The effect of pack-aluminisation on the microstructure of MCrAlY and the performance of thermal barrier coatings

Plasma spraying and pack-aluminising processes were combined and applied to the nickel-base superalloy Mar-M247 to improve its cyclic oxidation resistance. The performance tests of duplex ZrO₂-8 wt.%Y₂O₃/MCrAlY thermal barrier coatings (TBCs) were conducted at 1050 °C, 1075 °C, 1100 °C, 1150 °C and 1200 °C. The results of the experiments in this study showed that TBC specimens with the aluminised MCrAlY bond coat exhibited higher cyclic lives (except for the Ni-22Cr-10Al-1Y bond coat), at all the temperatures tested, than specimens on which the bond coat was not aluminised. The microstructures of the Co-29Cr-6Al-1Y, Co-32Ni-21Cr-8Al-0.5Y and Ni-22Cr-10Al-1Y bond coats with or without aluminising treatment were examined in detail using a scanning electron microscope equipped with an electron probe microanalyzer.     

Robust controller with disturbance rejection for hydraulic servosystems

A controller is presented that improves the performance and reduces the sensitivity of hydraulic servo systems in the presence of parameter variations, nonlinear effects, and other disturbances. The control system has enhanced closed-loop stability and can recover from steady-state and transient error quickly and completely. It consists of a servo controller, an auxiliary controller, and a robust controller. Simulation and experimental results demonstrate the validity of the controller     

Effects of nano‐ and micro‐fillers and processing parameters on injection‐molded microcellular composites

The effects of submicron core‐shell rubber (CSR) particles, nanoclay fillers, and molding parameters on the mechanical properties and cell structure of injection‐molded microcellular polyamide‐6 (PA6) composites were studied. The experimental results of PA6 nanocomposites with 5.0 and 7.5 wt% nanoclay loadings and of CSR‐modified PA6 composites with 0.5 and 3.1 wt% CSR loadings were compared to their neat resin counterparts. This study found that nanoclay was more efficient in promoting a smaller cell size, larger cell density, and higher tensile strength for microcellular injection molding parts. A higher nanoclay loading led to more brittle behavior for microcellular parts. It was found that a proper amount of CSR particles could be added to the microcellular injection‐molded PA6 to reduce the cell size, increase the cell density, and enhance the toughness of the molded part. However, CSR particles were less effective cell nucleation agents as compared to nanoclay for producing desirable cell structures, and a higher CSR loading was found to have diminishing effects on the process and on the properties of the parts. POLYM. ENG. SCI., 45:773–788, 2005. © 2005 Society of Plastics Engineers     

Improved activity and thermostability of Candida antarctica lipase B by DNA family shuffling

DNA family shuffling was used to create chimeric lipase B proteins with improved activity toward the hydrolysis of diethyl 3-(3',4'-dichlorophenyl)glutarate (DDG). Three homologous lipases from Candida antarctica ATCC 32657, Hyphozyma sp. CBS 648.91 and Crytococcus tsukubaensis ATCC 24555 were cloned and shuffled to generate a diverse gene library. A high-throughput screening assay was developed and used successfully to identify chimeric lipase B proteins having a 20-fold higher activity toward DDG than lipase B from C.antarctica ATCC 32657 and a 13-fold higher activity than the most active parent derived from C.tsukubaensis ATCC 24555. In addition, the stability characteristics of several highly active chimeric proteins were also improved as a result of family shuffling. For example, the half-life at 45 degrees C and melting point (T(m)) of one chimera exceeded those of lipase B from C.antarctica ATCC 32657 by 11-fold and 6.4 degrees C, respectively, which closely approached the stability characteristics of the most thermostable parent derived from Hyphozyma sp. CBS 648.91.     

Comparison of a‐Si and Poly‐Si for AMOLED displays

Abstract— The characteristics of OLED backplanes including the intrinsic properties of a‐Si TFTs and LTPS TFTs will be reviewed. While LTPS TFTs reveal satisfactory stability in AMOLED‐display applications, a‐Si AMOLEDs show better uniformity and are capable of driving OLEDs. However, the stability of a‐Si TFTs under long‐term operation is still unacceptable and remains to be the key issue constraining the commercialization of a‐Si TFT AMOLEDs.     

