Fractionation of transgenic corn for recovery of recombinant enzymes

Two germ-separation methods, dry-milling and density separation by flotation, were evaluated for recovering recombinant β-glucuronidase (rGUS) that accumulated primarily in the germ of transgenic corn. The dry-milling process consisted of (i) seed tempering, (ii) degerming with a horizontal-drum degermer/dehuller, (iii) particle size fractionation with standard sieves, (iv) germ and endosperm separation by roller milling and sifting, and (v) removal of hulls by aspiration. Sieves nos. 5, 6, and 7 retained the majority of germ, and subfractions from these sieves were pooled as a germ-rich fraction. Mass balances showed that the germ-rich fraction, which constituted 17% of the total dry-milled corn weight, contained 49% of rGUS activity and 64% of the total recoverable oil. Germ fractionation by flotation was tested as a proof-of-concept method aimed at separating corn fractions based on their difference in specific gravity (sp gr). The process consisted of impact-grinding of corn kernels followed by density separation using 1.15 or 1.3 specific gravity sodium nitrate solution. The oil-containing germ fraction floated, whereas the heavier endosperm fraction sedimented. The flotation method was simpler and resulted in higher enzyme recovery, that is, the germ-rich fraction was 20% (w/w) of the initial corn weight, and accounted for 80% of rGUS activity and 77% of total oil. The sodium nitrate solution did not have an adverse effect on the enzyme activity.     

Noise analysis of robot manipulator using neural networks

Due to a lot of robot manipulators application in industry, low noise degree is very important criteria for robot manipulator's joints. In this paper, joint noise problem of a robot manipulator with five joints is investigated both theoretically and experimentally. The investigation is consisted of two steps. First step is to analyze the noise of joints using a hardware and software. The hardware is a part of noise sensors. The second step; according to experimental results, some neural networks are employed for finding robust neural noise analyzer. Five types of neural networks are used to compare each other. From the results, it is noted that the proposed RBFNN gives the best results for analyzing joint noise of the robot manipulator.     

Approximate periodic solutions for the Helmholtz-Duffing equation

Approximate periodic solutions for the Helmholtz-Duffing oscillator are obtained in this paper. He’s Energy Balance Method (HEBM) and He’s Frequency Amplitude Formulation (HFAF) are adopted as the solution methods. Oscillation natural frequencies are analytically analyzed. Error analysis is carried out and accuracy of the solution methods is evaluated.     

The modeling of mode choices of intercity freight transportation with the artificial neural networks and adaptive neuro-fuzzy inference system

Mode choice modeling is probably the most important element of transportation planning. It affects the general efficiency of travel and the allocation of resources. The development of mode choice models has recently witnessed significant advances in many fields, such as passenger and freight transport. A large number of mathematical models have been used to model the traveler’s choice of mode and destination and the shipper’s choice of mode, shipment size and supply market, among others. Such models are not only becoming almost intractable but also data intensive, difficult to calibrate and update, and intransferable. These models cover a wide range of mathematical complexity and accuracy. This paper describes a new approach to mode choice of intercity freight transport modeling using artificial neural networks (ANNs) and adaptive neuro-fuzzy inference system (ANFIS) models. The new approach combines the learning ability of artificial neural networks and the transparent nature of fuzzy logic. The approach is found to be highly adaptive and efficient in investigating non-linear relationships among different variables. The adaptive neuro-fuzzy inference system model is tested on the freight transport market in Turkey, Germany, France and Austria by using information on the freight flows and their attributes. The ANNs and ANFIS models are more successful in the representation of the non-linear behavior of mode choice of intercity freight transport compared to the classical models.     

Dielectric properties of sol-gel derived Ta2O5 thin films

The dielectric constant and the dielectric loss of tantalum pentoxide (Ta₂O₅) thin films, produced by sol-gel spin-coated process on Corning glass substrates, have been investigated in the frequency range of 20-10⁵ Hz and the temperature range of 183-403 K, using ohmic Al electrodes. The frequency and temperature dependence of relaxation time has also been determined. The capacitance and loss factor were found to decrease with increasing frequency and increase with increasing temperature. The activation energy values were evaluated and a good agreement between the activation energy values obtained from capacitance and dielectric loss factor measurements were observed.     

Investigation of Al-O-Al sites in an Na-aluminosilicate glass

This paper reports the presence of Al- O- Al linkages in an aluminosilicate glass where Si/Al = 1 by using 2D¹⁷O triple quantum MAS NMR technique (3Q MASNMR). The experiments were performed at external magnetic fields of 8.4 and 14.4T. Despite¹⁷OMAS NMR spectra of the sample in both fields do not give much information about the different kinds of linkages in the sample, 3Q MAS NMR spectrum shows clear evidence that there are some amounts of Al-O-Al linkages in the sample giving two completely resolved peaks. These two peaks were attributed to the Si-O-Al and Al-O-Al linkages on the basis of their chemical shifts and, quadrupolar coupling constants which are quite sensitive to the local structure.     

Effects of annealing on the structural and magnetic properties of flame spray pyrolyzed MnFe2O4 nanoparticles

In this study, manganese ferrite (MnFe₂O₄) nanoparticles were produced through flame spray pyrolysis (FSP). To investigate the effects of heat treatment, the nanoparticles were annealed between 400 and 650°C for 4 h in air in a comparative manner. The structural, chemical, morphological, and magnetic properties of the nanoparticles were evaluated using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), dynamic light scattering (DLS), and vibrating sample magnetometry (VSM), respectively. The XRD results showed that the nanoparticles synthesized by the FSP method exhibited the MnFe₂O₄ spinel ferrite structure. The annealing process led to the decomposition of MnFe₂O₄ into various phases. According to the morphological analysis, the as-synthesized particles were hemispherical–cubic in shape and had an average particle size of less than 100 nm. In addition, the chemical bond structures of the nanoparticles were confirmed in detail by XPS elemental analysis. The highest saturation magnetization was recorded as 33.50 emu/g for the as-produced nanoparticles. The saturation magnetization of the nanoparticles decreased with increasing annealing temperature, while coercivity increased.     

Experimental and MD simulation study on the physical and mechanical properties of organically modified montmorillonite clay and compatibilized linear low density polyethylene nanocomposites

Understanding the interfacial interactions plays a key role in controlling mechanical and physical properties of polymer/clay nanocomposites (PCNs). In this work, the surface interactions between constituents of experimentally prepared PCNs which are the pristine linear low density polyethylene (PE) chains, PE compatibilizers, montmorillonite clay surface layer, and surfactants were studied quantitatively by employing molecular dynamics simulation technique. The interaction energy between the polymer and the clay was found to be inversely proportional with the volume of the surfactant which decreases the electrostatic interactions between the compatibilizer and the hydrophilic clay surface. However, the van der Waals (vdW) interactions between alkyl tails of surfactants and the PE chains increase with the tail length of the surfactants. The most attractive interaction was between the surfactant's head group and the clay surface. We showed that there existed fine balance between the electrostatic and vdW type forces on the stability and the enhanced properties of the PE–organoclay nanocomposites. Calculated interaction energies were then correlated to the experimentally measured mechanical properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45817.