Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Critical heat flux on a flat plate heater located at the middle of a duct in forced flow of pressurized He II

Critical heat fluxes (CHFs) were measured for two types of rectangular ducts containing horizontal flat plate heaters. One has the flat plate heater of 6 mm wide and 20 mm long located on the inner lower wall at 50 mm from the inlet. The other duct has two horizontal flat plates of 6 mm wide and 20 mm long on inner upper and lower walls at 50 mm from the inlet. The equation of CHF for the forced convection containing a new nondimensional-parameter m introduced in order to calculate cross-sectionally averaged liquid temperature at the center of the duct was derived based on two fluid model, ordinary convection theorem and experimental results. It was confirmed that this correlation can describe not only the author's data on the duct but also other worker's data for channels with different shapes and sizes.     

Growth of Potassium Titanate Fibers in Flowing N2 Gas

The length of potassium titanate fibers produced by several conventional methods averages 50 μm, with a maximum of 100 μm. Extremely long fibers (most >1000 μm long) were obtained by calcination in N₂ gas flowing at 5.2×10^-4 m/s.     

Polarity control of GaN epilayers grown on ZnO templates

We report the successful growth of Ga-polar GaN epilayers on O-polar ZnO templates pre-deposited on c-sapphire. Prior to GaN growth, NH₃ is exposed onto the ZnO template. The polarity of the GaN layers is confirmed by etching of the surface and by conversion beam electron diffraction (CBED), while the O-polar ZnO is confirmed by CBED. It is suggested that the NH₃ pre-exposure helps form a Zn₃N₂ layer, which possesses inversion symmetry and inverts the crystal from anion polar to cation polar.     

Analysis of secretion and expression of platelet-derived growth factor in cultured endothelial cells from stroke-prone spontaneously hypertensive rat

1. We characterized the endothelial cell-derived growth factors of SHRSP and Wistar Kyoto rats (WKY), respectively and found that platelet-derived growth factor (PDGF)-B chain related growth factor constituted a major portion of the mitogenic activity of the conditioned media of endothelial cells from both animals. There were no remarkable qualitative differences between the endothelial cell-derived growth factors of SHRSP and WKY. 2. Northern analysis revealed that the expression of PDGF-B chain was 2-4-fold enhanced in cultured aortic endothelial cells of SHRSP. This enhanced expression of PDGF-B chain, which may be induced under chronic hypertensive conditions, is suggested to contribute to the increase in endothelial cell-derived growth factors reported in this animal.     

Properties of Stabilizing PID Gain Set in Parameter Space

The properties of the PID gain set for which all the closed-loop poles lie in the left half of the complex plane are examined on the parameter plane. A new method of determining the increase in the number of unstable poles when the gain crosses the boundary of stability regions is proposed. This method is useful for determining the number of unstable poles in each region. These results are extended to Gamma-stability based on conformal mapping.     

The combined method: a novel access technique for fetal endoscopic surgery

BACKGROUND/PURPOSE: To develop practical and less invasive techniques for fetal endoscopic surgery, new methods of lifting the uterine wall to allow fetal surgery without maternal laparotomy were developed and assessed. METHODS: Fetal endoscopic surgical procedures, including tracheostomy and umbilical vascular cannulation, were performed using one of the three methods to enter the uterus without maternal laparotomy in pregnant goats (n = 6; 105 to 115 days' gestation): (1) direct uterine lifting with an air-cushion device; (2) indirect uterine lifting, in which the uterine wall was fixed to the maternal abdominal wall using balloon tip ports inserted percutaneously by Seldinger's method, then the maternal abdomen was lifted mechanically; and (3) combined method, in which low pressure CO2 (5 mm Hg for initial inflation and 2 mm Hg for maintenance) was insufflated into the uterus in addition to the indirect uterine lifting cited above. RESULTS: The direct uterine lifting caused massive injury of myometrium and uterine membranes. The creation of intrauterine space and the protection of the membranes were not accomplished effectively by the indirect uterine lifting only. The combined method provided the adequate intrauterine space and excellent endoscopic visibility for completion of the endoscopic procedures with minimal uterine injury. CONCLUSION: The fetal endoscopic surgery may be accomplished simply and safely by the combined method, a novel technique of uterine lifting to allow fetal surgery without maternal laparotomy.     

Software engineering in Asia

Asia boasts a growing software industry spread across several countries. However, software technology in Asia still lags behind the US. To become competitive in the global marketplace, many Asian countries have started to improve their university systems and software-development industries. If successful, by 2001 their efforts will create an Asian software industry quite different from today's. The authors survey these efforts and sketch briefly the history of software development in each country. They survey recent trends in Asian software engineering from the industrial, educational, and organizational viewpoints, and offer an optimistic assessment of efforts toward modernization and regional cooperation     

New polylactide/layered silicate nanocomposites. 5. Designing of materials with desired properties

Understanding the structure/property relationship in polymer/layered silicate nanocomposites is of great importance in designing materials with desired properties. In order to understand these relations, a series of polylactide (PLA)/organically modified layered silicate (OMLS) nanocomposites have been prepared using a simple melt extrusion technique. Four different types of OMLS have been used for the preparation of nanocomposites, three were modified with functionalized ammonium salts while fourth one was a phosphonium salt modified OMLS. The structure of the nanocomposites in the nanometer scale was characterized by using wide-angle X-ray diffraction and transmission electron microscopic observations. Using four different types of layered silicates modified with four different types of surfactants, the effect of OMLS in nanocomposites was investigated by focusing on four major aspects: structural analysis, thermal properties and spherulite morphology, materials properties, and biodegradability. Finally, we draw conclusions about the structure/property relationship in the case of PLA/OMLS nanocomposites.