One‐Step Fast Synthesis of Li4Ti5O12 Particles Using an Atmospheric Pressure Plasma Jet

A one‐step process to fabricate crystalline Li₄Ti₅O₁₂(LTO) particles directly from solution using an atmospheric pressure plasma jet (APPJ) is reported. This process uses Ti and Li ions‐containing salt solutions as the precursor, which is ultrasonically nebulized and then transported to the downstream of the APPJ using a carrier gas. With an extremely short contact time (<0.1 s) between the precursor droplets and the plasma jet, crystalline LTO can be fabricated in one step without additional rinse and postannealing steps. The LTO particle size can be effectively controlled using a preheater, the precursor solution composition and concentration, and the carrier gas flow rate. By properly adjusting the operating condition, particles of diameters from 100 nm to few μm with various morphologies can be obtained. When used as an electrode material, the resulting LTO powders fabricated under selected conditions show specific capacities over 100 mAh/g even at 50 C rate.     

A fast IP lookup scheme for high speed routers

Abstract

One of the key design issues for the next generation of IP routers is the IP lookup mechanism. IP lookup is an important action in a router, that is, to find the next hop for each incoming packet with a longest‐prefix‐match address in the routing table. In this paper, we propose an IP lookup mechanism with the number of memory accesses for an IP lookup being one in the best case and being four in the worst case. The forwarding table needed by our mechanism is small enough to fit in the SRAM. For example, a large routing table with 40000 routing entries can be compacted to a forwarding table of 260KBytes in our scheme.     

Fabrication of super‐ductile PP/LDPE blended parts with a chemical blowing agent

The mechanical blending of polypropylene (PP) and low density polyethylene (LDPE) is an economical and simple method for producing new polymeric materials for specific applications. However, the reduction in strain‐at‐break of the blend is one of its main shortcomings. In this study, PP/LDPE foamed parts were fabricated by conventional injection molding (CIM) with azodicarbonamide as a chemical blowing agent (CBA) and tested for tensile properties at two test speeds. Also, the fracture surfaces of the parts were investigated by scanning electron microscopy (SEM). In addition, to investigate the underlying mechanism of the super‐ductility, the tested samples were carefully analyzed and compared, and further characterized by differential scanning calorimetry and SEM. The results suggest that fabricating PP/LDPE super‐ductile parts using CIM with a CBA is feasible. The results also indicate that there is a close relationship between the mechanical properties and morphological structures, which are deeply influenced by the dosage of CBA, the PP/LDPE ratio, and the packing parameters. Furthermore, compared to conventional injection molded solid parts, the ductility of the foamed parts can be dramatically improved by the formation of microfibrils in the PP phase, which come into being under certain processing conditions. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44101.     

Experimental study on the penetration interfaces of pipes with different cross‐sections in overflow water‐assisted coinjection molding

The residual wall thicknesses (RWT) of the skin and the inner layers are important quality indicators of water‐assisted co‐injection molding (WACIM) parts. The influences of the shape of the cavity cross section and the processing parameters, including the water pressure, water delay time, inner melt temperature, and inner melt flow rate, on the penetration of the inner melt and water were explored via experiments. The results showed that the shape of the penetration section of the inner melt was closer to the cavity section with round corners, while that of the water ended up being round. Both the penetration ratios of the inner melt and the water increased proportionally with increasing circle ratio. Both the minimum values of the total RWT and the inner melt RWT increased with increasing circle ratio. Both the maximum values of the total RWT and the inner melt RWT increased with increasing Max_D, which is the maximum distance between the inscribed circle center and the wall. Both the penetration ratios of the inner melt and the water increased with increasing water pressure, decreased with increasing water delay time, and increased with increasing inner melt flow rate and increasing inner melt temperature. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42866.