Energetics of Plastic Deformation of Metastable Austenitic Stainless Steel

The change in the internal energy during uniaxial tensile deformation of austenitic stainless steels EN 1.4301 (AISI 304) and EN 1.4318 (AISI 301LN) was determined by measuring the extent of γ→α'‐martensite transformation and the temperature increase of the samples. From the results the fraction of the stored energy of cold work and the free energy change related to the strain‐induced γ→α'‐martensite transformation were determined. The fraction of stored energy varied around 0.4. With the metastable steel grades the free energy change related to the γ→α'‐martensite transformation was found to vary between ‐98 MJ/m³ and ‐206 MJ/m³ depending on the austenite stability of the steel. Furthermore, the magnitude of the mechanical driving force was estimated by comparing the results with the free energy change of thermally induced transformation.     

Correcting for the influence of frozen lakes in satellite microwave radiometer observations through application of a microwave emission model

The spatial resolution of passive microwave observations from space is of the order of tens of kilometers with currently available instruments, such as the Special Sensor Microwave/Imager (SSM/I) and Advanced Microwave Scanning Radiometer (AMSR-E). The large field of view of these instruments dictates that the observed brightness temperature can originate from heterogeneous land cover, with different vegetation and surface properties.In this study, we assess the influence of freshwater lakes on the observed brightness temperature of AMSR-E in winter conditions. The study focuses on the geographic region of Finland, where lakes account for 10% of the total terrestrial area. We present a method to mitigate for the influence of lakes through forward modeling of snow covered lakes, as a part of a microwave emission simulation scheme of space-borne observations. We apply a forward model to predict brightness temperatures of snow covered sceneries over several winter seasons, using available data on snow cover, vegetation and lake ice cover to set the forward model input parameters. Comparison of model estimates with space-borne observations shows that the modeling accuracy improves in the majority of examined cases when lakes are accounted for, with respect to the case where lakes are not included in the simulation. Moreover, we present a method for applying the correction to the retrieval of Snow Water Equivalent (SWE) in lake-rich areas, using a numerical inversion method of the forward model. In a comparison to available independent validation data on SWE, also the retrieval accuracy is seen to improve when applying the influence of snow covered lakes in the emission model.     

Effect of strain rate on the strain-induced <Emphasis Type="Italic">γ</Emphasis> → <Emphasis Type="Italic">α</Emphasis>′-martensite transformation and mechanical properties of austenitic stainless steels

The effect of strain rate on strain-induced γ → α′-martensite transformation and mechanical behavior of austenitic stainless steel grades EN 1.4318 (AISI 301LN) and EN 1.4301 (AISI 304) was studied at strain rates ranging between 3×10⁻⁴ and 200 s⁻¹. The most important effect of the strain rate was found to be the adiabatic heating that suppresses the strain-induced γ → α′ transformation. A correlation between the work-hardening rate and the rate of γ → α′ transformation was found. Therefore, the changes in the extent of the α′-martensite formation strongly affected the work-hardening rate and the ultimate tensile strength of the materials. Changes in the martensite formation and work-hardening rate affected also the ductility of the studied steels. Furthermore, it was shown that the square root of the α′-martensite fraction is a linear function of flow stress. This indicates that the formation of α′-martensite affects the stress by influencing the dislocation density of the austenite phase. Olson-Cohen analysis of the martensite measurement results did not indicate any effect of strain rate on shear band formation, which was contrary to the transmission electron microscopy (TEM) examinations. The β parameter decreased with increasing strain rate, which indicates a decrease in the chemical driving force of the α → α′ transformation.     

