Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

An efficient method for developing requirement specifications for plant control software using a component-based software prototype

This paper proposes an efficient method to develop requirement specifications for Plant Control Software (PCSW) using software-component-based prototypes. Prior to this proposal, domain analyses were conducted on existing PCSWs, and their functions were classified into “similar functions” and “individual functions”. Then PCSW Software Components (PSC: PCSW Software Component, PSCs: PCSW Software Components) were developed to correspond to these functions. PSCs as parameter-style components were developed in order to satisfy the clients’ (we define clients as owners, managers and operators of plants) requirements. A support environment for developing requirement specifications was developed. The environment consists of the Prototype Development Tool (PDT), the Behavior Check Simulator (BCS) and the Requirement Specification Development Tool (RSDT). The method consists of four steps. In the first step, PDT is used to define the parameters to customize PSCs and to compose a PCSW prototype by setting these parameters to PSCs. In the second step, BCS is used to execute the composed PCSW prototype and check its behavior and relevancy against the clients’ expectations. In the third step, steps 1 and 2 are repeated until the behavior of the PCSW prototype satisfies the clients’ requirements. Finally, a requirement specification is developed from the PCSW prototype which fully reflects the clients’ requirements. In order to evaluate the proposed method, it has been applied in five development cases. A Requirement Coverage of 91%, a Requirement Revision Rate of 6%, a PSC Reuse Rate of 92% and a LOC Reuse Rate of 83% have been achieved. In addition, a reduction of 55% in the amount of time required to develop requirement specifications has been achieved. These results indicate that the proposed method has sufficient capability to develop an exhaustive and an adequate PCSW requirement specification. And the developed PSCs have sufficient functions and capability to compose PCSW prototypes, and the support environment is capable of shortening the time taken to develop requirement specifications.     

Nickel Electroplating

NICKEL ELECTROPLATING has been practicallyused for decades.There is an unknown part in theplating,although this is easy to plate.Applications ofthe plating are described from the practical viewpoint.Purpose of Nickel Electroplating(1)Decorative,and corrosion resistanceNickel electroplating is deposited on iron,cupper,zinc and aluminum substrate etc.,and chromiumplating is usually deposited on nickel plating.Hexavalent chromium plating has an important effecton the corrosion resisitan…     

The evaluation of speckle contrast with variable speckle generator

Abstract— While laser projection has many advantages, there is a problem with speckle patterns generated as a result of interference of the laser beam and results in bad effects to observers. In 2010, a variable speckle generator, which produces an angular shift of incident light to the screen and generates variable speckle patterns, was suggested. In this study, the performance of a variable speckle generator by using a volume phase holographic beam shaper and scanning mirror was investigated in detail by evaluating both the objective and subjective speckle contrast. The morphology of the speckle pattern was also investigated when the variable speckle generator was activated. With a scanning VPH beam shaper, the objective speckle was effectively reduced because each point of the VPH beam shaper generated different speckle patterns and coherency among each pattern disappeared by using the scan process. On the other hand, subjective speckle was also dramatically reduced by changing the incident angle on the screen, which resulted in generating variable subjective speckle. It was also shown that the speckle reduction rate by using a variable speckle generator did not depend on the coherent length of a laser by evaluating the normalized speckle contrast against the angular shift on the screen.     

Recovery of Precious and Base Metals from Waste Printed Circuit Boards Using a Sequential Leaching Procedure

This paper considers the issue of recycling of waste printed circuit boards (WPCBs) containing precious and base metals in appreciable amounts. High-pressure oxidative leaching (HPOL) with dilute sulfuric acid resulted in removal of a significant amount of base metals from a WPCB ash sample obtained by incineration at 800°C. The parameters investigated in the precious metal leaching from WPCB residue after HPOL included the sulfuric acid concentration, thiourea concentration, oxidant concentration, leaching temperature, and leaching time. Recovery of gold, silver, and palladium of 100%, 81%, and 13% from the WPCB residue sample was achieved by thiourea leaching under optimized conditions. The results show that the efficiency of precious metal dissolution from the WPCB sample using thiourea solution depended strongly on the concentration of both thiourea and oxidant.     

Nonsolvent coal hydrogenation at short contact time

Yields and properties of products on hydrogenation of Japanese and Australian coals have been studied using an autoclave equipped with a magnedrive device at temperatures of 500–600 °C and hydrogen pressure 4.9–14.7 MPa (gauge) in the absence of solvent. Optimum contact time, at which maximum extraction yield was observed, shifted from 15 s to a few seconds with increasing reaction temperature and hydrogen pressure. The extracts derived from both coals reveal similar structural parameters.     

Theoretical studies on VPI-5. 3. The MS-Q force field for aluminophosphate zeolites

Aluminophosphate zeolite is an artificial material which shows strange hydrophilicity. We have been investigating the reason by quantum mechanics, and found that the hydrophilicity of this zeolite depended on the local geometric deformation, and speculated that the site-specific hydrophilicity might be explained by differences in the stiffness of the local deformation determined by the location with the pore structure. In order to test these ideas, we construct a reliable force field based on the new MS-Q approach developed by Demiralp, Cagin, and Goddard. Our force field well reproduces the experimental structure of VPI-5.     

Improvement of anode oxidation reaction of a fuel cell using ammonium formate with Pt‐Ir catalysis

We have attempted to develop high‐performance and safe fuel cells by using ammonium formate as a solid (powder) fuel. This solid fuel has the potential of safer transportability than liquid fuels such as methanol from the viewpoint of toxicity and flammability. In order to make use of some of the advantages of ammonium formate, we investigated the oxidation characteristics of ammonium formate with respect to a Pt electrode. Cyclic voltammograms indicate that ammonium formate has high oxidation activity with respect to a Pt electrode. We have also found that the oxidation of ammonium formate can be improved by the addition of Ir to Pt catalysts. It is highly likely that ammonium formate will be useful as a solid (powder) fuel for polymer electrolyte membrane (PEM) fuel cells. This new fuel will promote the development of safe fuel cells for PEM. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(4): 45–50, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21043     

Ethological data mining: an automata-based approach to extract behavioral units and rules

We propose an efficient automata-based approach to extract behavioral units and rules from continuous sequential data of animal behavior. By introducing novel extensions, we integrate two elemental methods—the N-gram model and Angluin’s machine learning algorithm into an ethological data mining framework. This allows us to obtain the minimized automaton-representation of behavioral rules that accept (or generate) the smallest set of possible behavioral patterns from sequential data of animal behavior. With this method, we demonstrate how the ethological data mining works using real birdsong data; we use the Bengalese finch song and perform experimental evaluations of this method using artificial birdsong data generated by a computer program. These results suggest that our ethological data mining works effectively even for noisy behavioral data by appropriately setting the parameters that we introduce. In addition, we demonstrate a case study using the Bengalese finch song, showing that our method successfully grasps the core structure of the singing behavior such as loops and branches. Yasuki Kakishita and Kazutoshi Sasahara have contributed equally to this work.     

Incorporation of a well-defined polyether side-chain into segmented poly(ether-urethane urea) and examination for blood-compatibility

A new method of introducing a hydrophilic polyether side chain into segmented polyurethane using a polypropylene oxide macromer with 1,3-diol at one chain-end, which behaves as chain extender, is described. In this procedure, a molecular-designed side-chain is incorporated quantitatively and directly into polyurethane biomedical elastomer. The design is also of interest to biomaterials in artificial organs.