Prolonged degradation of end-capped polyelectrolyte multilayer films

Cationic chitosan (CT) and anionic dextran sulfate (Dex) were layer-by-layer (LbL) assembled from aqueous solutions containing 1 M NaCl on a quartz crystal microbalance (QCM) substrate, and the original films ((CT-Dex)₃-CT)) were end-capped with LbL assembly from CT solutions containing 1 M NaCl and Dex solutions without NaCl. The enzymatic degradation of films by chitosanase was quantitatively analyzed by QCM in terms of numbers of end-capping steps. The degradation of films end-capped with (Dex-CT)₃ was considerably prolonged when compared to those end-capped with other end-capping steps. A mechanism for the prolonged degradation was proposed by quantitative QCM data and zeta potential results.     

Syngas production by biomass gasification using Rh/CeO2/SiO2 catalysts and fluidized bed reactor

We have been developed novel catalysts for gasification of biomass with much higher energy efficiency than conventional methods (non-catalyst, dolomite, commercial steam reforming Ni catalyst). From the result of the gasification of cellulose over novel Rh/CeO₂/SiO₂ catalysts, it is found that the gasification process consists of the reforming of tar and the combustion of solid carbon. We also tested novel Rh/CeO₂/SiO₂ in the gasification with air, pyrogasification, and steam reforming of cedar wood. As a result, Rh/CeO₂/SiO₂ gave higher yield of syngas than the conventional steam reforming Ni catalyst. Furthermore, we compared the performance between single and dual bed reactors. Single bed reactor was effective in the gasification of cedar, however, it was not suitable for the gasification of rice straw since a rapid deactivation was observed. Gasification of rice straw, jute stick, baggase using the fluidized dual-bed reactor and Rh/CeO₂/SiO₂ was also investigated. Especially, the catalyst stability in the gasification of rice straw clearly was enhanced by using the fluidized dual bed reactor.     

Resistance to sulfur poisoning of hot gas cleaning catalysts for the removal of tar from the pyrolysis of cedar wood

In the partial oxidation of tar derived from the pyrolysis of cedar wood, the effect of H₂S addition was investigated over non-catalyst, steam reforming Ni catalyst, and Rh/CeO₂/SiO₂ using a fluidized bed reactor. In the non-catalytic gasification, the product distribution was not influenced by the presence of H₂S. Steam reforming Ni catalyst was effective for the tar removal without H₂S addition, however, the addition of H₂S deactivated drastically. In contrast, Rh/CeO₂/SiO₂ exhibited higher and more stable activity than the Ni catalyst even under the presence of high concentration of H₂S (280 ppm). On the Ni catalyst, the adsorption of sulfur was observed by XPS and Ni species was oxidized during the partial oxidation of tar. In the case of Rh/CeO₂/SiO₂, the adsorption of sulfur was below the detection limit of XPS. This can be related to the self-cleaning of catalyst surface during the circulation in the fluidized bed reactor for the partial oxidation of tar derived from cedar pyrolysis.     

Catalyst Design of Pt-Modified Ni/Al2O3 Catalyst with Flat Temperature Profile in Methane Reforming with CO2 and O2

Pt(0.3)/Ni(10)/Al₂O₃, prepared by a sequential impregnation method, exhibited a more excellent performance in methane reforming with CO₂ and O₂ in terms of the catalytic activity and the temperature profile of the catalyst bed than Pt(0.3) + Ni(10)/Al₂O₃ prepared by a coimpregnation method, Ni(10)/Al₂O₃, Pt(0.3)/Al₂O₃, and Pt(10)/Al₂O₃. It is thought that this is because the surface Pt atoms on Ni catalyst can contribute to the enhancement of the catalyst reducibility.     

Dietary eritadenine-induced alteration of molecular species composition of phospholipids in rats

The effect of dietary eritadenine, a hypocholesterolemic compound found in the mushroomLentinus edodes, on the fatty acid and molecular species profiles of phosphatidylcholine (PC) and phosphatidylethanolamine (PE) in the plasma and liver microsomes was investigated in relation to the hypocholesterolemic action of the compound in rats. Animals were fed the control or eritadenine-supplemented (50 mg/kg diet) diet for 14 d. Eritadenine supplementation significantly decreased the plasma concentrations of cholesterol and phospholipids, but not triglycerides. The PC/PE ratio of liver microsomes, but not plasma, was also markedly decreased by eritadenine. Eritadenine supplementation was found to increase the proportion of 18:2n-6 and, inversely, to decrease the proportion of 20:4n-6 and 22:5n-6 in plasma PC and liver microsomal PC and PE, indicating that eritadenine depressed the metabolism of linoleic acid. The effect of eritadenine on the profile of n-3 fatty acids was dissimilar in PC and PE. These changes in fatty acid composition were selectively reflected in the molecular species composition of both PC and PE; the extent of increase in 16:0–18:2 molecular species or decrease in 18:0–20:4 molecular species was apparently greater than that of other molecular species containing 18:2 or 20:4 in the sn-2 position. These results suggest that, in addition to the decrease in liver microsomal PC/PE ratio, the alteration of plasma PC molecular species composition might also participate in the hypocholesterolemic action of eritadenine.     

