A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

Measurements of coupling and reflection characteristics of butt-joints in passive waveguide integrated laser diodes

Amplified spontaneous emission (ASE) spectra of passive waveguide integrated lasers have been studied to estimate the coupling efficiency and the reflectivity at the butt-joints between active and passive waveguides. A new method has been proposed for the analysis of ASE to extract the coupling efficiency and reflectivity at the butt-joints. This method was applied experimentally to estimate the coupling and reflection of the passive waveguide integrated lasers with different amounts of vertical misalignments of active and passive waveguides.     

Performance of GaAs-AlGaAs V-grooved inner stripe quantum-well wirelasers with different current blocking configurations

GaAs-AlGaAs V-grooved inner stripe (VIS) quantum-well wire (QWW) lasers grown by metalorganic chemical vapor deposition with different current blocking configurations, n-blocking on p-substrate (VIPS), p-n-p-n blocking on n-substrate (VI(PN)_nS) and p-blocking on n-substrate (VINS) have been fabricated and characterized. The VIPS QWW lasers show the most stable characteristics with effective current confinement: one of the lasers shows fundamental transverse mode, lasing up to 5 mW/facet, typical threshold current of 39.9 mA at 818.5 mm, an external differential quantum efficiency of 24%/facet, and characteristic temperature of 92 K. The current tuning rate was almost linear at 0.031 mm/mA, and the temperature tuning rate was measured to be 0.14 nm/°C. Comparison of the light output versus current characteristics of the lasers with different current blocking configurations is presented here     

Parasitic Bipolar Junction Transistors in a Floating-Gate MOSFET for Fluorescence Detection

In this letter, we examined whether the parasitic bipolar junction transistors (BJTs) in the MOSFET fabricated by the standard CMOS process can play a role as a fluorescence detector. To suppress the action of two vertical parasitic BJTs, the gate and n-well were tied in the parasitic BJTs, and the body node was connected to the drain. The proposed device was compared with the inherent and the parasitic diodes in the MOSFET. It had 100 times higher photocurrents than the diodes in the MOSFET. In addition, it was applied for the detection of the fluorescent signal, and could detect near 10 nM of Alexa 546. Therefore, CMOS-process-compatible parasitic BJTs can be used as a photodetector in an integrated fluorescence detector.     

k-Nearest neighbor query processing algorithm for cloaking regions towards user privacy protection in location-based services

Due to the advancement of wireless internet and mobile positioning technology, the application of location-based services (LBSs) has become popular for mobile users. Since users have to send their exact locations to obtain the service, it may lead to several privacy threats. To solve this problem, a cloaking method has been proposed to blur users’ exact locations into a cloaked spatial region with a required privacy threshold (k). With the cloaked region, an LBS server can carry out a k-nearest neighbor (k-NN) search algorithm. Some recent studies have proposed methods to search k-nearest POIs while protecting a user’s privacy. However, they have at least one major problem, such as inefficiency on query processing or low precision of retrieved result. To resolve these problems, in this paper, we propose a novel k-NN query processing algorithm for a cloaking region to satisfy both requirements of fast query processing time and high precision of the retrieved result. To achieve fast query processing time, we propose a new pruning technique based on a 2D-coodinate scheme. In addition, we make use of a Voronoi diagram for retrieving the nearest POIs efficiently. To satisfy the requirement of high precision of the retrieved result, we guarantee that our k-NN query processing algorithm always contains the exact set of k nearest neighbors. Our performance analysis shows that our algorithm achieves better performance in terms of query processing time and the number of candidate POIs compared with other algorithms.     

Effect of Nitrogen Atmosphere on the Densification of a 3-mol%-Yttria-Doped Zirconia

The densification behavior of a 3-mol%-Y₂O₃-doped ZrO₂ (3Y-ZrO₂) has been investigated under N₂ and O₂ atmospheres. Powder compacts have been sintered at 1550° and 1400°C for various times. The density of the specimen sintered at 1550°C is higher in N₂ than in O₂, while the contrary result is obtained in the case of the specimen sintered at 1400°C. Such results can be explained in terms of nitrogen solubility and oxygen vacancy in a ZrO₂ matrix. Because nitrogen solubility into the ZrO₂ increases with an increase in heat-treatment temperature, leading to the formation of oxygen vacancy, the densification rate becomes higher. The present study thus shows evidence of nitrogen solubility into the ZrO₂ and its role on the densification behavior of 3Y-ZrO₂.     

Note: High speed optical profiler based on a phase-shifting technique using frequency-scanning lasers

We present a high speed optical profiler (HSOP) using frequency-scanning lasers for three-dimensional profile measurements of microscopic structures. To improve upon previous techniques for implementing the HSOP, we developed frequency-scanning lasers and a compact microscopic interferometer. The controller of the HSOP was also modified to generate proper phase-shifting steps. For measurements of step height specimens, the HSOP showed results comparable with a commercial optical profiler, even with much higher measurement speeds (up to 30 Hz). The typical repeatability of step height measurement was less than 1 nm. We also present measurements of microscopic structures to verify the HSOP's ability to perform high speed inline inspection for the semiconductor and flat-panel display industries.     

Color laser printer forensic based on noisy feature and support vector machine classifier

Digital forensics in the ubiquitous era can enhance and protect the reliability of multimedia content where this content is accessed, manipulated, and distributed using high quality computer devices. Color laser printer forensics is a kind of digital forensics which identifies the printing source of color printed materials such as fine arts, money, and document and helps to catch a criminal. This paper present a new color laser printer forensic algorithm based on noisy texture analysis and support vector machine classifier that can detect which color laser printer was used to print the unknown images. Since each printer vender uses their own printing process, printed documents from different venders have a little invisible difference looks like noise. In our identification scheme, the invisible noises are estimated with the wiener-filter and the 2D Discrete Wavelet Transform (DWT) filter. Then, a gray level co-occurrence matrix (GLCM) is calculated to analyze the texture of the noise. From the GLCM, 384 statistical features are extracted and applied to train and test the support vector machine classifier for identifying the color laser printers. In the experiment, a total of 4,800 images from 8 color laser printer models were used, where half of the image is for training and the other half is for classification. Results prove that the presented algorithm performs well by achieving 99.3%, 97.4% and 88.7% accuracy for the brand, toner and model identification respectively.     

AptaCDSS-E: A classifier ensemble-based clinical decision support system for cardiovascular disease level prediction

Conventional clinical decision support systems are generally based on a single classifier or a simple combination of these models, showing moderate performance. In this paper, we propose a classifier ensemble-based method for supporting the diagnosis of cardiovascular disease (CVD) based on aptamer chips. This AptaCDSS-E system overcomes conventional performance limitations by utilizing ensembles of different classifiers. Recent surveys show that CVD is one of the leading causes of death and that significant life savings can be achieved if precise diagnosis can be made. For CVD diagnosis, our system combines a set of four different classifiers with ensembles. Support vector machines and neural networks are adopted as base classifiers. Decision trees and Bayesian networks are also adopted to augment the system. Four aptamer-based biochip data sets including CVD data containing 66 samples were used to train and test the system. Three other supplementary data sets are used to alleviate data insufficiency. We investigated the effectiveness of the ensemble-based system with several different aggregation approaches by comparing the results with single classifier-based models. The prediction performance of the AptaCDSS-E system was assessed with a cross-validation test. The experimental results show that our system achieves high diagnosis accuracy (>94%) and comparably small prediction difference intervals (<6%), proving its usefulness in the clinical decision process of disease diagnosis. Additionally, 10 possible biomarkers are found for further investigation.