Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

QoS metrics-in-the-loop for endowing runtime self-adaptation to robotic software architectures

Multimedia Tools and Applications - The design of robots capable of operating autonomously in changing and unstructured environments, requires using complex software architectures in which,...     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Effect of processing on the microbiological quality and safety of chicken carcasses at slaughterhouse

Microbiological contamination of chicken meat depends on the conditions under which the animals are reared, slaughtered and processed. The aim of this study was to determine the influence of farm origin and processing stages at slaughterhouse on the microbial safety and quality of chicken. Samples of chicken carcasses from three different farms were taken from a slaughterhouse. Mesophiles, Escherichia coli, coagulase positive Staphylococcci counts, presence of Listeria monocytogenes,Campylobacter and Salmonella were determined at five sampling points: after defeathering, after evisceration, after washing, after chilling and after cutting. Chilling reduced log numbers of mesophiles, coagulase positive Staphylococci and E. coli by 0.85, 1.52 and 2.2 log units, respectively. Salmonella was not detected after chilling. High prevalence of Campylobacter spp was observed at all the stages ranging between 84% and 100%. L. monocytogenes was not detected in chicken carcasses after defeathering. However, it was detected after evisceration and after washing and chilling. The most critical stage for L. monocytogenes contamination was the portioning operation, the prevalence in breast and legs being 88% and 84%, respectively.     

Ga-doped IZO films obtained by magnetron sputtering as transparent conductors for visible and solar applications

C-axis textured thin films of gallium-doped indium zinc oxide (GIZO) with a 2% ratio of Ga/Zn, were obtained via RF-magnetron sputtering with high transparency and electrical conductivity. A Box-Behnken response surface design was used to evaluate the effects of the deposition parameters (In₂O₃ target power, deposition time, and substrate temperature) on the chemical composition, optical, electrical, and structural properties of the GIZO films. The optical constants and the electrical properties were obtained using optical models. The GIZO stoichiometry, and therefore the In/Zn atomic ratio, affected the crystallinity, crystalline parameters, band gap, and charge carrier mobility of the GIZO films. The charge carrier density was related to the change in the crystalline parameters of the hexagonal structure and the In/Zn atomic ratio. The best electrical conductivity values (1.75?×?10³ Ω^?1 cm^?1) were obtained for GIZO films with In/Zn ratio ≥?1. Several figures of merit (FOM) defined for the visible and solar regions were comparatively used to select the optimal In/Zn atomic ratio that provided the best balance between the conductivity and the transparency. The optimal In/Zn ratio was in a range of 0.85–0.90 for the GIZO films.     

Solar light-driven reduction of crystal violet by a composite of g-C3N4, β-Ag2Se, γ-Fe2O3 and graphite

Abstract

In this work, a new g-C₃N₄-based Z-scheme with γ-Fe₂O₃ and β-Ag₂Se both n-type semiconductors, and graphite to favor electron exchange is presented. The composite material was studied by XRD, FTIR, UV-Vis, TEM, XPS, TGA, DSC and TOF-SIMS, and the ability of this photocatalytic system to act as a photo-reductant was assessed using crystal violet (CV⁺) dye. Solar light driven photo-reduction of CV⁺ in the presence of tri-sodium citrate evidenced a synergistic enhancement of the activity of the composite toward reduction, with ～20 times higher conversion rates per unit of surface area than those of g-C₃N₄. Photo-oxidation experiments under Xe lamp irradiation in the presence of H₂O₂ also showed that the AgFeCN composite featured a higher activity (～8×) than g-C₃N₄. This Z-scheme may deserve further study as a photo-reductant to obtain hydrogen or hydrogenated compounds. Moreover, the use of CV⁺ may represent a facile procedure that can aid in the selection of new photocatalysts to be used in hydrogen production.