Elevation of plasma levels of L-dopa in transdermal administration of L-dopa-butylester in rats

To increase delivery of L-dopa in its transdermal absorption, a new lipophilic derivative of L-dopa, L-dopa-butylester, was synthesized. An in-vitro study employing two-chamber diffusion cells, in which the excised rat abdominal skin was mounted, revealed that, in the presence of L-menthol and ethanol, L-dopa-butylester penetrated in its original form more effectively than L-dopa. L-Dopa-butylester sheets were made by immersing wiper sheets in methanol containing the compound, and then evaporating the methanol. An extraction study of the compound from the sheets revealed that its stability was maintained for at least 12 weeks. In an in-vivo cutaneous absorption study, an L-dopa-butylester sheet was attached to the shaved rat abdominal skin. A hydrogel containing L-menthol and ethanol was spread on vinyl tape, and this sheet was placed over it. In plasma, the L-dopa level rose linearly between 30 and 180 min after the cutaneous application; L-dopa-butylester was not detected. The L-dopa level was higher than that in which L-dopa was applied. These findings indicated that the lipophilic nature of L-dopa-butylester further increased its penetration through the skin, and that L-dopa-butylester that was taken up into the general circulation system was rapidly converted to L-dopa by hydrolysis in the body.     

Development Of Cvt Control System And Its Use For Fuel‐Efficient Operation Of Engine

Continuously variable transmission (CVT) provides an automobile with the ability to change the gear ratio continuously, which can then improve not only ride quality such as acceleration performance but also fuel‐efficiency. However, to take advantage of the ability, a control system that can precisely control the gear ratio is required. This paper proposes such a control system for a belt‐driven CVT system. For controller design, first the CVT system is modeled by analytical and experimental approaches. The resultant static and dynamic characteristics provide a nonlinear first‐order model with an uncertain time constant and time delay. The nonlinear steady‐state gain is adjusted to one by a gain‐scheduled pre‐compensator. Thereby the plant model becomes a linear first‐order lag system with a dead time. The next step is controller design using the plant model. To guarantee stability and control performance against the parameter variation and time delay, the μ‐synthesis, a robust control method, is employed for feedback control. In addition, a feedforward controller is incorporated into the feedback control system to obtain better output response. The feedforward controller is given by a combination of the inverse system of the plant and a reference model that gives desired output response. As a result, the control system becomes a two‐degree‐of‐freedom control system. To evaluate the performance of the control system and its effectiveness on the fuel‐efficiency, computer simulation and driving tests were conducted. The simulation and experiment results prove that the proposed control system can make the gear ratio track a reference output quickly and precisely in the presence of the uncertainties. The results also show that the control system improves fuel‐efficiency by changing the gear ratio so that the engine torque and its revolution speed can satisfy optimum‐efficiency operating condition.     

Efficient selection of hybrids by protoplast fusion using drug resistance markers and reporter genes in Saccharomyces cerevisiae

We have developed a selection system for hybrids by protoplast fusion using dominant selective drug resistance markers, Tn601(903) against geneticin and AUR1-C against aureobasidin A, and reporter genes, ADH1p-PHO5-ADH1t and CLN2p-CYC1-lacZ, in Saccharomyces cerevisiae. To examine the effectiveness of this system, plasmids with each marker and reporter gene were introduced into auxotrophic sake yeasts. From the resulting transformants, eight colonies were screened by protoplast fusion in combination with the drug resistance markers and the reporter genes. Among them, seven strains were judged as hybrids between parental strains by analysis of growth on a minimal medium. This selection system was applied to wine yeasts having no genetic markers. Six strains were regarded as hybrids between parental strains by polymerase chain reaction/restriction fragment length polymorphism (PCR/RFLP) analysis of the MET2 gene and by karyotype analysis using a contour-clamped homogeneous electric field (CHEF). We propose that the plotoplast fusion using dominant selective geneticin- and aureobasidin A-resistance markers and reporter genes is useful for the selection of hybrids from wine yeasts, which are homothallic and have low sporulation ability.     

Epitaxial growth of titanium oxide thin films on MgO(100) single-crystal substrates by reactive deposition methods

We synthesized titanium oxide thin films on MgO(100) single-crystal substrates by two reactive deposition methods and compared the structures of the thin films formed by these methods. In one method (pulsed-molecular-beam deposition method), molecular oxygen is supplied to the substrates by using a pulsed-molecular-oxygen beam source and deposition of one unit layer of titanium and subsequent supply of molecular oxygen are repeatedly performed. In the other method (radical beam deposition method), atomic oxygen is irradiated to the substrates by using an atomic oxygen beam generated by the radical beam source and irradiation of the atomic oxygen and deposition of titanium are simultaneously performed. In the case of the pulsed-molecular-beam deposition method, the crystal structure was changed by increasing the number of oxygen pulses supplied from the beam source. We found that the crystal structure of titanium oxide depended on the composition ratio of O:Ti in the film. The maximum ratio of O:Ti attainable by this method was 1.85, and at this ratio, (100)-oriented pseudorutile was formed. In the case of the radical beam deposition method, (100)-oriented anatase was formed below the titanium deposition rate of 0.10 nm/s and pseudorutile (TiO_2−δ) was formed above 0.15 nm/s. The pseudorutile structure synthesized on this experiment was very stable in air. We concluded that the crystal structure of the pseudorutile is a new crystal structure of titanium oxide.