A novel ceramic matrix composite based on YNbO4–TiO2 for microwave applications

This work presents the dielectric properties of YNbO₄ (YNO)–TiO₂ composites in the microwave range. X-ray diffraction analysis demonstrates that the addition of TiO₂ to YNO results in the formation of a Y(Nb_0.5Ti_0.5)₂O₆ phase. In the microwave range, the values of permittivity and dielectric loss did not present major changes with the increment of TiO₂. Moreover, the addition of TiO₂ results in an improvement in the thermal stability of YNO, with YNO63 demonstrating a resonant frequency of ?8.96 ppm.°C^?1. We utilised numerical simulations to evaluate the behaviour of these materials as dielectric resonator antennae and it is found that they exhibit a reflection coefficient below ?10 dB at the resonant frequency, with a realised gain of 4.94 – 5.76 dBi, a bandwidth of 665–1050 MHz and a radiation efficiency above 84%. Our results indicate that YNO–TiO₂ composites are interesting candidates for microwave operating devices.     

Increasing the photocatalytic and fungicide activities of Ag3PO4 microcrystals under visible-light irradiation

The present study reports for the first time the performance of silver phosphate (Ag₃PO₄) microcrystals as photocatalyst (degradation of Rodamine B-RhB) and antifungal agent (against Candida albicans–C. albicans) under visible-light irradiation (455 nm). Ag₃PO₄ microcrystals were synthesized by a simple co-precipitation (CP) method at room temperature. The structural and electronic properties of the as-synthetized Ag₃PO₄ have been investigated before and after 4 cycles of RhB degradation under visible light using X-ray diffraction (XRD), micro-Raman spectroscopy, UV–Vis spectrophotometer and field emission scanning electron microscopy (FE-SEM) images. The antifungal activity was analyzed in planktonic cells and 48h-biofilm of C. albicans by colony forming units (CFU) counting, confocal laser and FE-SE microscopies. Statistical analysis was carried out using SPSS software. Morphological and structural modifications of Ag₃PO₄ were observed upon recycling. After 4 recycles, the material maintained its photodegradation property; an eightfold increase in the efficiency of Ag₃PO₄ was observed in planktonic cells and a two fold increase in biofilm when irradiated under visible light. Thus, higher antifungal effectiveness against C. albicans was obtained when associated with visible-light irradiation.     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Extended preservation of raw beef and pork meat by hyperbaric storage at room temperature

Hyperbaric storage (HS) was evaluated as a new food preservation methodology at room temperature (RT) for beef and pork meat, both minced and in pieces, and compared to refrigeration (RF) storage. The meat samples were stored at 50, 75 and 100 MPa and variable RT up to 60 days. HS at 75 and 100 MPa could not only inhibit microbial growth but also inactivate microorganisms. Regarding physicochemical analyses, an overall equal to better pH maintenance in HS samples was achieved, and similar colour differences between HS and RF were observed. Generally, similarities in moisture content and drip loss between HS (mostly 75 and 100 MPa) and RF were detected (tendency for lower values in the former and higher values in the latter for the higher pressure level). Protein solubility revealed a decrease of sarcoplasmic protein values during storage with a pressure level dependency in some samples.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Synthesis and physicochemical characterization of a well-defined poly(butadiene 1,3)-block-poly(dimethylsiloxane) copolymer

For the first time, order-order and order-disorder transitions were detected and characterized in a model diblock copolymer of poly(butadiene-1,3) and poly(dimethylsiloxane) (PB-b-PDMS). This model PB-b-PDMS copolymer was synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene 1,3 (B) and hexamethylciclotrisiloxane (D₃), and subsequently characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size exclusion chromatography (SEC), Fourier Transform infrared spectroscopy (FTIR), Small-Angle X-ray scattering (SAXS) and rheology. SAXS combined with rheological experiments shows that the order-order and order-disorder transitions are thermoreversible. This fact indicates that the copolymer has sufficient mobility at the timescale and at the temperatures of interest to reach their equilibrium morphologies.     

Coupling GIS with Hydrologic and Hydraulic Flood Modelling

Geographic Information Systems (GIS) have been recognised as a powerful means to integrate and analyse data from various sources in the context of comprehensive floodplain management. As part of this comprehensive approach to floodplain management, it is very important to be able to predict the consequences of different scenarios in terms of flooded areas and associated risk. Hydrologic and hydraulic modelling plays a crucial role and there is much to gain in incorporating these modelling capabilities in GIS. This is still a rather complex task and research is being done on the full integration of these models. Interfacing between these models and GIS may be a very efficient way of overcoming the difficulties and getting very good results in terms of engineering practice. This paper presents results based on the use of Intergraph GIS coupled with Idrisi GIS. Using these two systems substantially increased the flexibility of using GIS as a tool for flood studies. A lumped (XSRAIN) and a distributed (OMEGA) hydrologic models were used to simulate flood hydrographs. The well known HEC-2 Hydraulic model was used to compute flooded areas. These models were applied in the Livramento catchment with very good results. The computation of flooded areas for different flood scenarios, and its representation in GIS, can be used in the assessment of affected property and associated damages. This is a very useful GIS-based approach to floodplain management.     

Node and element resequencing using the Laplacian of a finite element graph: Part I—General concepts and algorithm

A Finite Element Graph (FEG) is defined here as a nodal graph (G), a dual graph (G*), or a communication graph (G˙) associated with a generic finite element mesh. The Laplacian matrix ( L (G), L (G*) or L (G˙)), used for the study of spectral properties of an FEG, is constructed from usual vertex and edge connectivities of a graph. An automatic algorithm, based on spectral properties of an FEG (G, G* or G˙), is proposed to reorder the nodes and/or elements of the associated finite element mesh. The new algorithm is called Spectral PEG Resequencing (SFR). This algorithm uses global information in the graph, it does not depend on a pseudoperipheral vertex in the resequencing process, and it does not use any kind of level structure of the graph. Moreover, the SFR algorithm is of special advantage in computing environments with vector and parallel processing capabilities. Nodes or elements in the mesh can be reordered depending on the use of an adequate graph representation associated with the mesh. If G is used, then the nodes in the mesh are properly reordered for achieving profile and wavefront reduction of the finite element stiffness matrix. If either G* or G˙ is used, then the elements in the mesh are suitably reordered for a finite element frontai solver, A unified approach involving FEGs and finite element concepts is presented. Conclusions are inferred and possible extensions of this research are pointed out. In Part II of this work,¹ the computational implementation of the SFR algorithm is described and several numerical examples are presented. The examples emphasize important theoretical, numerical and practical aspects of the new resequencing method.