Supply chain network design using an integrated neuro-fuzzy and MILP approach: A comparative design study

In this study, an integrated supply chain (SC) design model is developed and a SC network design case is examined for a reputable multinational company in alcohol free beverage sector. Here, a three echelon SC network is considered under demand uncertainty and the proposed integrated neuro-fuzzy and mixed integer linear programming (MILP) approach is applied to this network to realize the design effectively. Matlab 7.0 is used for neuro-fuzzy demand forecasting and, the MILP model is solved using Lingo 10.0. Then Matlab 7.0 is used for artificial neural network (ANN) simulation to supply a comparative study and to show the applicability and efficiency of ANN simulation for this type of problem. By evaluating the output data, the SC network for this case is designed, and the optimal product flow between the factories, warehouses and distributors are calculated. Also it is proved that the ANN simulation can be used instead of analytical computations because of ensuring a simplified representation for this method and time saving.     

Vaccination with glutaraldehyde-fixed bovine respiratory syncytial virus (BRSV)-infected cells stimulates a better immune response in lambs than vaccination with heat-inactivated cell-free BRSV

The lamb model was used to investigate the possible protective effects of vaccination with inactivated viral antigens against experimental infection with bovine respiratory syncytial virus. Two groups of eight lambs were vaccinated with either glutaraldehyde-inactivated cell-associated virus or heat-inactivated cell-free virus and subsequently challenged with live virus, along with a group of naive lambs. The virus was shed for significantly longer periods, and the virus titres in nasal secretions were significantly higher in the group of naive lambs than in the two groups of vaccinated lambs. The period of virus-shedding in nasal secretions and virus titres was significantly lower (p < 0.01) in the group of lambs immunized with the cell-associated preparation. The same antigen stimulated better cellular immune responses as measured by virus-specific cytotoxicity or by virus-specific lymphocyte proliferation. However, priming with inactivated vaccines had no significant effect on lymphocyte responses to phytohaemagglutinin, which was found to be significantly reduced (p < 0.01) following challenge with live virus.     

Mode I fracture toughness determination with straight notched disk bending method

A new method called the straight notched disk bending method is developed for mode I fracture toughness determination using rock cores. Disk specimens of andesite and marble having a single straight edge notch were subjected to three-point bending loads. Dimensionless stress intensity factor estimations and fracture toughness tests were conducted for different notch lengths, span lengths, thicknesses and diameters of the cylindrical rock specimens. Stress intensity factors were computed by three-dimensional finite element modeling and the results were presented for a wide range of specimen geometrical parameters. Results of experiments were compared to the results of well-known mode I fracture toughness testing methods. For specimens having thickness equal to the radius, mode I fracture toughness was lower and close to the results obtained by semi-circular bending method. When thickness was increased and doubled, mode I fracture toughness increased and approached to the value found by the suggested cracked chevron notched Brazilian disk method. Advantages of the new method included easy specimen preparation and testing procedure, stiffer specimen geometry, smaller fracture process zone, and flexibility of the specimen geometry for the investigation of the size effect behavior.     

Laser cutting of 7050 Al alloy reinforced with Al2O3 and B4C composites

In the present study, laser cutting of 7050 aluminum alloy sheets reinforced with Al₂O₃ and B₄C particles are carried out. The cut geometry is examined using scanning electron microscope and the optical microscope. The lump parameter analysis technique is used to formulate and determine the kerf width size. The predictions for kerf width are compared with experimental data. The percentage kerf width size variation along the cut edges is determined and the influence of the laser power level and duty cycle of the laser pulses on the percentage kerf width size variation is examined. It is found that 7050 aluminum alloy reinforced with 20% Al₂O₃ composite results in relatively large kerf width size as compared to its counter parts that corresponding to 7050 aluminum alloy reinforced with 20% B₄C composite. The kerf width size predicted agreed with the experimental data for both composites.     

The development of the German energy market until 2030—A critical survey of selected scenarios

Many scenarios have been generated in the last years analysing the international energy market. The variety of these scenarios is manifold, as they are generated by different institutions using different methodological approaches and different framework assumptions. However, these scenarios can roughly be classified into three main groups: “moderate”, “climate protection” and “resource scarcity and high fossil fuel prices”. Analysing the German energy market makes a fourth scenario group necessary, which considers the possible revision of the decided nuclear energy phase out. Most of the existing scenarios developed by different institutions can be allocated into one of these groups. A representative scenario for each group has been selected to illustrate the development of the energy sector until 2030. Contrary to the worldwide primary energy demand (PED), the German PED decreases in each scenario, even though the drop differs strongly throughout the scenarios. On the other hand the structure of the PED in 2030 varies strongly for each scenario, especially regarding the share of fossil energy sources. However, a common robust result can be observed throughout all scenarios, namely the high increase in the share of the renewable energy resources, although the scenario generation processes are not always robust.     

Investigation of proper specimen geometry for mode I fracture toughness testing with flattened Brazilian disc method

Investigation of geometrical parameters for flattened Brazilian disc method is important, since this is a simple and attractive method for mode I fracture toughness testing on rock cores. Evaluating numerical modeling results, a parametric equation in terms of principal stresses at the center of the disc and the loading angle of the flattened end was developed. An equation was proposed for maximum stress intensity factors at critical crack lengths around stable to unstable crack propagation. Comparing fracture toughness results of flattened Brazilian disc method to the results of the suggested cracked chevron notched Brazilian disc method, geometrical parameters for flattened Brazilian discs were investigated. Diameter, loading angle of flattened ends, and thickness of andesite rock core specimens were changed to obtain comparable results to the suggested method. The closest results to the suggested method were obtained by 54 mm diameter discs with loading angles larger than 32°, and thicknesses between 19 and 34 mm. Results were confirmed by the flattened Brazilian disc tests on a marble rock. In flattened Brazilian disc tests with smaller loading angles and larger diameters, larger fracture toughness values than the results of the suggested cracked chevron notched were obtained. However, excluding tests with large loading angles over 27°; specimen size was less effective on the results of these tests. Critical crack length parameters computed from modeling and experiments were close to each other for the flattened Brazilian disc specimens with smaller loading angles around 20° and thickness/radius ratio equal or less than 1.1.     

Laser cutting of small diameter hole in aluminum foam

The International Journal of Advanced Manufacturing Technology - Laser cutting of a small diameter hole into aluminum foam is carried out, and thermal stress field developed in the cutting section...