen-printing the 65/35 PMN–PT and Pt thick-film pastes as the electrodes on alumina substrates. After this screen printing and the subsequent firing the 65/35 PMN–PT/Pt composites were peeled off from the substrates. Displacements of nearly 100 μm at 18 V were achieved for actuators with dimensions of 1.8 cm × 2.5 mm × 50 μm for the 65/35 PMN–PT layer. The normalized displacement (the displacement per unit length) was 40 μm/cm at 18 V. The experimental results together with a computation procedure were used to obtain the material parameters for a finite-element analysis of the 65/35 PMN–PT/Pt bimorph actuators.     

A network of pyramidal neurons is sensitive to the timing of its excitatory inputs

The transmission of excitatory inputs by a network of coupled pyramidal cells is investigated by means of numerical simulations. The pyramidal cell models are coupled by excitatory synapses and each one receives an excitatory pulse at a random time extracted from a Gaussian distribution. Moreover, each cell model is injected with a noisy current. It was found that the excitatory coupling promotes the transmission of the synaptic inputs on a time scale of a few ms.     

Influence of Particle Size Distribution,Moisture Content,and Particle Shape on the Flow Properties of Bulk Solids

Abstract

There has been a great deal of research on characterising bulk solids. However, some of the characteristics, particularly the time‐dependent and random changes of properties, still remain insufficiently understood. The focus of this article is to study the influence of particle size, size distribution, moisture content, and particle shape on the unconfined yield strength of bulk solids. We present some interesting results about the influence of the particle size distribution on the unconfined yield strength of a bulk solid and a new method for determining the influence of particle shape on the unconfined yield strength of a bulk solid, which was made possible by the design and use of a novel attritor.     

Permutation routing in double-loop networks: design and empirical evaluation

A double-loop network is an undirected graph whose nodes are integers 0,1,…,n−1 and each node u is adjacent to four nodes u±h₁(mod>n), u±h₂(mod>n), where 0<h₁<h₂<n/2. There are initially n packets, one at each of the n nodes. The packet at node u is destined to node π(u), where the mapping uπ(u) is a permutation. The aim is to minimize the number of routing steps to route all the packets to their destinations. If ℓ is the tight lower bound for this number, then the best known permutation routing algorithm takes, on average, 1.98ℓ routing steps (and 2ℓ routing steps in the worst-case).Because the worst-case complexity cannot be improved, we design four new static permutation routing algorithms with gradually improved average-case performances, which are 1.37ℓ, 1.35ℓ, 1.18ℓ, and 1.12ℓ. Thus, the best of these algorithms exceeds the optimal routing by at most 12% on average.To support our algorithm design we develop a program which simulates permutation routing in a network according to the given topology, routing model as well as communication pattern and measure several quality criteria. We have tested our algorithms on a large number of double-loop networks and permutations (randomly generated and standard).