The investigation of 32P wire for catheter-based endovascular irradiation

The dose distribution from a 32P source has been measured and calculated in order to evaluate its application in endovascular irradiation. The source dimension was 27 mm in length and 0.3 mm in diameter and was embedded in the end of a Ni-Ti wire. Dose measurements were performed using radiochromic film in several specially designed tissue equivalent phantoms. Loevinger's point dose kernel was used for the calculation. The approximate dose rate at a radial distance of 1.5 mm from the center of the source was found to be 6.75 cGy/s per GBq (0.25 cGy/s per mCi), which allows the delivery of a therapeutic dose in a short time interval with a satisfactory homogeneity without stepping the source. However, the dose rate falls off almost exponentially along the radial distance. Therefore it may not be suitable for treating large diameter vessel from a centrally located source. The effect of a curved 32P wire source on the radial dose distribution was also investigated. The results showed that for a maximum bend of 180 degrees the dose rate was increased by as much as 20% along the inner radial distance but decreased by as much as 20% along the outer radial distance compared to the dose along a straight wire. However, for curvatures normally encountered in a clinical situation, the dose rate was changed less than 5%.     

Challenges in computer architecture evaluation

We focus on problems suited to the current evaluation infrastructure. The current limitation and trends in evaluation techniques are troublesome and could noticeably slow the rate of computer system innovation. New research has been recommended to help and make quantitative evaluations of computer systems manageable. We support research in the areas of simulation frameworks, benchmarking methodologies, analytic methods, and validation techniques.     

Parametric study of the electrical to thermal power conversion in an inductively coupledrf plasma torch

An inductively coupled (ic) radio-frequency (rf) stabilized argon plasma was generated in a quartz tube using a 7 MHzrf generator. The electrical and thermal powers were measured and the efficiency of energy conversion was computed. The results indicate that for a constant power input, there is an optimum argon flow rate for which maximum energy conversion efficiency occurs.     

Copper coating on carbon fibres and their composites with aluminium matrix

A uniform and continuous coating of copper was given to carbon fibres by cementation or electroless techniques. In both cases, when coating thicknesses were less than 0.2 m, copper deposition was discontinuous over the fibres, and above 0.2 m, coatings were continuous. In electroless coating, about 75% of the continuously coated fibres had a coating thickness range 0.2–0.5 m and above this showed isolated dendrite deposits of copper. In the cementation process, about 75% of the continuously coated fibres had a coating thickness range 0.2–0.6 m, and above this thickness, fine crystallite-type copper deposition was found over smoothly coated copper. The ultimate tensile strength of continuously electroless-coated fibres were nearer to the uncoated fibres, suggesting defect-free coating, while fibres coated by the cementation process exhibited lower ultimate tensile strength values. The tensile fracture of both electroless- and cementation-coated fibres showed delamination of the coating, suggesting poor bonding between coating and the fibre. In composites, prepared by dispersing the coated chopped fibres in a pure aluminium matrix, uniform and random distribution of the fibres were observed without appreciable fibre-metal interaction. The CuAl₂ intermetallics were largely found in the matrix and only very small amounts were observed at fibre/matrix interfaces. Additions of about 2 wt% Mg to the matrix prior to the fibre dispersion did not appreciably change the distribution pattern of the fibres, but in addition to CuAl₂ phase, Mg₂Si phases were observed in the matrix as well as at the interface.     

石墨防爆片静态变形及应力分析

本文旨在通过对石墨防爆片的变形、应力分布及爆破压力的试验研究,探讨以石墨电极为原材料加工石墨防爆片的可行性。文中运用有限单元法及薄板理论对该防爆破片的应力分布做了初步分析,并以电测和爆破试验验证了以薄板理论为基础的爆破压力计算公式,可供进一步研究时参考。     

Morphology of craters at hypervelocity impact in isotropic composites with inclusions

Results of a study of hypervelocity impact in model disperse-reinforced composites with an epoxy or aluminum matrix with metallic (Al and Pb) or ceramic (SiO₂) inclusions are reported. The goal of the present study is to find materials that possess a higher resistance to penetration of a high-velocity projectile compared with materials of separate components. This resistance is characterized by the ratio of the depth of a crater in a sufficiently thick target to the diameter of a spherical projectile. For two composites studied, we show that in impact of a steel particle with a velocity ranging from3 to11km/sec, the crater depth is approximately one projectile diameter smaller than that for lead or aluminum targets. Lavrent’ev Institute of Hydrodynamics, Siberian Division, Russian Academy of Sciences, Novosibirsk 630090. Translated from Fizika Goreniya i Vzryva, Vol. 33, No. 3, pp. 139–151, May–June, 1997.     

Stearic acid unlike shorter-chain saturated fatty acids is poorly utilized for triacylglycerol synthesis and β-oxidation in cultured rat hepatocytes

Utilization of stearate as compared to various saturated fatty acids for cholesterol and lipid synthesis and β-oxidation was determined in primary culture of rat hepatocytes. At 0.5 mmol/L in the medium, stearate (18:0) adequately solubilized by albumin was less inhibitory to cholesterol synthesis from [2-¹⁴C] acetate than myristate (14:0) and palmitate (16:0) (68% vs. 91 and 88% inhibition, respectively). The rate of incorporation into cholesterol from [1-¹⁴C] stearate (3.0±0.6 nmol/mg protein/4 h) was 37-, 1.8-, and 7.8-fold of that from myristate, palmitate, and oleate, respectively. Conversely, the rate of [1-¹⁴C] stearate incorporation into total glycerolipids was 88–90% lower than that of labeled palmitate, myristate, and oleate. The rate of [1-¹⁴C] stearate incorporation into triacylglycerol (3.6±0.4 nmol/mg protein/4 h) was 6–8% of that from myristate, palmitate, oleate, and linoleate. The rate of stearate incorporation into phospholipids was the lowest among tested fatty acids, whereas the rate of mono- and diacylglycerol synthesis was the highest with stearate treatment. The rate of β-oxidation as measured by CO₂ and acid soluble metabolite production was also the lowest with [1-¹⁴C] stearate treatment at 22.7 nmol/mg protein/4 h, which was 35–40% of those from other [1-¹⁴C] labeled fatty acids. A greater proportion of stearate than other fatty acids taken up by the hepatocytes remained free and was not metabolized. Clearly, stearate as compared to shorter-chain saturated fatty acids was less efficiently oxidized and esterified to triacylglycerol in cultured rat hepatocytes.     

Multipath effects on vector tracking algorithm for GNSS signal

The vector tracking algorithm uses a single extended Kalman filter （EKF） to predict the time-delays and the Doppler deviations of the GNSS signal, while also estimating the user＇s position, velocity, and clock state. In this paper, the effects of multipath on the tracking performance of the vector delay / frequency lock loop （VDFLL） is studied for better application in the multipath environment. The error expressions of the measurements are given in theory. The tracking error caused by multipath is reduced by VDFLL, which is proved by the tracking error of VDFLL through a new iterating method. The theoretical analysis is verified by the Monte Carlo simulation.