Hopping and optical absorption of electrons in nano-porous crystal 12CaO·7Al2O3

Recently it has been discovered that a nano-porous main group oxide 12CaO·7Al₂O₃ (C12A7) can be converted from a wide-gap insulator to a good transparent conductor. Using ab initio modelling we explain good conductivity of this material by very small barriers for hopping of localised electrons between neighbouring positive cages. We show that optical absorption of C12A7 in infrared region and at energies higher than 2.7 eV is due to inter-cage and intra-cage electron transitions, respectively. The proposed mechanisms can be useful in further search for conducting transparent media.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Electron transport in InGaO3(ZnO)m (m=integer) studied using single-crystalline thin films and transparent MISFETs

We have investigated the characteristics of transparent metal-insulator-semiconductor field-effect transistors (MISFETs) fabricated using InGaO₃(ZnO)_m (m=integer) single-crystalline thin films as n-channel layers and amorphous alumina as gate insulator films. The MISFETs exhibit good characteristics such as insensitivity to visible light illumination, off-current as low as ∼1 nA with a positive threshold voltage of ∼3 V and on/off current ratio of 10⁵. The field-effect mobility increased from ∼1 to ∼10 cm² (V s)⁻¹ as the m-value increased. Room temperature Hall mobility also increased. However, unexpectedly these values were lower than the field-effect mobility. It is explained by existence of shallow localized state in the homologous compounds.     

An expert system for XPLE cable deterioration diagnosis and life forecasting

The recent increase in the demand for power in urban areas has caused changes in the way power is supplied. Underground distribution systems have been introduced for convenience in urban areas and to prevent injuries in case of a crisis. As a result, many new types of power cables are being used. One type, XPLE cables (also called CV cables) have been rapidly taking the place of conventional cables such as OF or SL cables since the 1960s because of their relatively easy installation and maintainability. However, distribution cables used under severe environmental conditions deteriorate rapidly (due mainly to water treeing), and some cables experience insulation breakdown. Therefore, many diagnostic methods have been developed, though they have not been very effective. By combining methods, a high reliability can be achieved in comparison to the use of a single method. However, processing the data is difficult for on-site personnel, so many experts are required. But there is a lack of qualified experts, hence we have turned to the development of expert systems.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.