Comprehensiveness and uniqueness of commercial databases and open access systems

Scientometrics - In this study, scholarly communication systems provided by commercial services and open access systems are examined on the basis of the comprehensiveness and uniqueness of their...     

Degree-of-polarization and eye-closure penalty associated with optical signals with orthogonal polarizations

We perform a systematic measurement of the degree-of-polarization (DOP) and eye-closure penalty for optical signals with orthogonal polarizations. We find that the symmetry of DOP is maintained for the orthogonal polarizations under both first and higher order polarization-mode dispersion (PMD), whereas the symmetry of eye-closure penalty is broken under second-order PMD. An orthogonal polarization pair can have large disparity of eye-closure penalty despite an identical DOP. We also demonstrate a novel approach to estimate the maximum eye-closure penalty asymmetry with three orthogonal polarizations on the Poincare/spl acute/ sphere.     

Poly(3-octylthiophene) as semiconductor for schottky barrier: Effects of doping and storage time

Schottky diodes of aluminium/poly(3-octylthiophene)(P30T)/indium-tin oxide with large active area are prepared by using the proposed new casting technique. Their rectifying behavior and junction characteristics are dependent on whether the P30T is doped and on the storage time, but independent of the thickness of the P30T layer. The present technique can also be applied in a fabrication of electronic devices with other soluble conjugated polymers.     

台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Structural and Superconducting Property Variations with Nominal Mg Non‐Stoichiometry in MgxB2 and Its Enhancement of Upper Critical Field

By applying a combination of characterisation tools, changes in structural and superconducting properties with nominal Mg non‐stoichiometry in Mg_xB₂ are found. The non‐stoichiometry produces enhanced in‐field critical current densities (J_c's) and upper critical field / irreversibility field (H_c2/H_irr(T)) values. Upper critical fields of ～ 21 T (4.2 K) were obtained in nominal Mg‐deficient samples compared to ～ 17 T (4.2 K) for near‐stoichiometric samples.     

Analytical pyrolysis as a tool for the study of plastic coals

The technique of analytical pyrolysis has been used to characterize 40 similar mid-rank western Kentucky coals of widely differing ASTM Gieseler plasticity. Certain pyrolysis/g.c. variables were shown to correlate well with both ASTM Gieseler and isothermal plasticity. Highly plastic coals were shown to exhibit certain characteristic peaks in the 450 °C pyrogram which were absent in the pyrogram of the non-plastic coals. Two coals, representing the two extremes in plasticity, were selected for further study. After extraction with solvents such as DMF the characteristic peaks were absent in the 450 °C pyrogram of the extraction residue of the highly plastic coal. These peaks were also shown to decrease with increasing severity of air oxidation of the plastic coal. This technique appears to be a useful tool for the analysis of mid-rank plastic coals and supports the view that the substances contained in the bitumen fraction of these coals are involved in the development of the plastic state.     

Association of INAD with NORPA is essential for controlled activation and deactivation of Drosophila phototransduction in vivo

Visual transduction in Drosophila is a G protein-coupled phospholipase C-mediated process that leads to depolarization via activation of the transient receptor potential (TRP) calcium channel. Inactivation-no-afterpotential D (INAD) is an adaptor protein containing PDZ domains known to interact with TRP. Immunoprecipitation studies indicate that INAD also binds to eye-specific protein kinase C and the phospholipase C, no-receptor-potential A (NORPA). By overlay assay and site-directed mutagenesis we have defined the essential elements of the NORPA-INAD association and identified three critical residues in the C-terminal tail of NORPA that are required for the interaction. These residues, Phe-Cys-Ala, constitute a novel binding motif distinct from the sequences recognized by the PDZ domain in INAD. To evaluate the functional significance of the INAD-NORPA association in vivo, we generated transgenic flies expressing a modified NORPA, NORPAC1094S, that lacks the INAD interaction. The transgenic animals display a unique electroretinogram phenotype characterized by slow activation and prolonged deactivation. Double mutant analysis suggests a possible inaccessibility of eye-specific protein kinase C to NORPAC1094S, undermining the observed defective deactivation, and that delayed activation may similarly result from NORPAC1094S being unable to localize in close proximity to the TRP channel. We conclude that INAD acts as a scaffold protein that facilitates NORPA-TRP interactions required for gating of the TRP channel in photoreceptor cells.     

Effects of the hob cutter regrinding and setting on ZE-type worm gear manufacture

A mathematical model for a ZE-type worm gear set is proposed. The characteristics of a ZE-type worm gear cut with an oversize hob cutter are investigated. Bearing contacts and kinematic errors in the ZE-type worm gear set due to regrinding of oversize hob cutters are also studied. Bearing contacts in the worm gear set were obtained using surface separation topology techniques and tooth contact analysis. It was found that bearing contact locations are sensitive to the hob cutter setting angle and setting distance. Kinematic error minimization was achieved modifying worm normal tooth angle. By applying the optimization theorem and computer simulation programs, optimum hob cutter settings and worm normal tooth angle were determined to improve bearing contact location and minimize the worm gear set kinematic errors. A numerical example is given to demonstrate the results of the investigation. The developed computer-aided manufacture program has successfully been applied to the worm gear manufacture and hob cutter design.