Brewing of glucuronic acid-enriched apple cider with enhanced antioxidant activities through the co-fermentation of yeast (Saccharomyces cerevisiae and Pichia kudriavzevii) and bacteria (Lactobacillus plantarum)

Co-fermentation using yeast (Saccharomyces cerevisiae and Pichia kudriavzevii) and the bacteria (Lactobacillus plantarum) as starters isolated from spontaneous sourdough was conducted for the brewing of glucuronic acid (GlcA)-enriched apple cider. The concentration of GlcA in the apple cider co-fermented for 14 d with commercial S. cerevisiae and L. plantarum was 37.7 ± 1.7 mg/mL while a concentration of 62.8 ± 3.1 mg/mL was recorded for fermentation with P. kudriavzevii and L. plantarum, which was higher than the corresponding single yeast fermentation. The co-fermented apple cider revealed higher 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity of 171.67 ± 0.79 µg trolox equivalents (TE)/mL using P. kudriavzevii and L. plantarum, compared to the control (143.89 ± 7.07 µg TE/mL) just using S. cerevisiae. Thus, the co-fermentation of S. cerevisiae and L. plantarum and P. kudriavzevii and L. plantarum provided a new strategy for the development of GlcA-enriched apple cider with enhanced antioxidant capacity.     

Geckoprinting: assembly of microelectronic devices on unconventional surfaces by transfer printing with isolated gecko setal arrays

Developing electronics in unconventional forms provides opportunities to expand the use of electronics in diverse applications including bio-integrated or implanted electronics. One of the key challenges lies in integrating semiconductor microdevices onto unconventional substrates without glue, high pressure or temperature that may cause damage to microdevices, substrates or interfaces. This paper describes a solution based on natural gecko setal arrays that switch adhesion mechanically on and off, enabling pick and place manipulation of thin microscale semiconductor materials onto diverse surfaces including plants and insects whose surfaces are usually rough and irregular. A demonstration of functional ‘geckoprinted’ microelectronic devices provides a proof of concept of our results in practical applications.     

The Effects of KCl,NaCl and K<Subscript>2</Subscript>CO<Subscript>3</Subscript> on the High-Temperature Oxidation Onset of Sanicro 28 Steel

The present study investigates the early stages in the oxidation process of Sanicro 28 (Fe31Cr27Ni) stainless steel when exposed to an alkali salt (KCl, NaCl or K₂CO₃) for 2 h at 450 and 535 °C. After the exposure, the oxidized samples were analyzed with a combinatory method (CA, XPS and SEM–EDX). It was found that all three salts were corrosive, and the overall oxidation reaction rate was much higher at 535 °C than at 450 °C. There were clear differences in terms of the impact of cations (Na⁺, K⁺) and anions (Cl^?, CO₃ ^2?) on the initial corrosion process at both temperatures. When focusing on the cations, the presence of potassium ions resulted in a higher rate of chromate formation than in the presence of sodium ions. When studying the effect of anions, the oxidation of iron and chromium occurred at higher rates in the presence of both chloride salts than in the presence of the carbonate salt, and chloride salts seemed to possess higher diffusion rate in the gas phase and along the surface than carbonate salts. Moreover, at the higher temperature of 535 °C, the formed chromate reacted further to chromium oxide, and an ongoing oxidation process of iron and chromium was identified with a significantly higher reaction rate than at 450 °C.     

Studies on Helium Liquids by Vibrating Wires and Quartz Tuning Forks

We present results of low-temperature experiments on dilute mixtures of ³He in ⁴He and on pure ³He, obtained by means of two kinds of mechanical oscillators immersed in the liquid sample: vibrating wires and quartz tuning forks. The helium sample was cooled either by adiabatic demagnetization of an immersed copper nuclear stage or by adiabatic melting of ⁴He in superfluid ³He. The measured effect of the surrounding fluid on the mechanical resonance of the oscillators is compared with existing theories. We also discuss resonances of second sound and the state of supersaturation, both observed by a tuning fork in helium mixtures.     

Carbocations as Lewis Acid Catalysts: Reactivity and Scope

One class of potential Lewis acids that has received negligible attention as a catalyst is the carbocation. Here we show the potential of triarylmethylium ions as highly powerful Lewis acid catalysts for organic reactions. The Lewis acidity of the triarylmethylium ion can be easily tuned by variation of the electronic properties of the aromatic rings and the catalytic activity of the carbocation is shown to correlate directly to the level of stabilization of the empty p_C‐orbital at the cationic carbon. The versatility of triarylmethylium ions as efficient Lewis acid catalysts for organic reactions is demonstrated in Diels–Alder, aza‐Diels–Alder, conjugate addition, halogenation, epoxide rearrangement and intramolecular hetro‐ene reactions.