Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Binding of heavy metal ions by formaldehyde-polymerized peanut skins

Peanut skin, when treated with formaldehyde to polymerize tannins, is a highly efficient substrate for removal of many heavy metal ions from aqueous waste solutions. The ions Ag¹⁺, Cd²⁺, Cr⁶⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, as well as Ca²⁺ and Mg²⁺, were contacted with formaldehyde-treated peanut skin. Quantitative removal could be achieved with Ag¹⁺, Cd²⁺, Cu²⁺, Hg²⁺, Pb²⁺, and Zn²⁺. Capacity of the substrate for ions was promising for Pb²⁺ (2.1 meq/g substrate), Cu²⁺ (3.0 meq/g), and Cd²⁺ (1.3 meq/g). Sorption from a solution containing Cd²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Pb²⁺, Zn²⁺, on a packed column of formaldehyde-treated peanut skin indicated that Hg²⁺, Pb²⁺, and Cu²⁺ were rapidly and completely bound to the packing, while Cd²⁺, Ni²⁺, and Zn²⁺ were poorly bound until the preferred ions had been removed from solution.     

BOAR: an advanced HW/SW coemulation environment for DSP system development

The BOAR emulation system is targeted to hardware/software (HW/SW) codevelopment of advanced embedded DSP and telecom systems. The challenge of the BOAR system is efficient customization of programmable hardware, and dedicated partitioning routine to target applications and structures, which allows quite high overall system performance. The system allows multiple configurations for communication between processors and field programmable gate arrays (FPGAs) making the BOAR system an efficient tool for real-time HW/SW coverification. The reprogrammable hardware of the emulation tool is based on four Xilinx 4000-series devices, two Texas TMS320C50 signal processors and one Motorola MC68302 microcontroller. With current devices the BOAR hardware provides approximately 40–70 kgates of logic capacity in DSP applications. The emulation capacity can be expanded by connecting several similar boards in chain. The system has also a versatile internal reprogrammable test environment for test bench development, performance evaluations and design debugging. The logic development environment is based on the Synopsys synthesis tools and an automatic design management software, which performs resource mapping and performance-driven design partitioning between FPGAs. The emulation hardware is currently connected to logic and software development environments via an RS-232C bus. The BOAR emulation system has been found a very efficient platform for real-life prototyping of different types of DSP algorithms and systems, and validating correct functionality of a VHDL macro library.     

Insights into corrosion in dye solar cells

The main issue in using low cost metals in dye solar cells is the corrosion caused by the liquid electrolyte. Contrary to typical applications of metals, the adverse effects of corrosion in dye solar cells are related to irreversible depletion of charge carriers from the electrolyte rather than consumption of the metal itself. It is calculated that the penetration rate due to corrosion should not exceed 10⁻⁴ mpy (a couple of nanometers per year) to ensure device lifetime longer than 1 year. This is 10 000 times slower rate than what is considered to be a general benchmark value for very low corrosion rate in the field of corrosion science and has a major effect on how corrosion should be investigated in the case of dye solar cells. Different methods, their applicability, and limitations to investigate corrosion in dye solar cells are evaluated here. The issue with most techniques is that they can detect metals that are clearly corroding, but they have significant limitations in proving a metal stable. Our investigation shows that the most reliable information on corrosion is obtained from complete dye solar cells that are exposed to working conditions. A combination of color analysis of the electrolyte to such measurement is proposed as a means to extrapolate future performance of the cells and estimate potential lifetimes of the dye solar cells in regards to corrosion. Copyright © 2014 John Wiley & Sons, Ltd.     

The use of functionalized polymers as photosensitizers in an energy storage reaction

Insoluble polymer bound photosensitizers, useful for the conversion of norbornadiene (1) to quadricyclene (2), have been synthesized. An acetophenone analogue was produced by Friedel-Crafts acylation of polystyrene resin while treatment of chloromethylated resin with salicyladehyde and triethylamine produced an anlogue of benzyloxybenzaldehyde. Reaction of lithio---polystyrene resin with methyl 4-(N,N-dimethylamino)benzoate gave a ketone equivalent to 4-(N,N-dimethylamino)benzophenone (3). Quantum yields for the conversion of 1 and 2 using the polymer bound sensitizers were generally comparable to, but slightly lower than, the analogous compound in homogeneous solution. The quantum yield of polymer bound 3 was less solvent dependent than that of the homogeneous counterpart. The advantages of isolating the photosensitizer to the photochemical reactor stage of a photochemical solar energy storage device are discussed. Efficient sensitization by polymer bound photosensitizers demonstrates the feasibility of this approach.     

Fluorescence quenching-based assays for hydrolyzing enzymes. Application of time-resolved fluorometry in assays for caspase, helicase, and phosphatase

We have developed assay technologies to measure hydrolyzing enzymes based on homogeneous time-resolved fluorescence quenching (TruPoint). High sensitivity was obtained using fluorescent europium chelates as labels, internally quenched by suitable quenchers and released upon enzymatic reaction. This approach allows robust and sensitive monitoring of low enzyme activities. The assay technology and the choice of donor-acceptor pairs were evaluated in three different enzymatic assays, a protease related to apoptosis, helicase involved in DNA unwinding, and phosphatase having an important role in cellular signaling cascades. All the assays produced an increasing signal, were sensitive, and had a good dynamic range. There were significant differences in optimized quenchers for each of the assays depending on the size, flexibility, and rigidity of the substrates. Also, clear differences in the energy-transfer reactions, their requirements for spectral overlapping, ionic interactions, and energy-transfer distances were found. Each of the enzymatic assays was briefly tested in a high-throughput screening environment by analyzing signal dynamics and statistical relevance as Z' factors.     

Tissue reactions of subcutaneously implanted mixture of ε-caprolactone-lactide copolymer and tricalcium phosphate. An electron microscopic evaluation in sheep

Biodegradable polymers, mainly derivates of -hydroxy acids, are widely used today in oral- and maxillofacial surgery, orthopedics, and other fields of surgery. These biomaterials are well tolerated by living tissue and fracture fixation devices made of polylactic or polyglycolic acid are clinically widely used today. Still, there are some problems in application of biodegradable polymers. Abacterial inflammatory reactions have been noticed after the clinical introduction of these devices. Both swelling and pain at the site of implantation have also been reported. The etiology of this inflammatory reaction is still unknown, despite the numerous studies. Therefore, the aim of the present study was to further characterize this inflammatory reaction in detail, by electronmicroscopy. We prepared a mixture of -caprolactone–lactide copolymer and tricalcium phosphate and placed it in the dermis in 12 sheep. Follow-up times were 9, 14, 24, and 52 weeks. We found that the mixture caused a mild inflammatory reaction. There were no signs of cell damage. Fibroblasts, macrophages, and eosinophils were found adjacent to the copolymer. The mixture is easy to handle and can be moulded into different shapes in room temperature. The results encourage us to continue our studies to develop a filling material for bone defects.